Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Standard Drill Bit Size: Chart for Metal and Wood

Standard drill bit sizes run as fractions of an inch, letters A to Z, and numbers #1 to #60, and the size you pick sets the hole you get.

Standard Drill Bit Size: Chart for Metal and Wood
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Drill Doctor 750X Drill Bit SharpenerDrill Doctor 750X Drill Bit Sharpener9.6/10View on Amazon
  2. 2BOSCH CO21B 21-Piece Assorted Set with Included Case CobaltBOSCH CO21B 21-Piece Assorted Set with Included Case Cobalt9.7/10View on Amazon
  3. 3MACXCOIP 29PcsMACXCOIP 29Pcs9.7/10View on Amazon

A drill bit that is a hair off the size you need leaves a hole that will not take the bolt, and a bit that is too big leaves a hole the fastener rattles in. Standard drill bit size is the system of fractional, letter and number sizes that tells you what hole a bit cuts, so you can match the bit to the hole before you drill. This guide lays out the systems and how to read them.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Standard drill bit size: the systems

Drill bits come in fractional sizes, letter sizes and number sizes, and a full set can hold all of them at once. Fractional sizes are named in fractions of an inch, letter sizes are named with letters from A to Z, and number sizes are named with numbers from #1 to #60. The 115-piece cobalt set in the listings below holds 29 fractional sizes from 1/16 to 1/2 inch in 1/64 inch steps, 26 letter sizes from A to Z, and 60 number sizes from #1 to #60. That set is one example of how the systems sit side by side in one index box, and the size markings on the holder tell you which bit you are holding.

Side by side

Fractional Letter Numbered
Sizes named by Fractions of an inch Letters A to Z Numbers #1 to #60
Range in the 115-piece set 1/16 to 1/2 in A to Z #1 to #60
Pieces in the 115-piece set 29 26 60
Step between sizes 1/64 in One letter at a time One number at a time

The fractional column matches the bolts and holes measured in inches. Letter and number sizes fill the gaps between fractions, which matters when a hole has to fit a fastener that a fraction size would leave loose or tight.

Fractional sizes

Fractional sizes run from 1/16 to 1/2 inch in the 115-piece set, stepping in 1/64 inch increments, which gives 29 sizes in that set. The 122-piece cobalt set stocks the same fractional range, 1/16 to 1/2 inch, and holds more of the small sizes it expects you to use often: 30 of the 1/16 size, 20 of the 5/64 size, 10 of the 1/8 size, 10 of the 3/32 size and 5 of the 1/4 size. The full fractional run in that set reads 1/16, 5/64, 3/32, 7/64, 1/8, 9/64, 5/32, 11/64, 3/16, 13/64, 7/32, 15/64, 1/4, 17/64, 9/32, 5/16, 3/8, 7/16 and 1/2 inch. Smaller sets cover less of the range: the COMOWARE titanium set holds 16 pieces from 1/16 to 1/4 inch, so it stops at the quarter inch size where the larger sets keep going to 1/2 inch. Read the range on the set before you buy, and match it to the hole sizes your work calls for.

Letter sizes

Letter sizes run from A to Z, and the 115-piece set holds 26 of them, one for each letter. A letter size is a drill bit size in its own right, not a fraction with a letter stamped on it, and the letter tells you where the bit sits between the fractional sizes. The Q size is one of the letter sizes in the A to Z set, and the listings here do not state a diameter for Q, so check the size markings on the index box of the set you buy. Letter sizes show up in sets aimed at metal work, where a hole has to match a tap or a fastener more closely than a fraction step allows.

Number sizes

Number sizes run from #1 to #60, and the 115-piece set holds 60 of them. The numbers run the other way from the letters: #1 is the largest number size and #60 is the smallest, so a higher number means a smaller bit. The smallest number sizes fall below the smallest fractional size the set stocks, so they extend the range downward where the fractions in that set stop, and they sit alongside the letter sizes in the same index box. When a listing says a set holds #1 to #60, it means the full number run is in the box.

Point angles and shanks

The point angle and the shank decide how the bit starts and how it mounts. The Makita 14-piece titanium (on Amazon) set and the 115-piece cobalt set state a 135 degree split point, and the cobalt set says the split point is self-centering to prevent walk-off, which helps the bit start where you put it instead of skating across the metal. The COMOWARE 16-piece set and the Makita 14-piece set use a 1/4 inch hex shank, and the COMOWARE listing says the hex shank fits into all power tools and locks into a quick change chuck. The 115-piece cobalt set uses a round straight shank. Check the shank your drill takes before you buy a set, since a hex shank and a straight shank do not mount the same way.

What the sets cover

Materials and coatings decide what a set can drill. The 115-piece cobalt set lists M35 high speed steel with 5% cobalt, and says it suits hardened metal, stainless steel, plastics, cast iron and wood. The Makita 14-piece set lists titanium nitride coating, and says it drills ferrous metal, wood, plastic, non-ferrous metal, cast iron and stainless steel, with a maker claim that the coating lasts 2.5 times longer than non-coated bits. The 122-piece cobalt set lists M35 cobalt steel with a maker claim of hardness up to 67 and up to 12 times the life of an average HSS titanium coated bit. The COMOWARE 16-piece set lists high speed steel with a titanium coating and says it suits wood, plastic and aluminum alloy, and the 246-piece COMOWARE combo kit adds masonry and brad point bits alongside twist bits, plus screwdriver bits, nut drivers and hex keys in the same case. See our best twist drill bit set picks and the best drill bit set for wood and metal guide for sets matched to the material, and the carbide vs cobalt drill bits guide and the titanium vs black oxide drill bits guide for the coatings these sets list.

FAQ for welders

What size drill bit do I need for a 1/4 inch hole?

A 1/4 inch bit cuts a 1/4 inch hole, so pick a bit marked 1/4 inch. The COMOWARE 16-piece set runs from 1/16 to 1/4 inch, so it covers that hole, and the 115-piece and 122-piece sets run from 1/16 to 1/2 inch, so they cover it too.

What is a Q size drill bit?

Q is a letter size drill bit, one of the letter sizes that run from A to Z. The 115-piece set in the listings holds 26 letter sizes from A to Z, and the listings do not state a diameter for Q, so check the size markings on the index box of the set you buy.

What are number size drill bits?

Number sizes run from #1 to #60, and the 115-piece set holds 60 of them. The numbers run the other way from the letters: #1 is the largest number size and #60 is the smallest, so a higher number means a smaller bit.

What does 1/64 inch mean on a drill bit set?

It means the fractional sizes step in 1/64 inch increments. The 115-piece set holds 29 fractional sizes from 1/16 to 1/2 inch in 1/64 inch steps, so each size is 1/64 inch larger than the last.

What is a 135 degree split point?

It is a point ground at 135 degrees with a split that helps the bit start without wandering. The Makita 14-piece set and the 115-piece cobalt set state a 135 degree split point, and the cobalt set says the split point is self-centering to prevent walk-off.

Related: best cobalt drill bit set, step drill bit vs twist drill bit, best drill bits for steel, and the metal fab tools hub.

More buying guides