Are Flux Core Welders Any Good?
Flux core welders suit outdoor repairs and thicker steel on a small machine, and 4 gasless wire feed welders show what the process does well and where a gas machine fits better.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
DURATECH 125A MIG Welder9.7/10View on Amazon - 2
Lincoln Electric Weld-Pak 90i FC Flux-Cored Wire9.6/10View on Amazon - 3
Sunstac 140A 3 in 1 MIG Welder 110V with IGBT9.6/10View on Amazon - 4
YESWELDER 135A MIG Welder9.6/10View on Amazon
A cracked gate hinge waits on the bench, and the only question is whether a small gasless welder can put it back together without a gas cylinder in the truck. The question, are flux core welders any good, comes down to what the job needs: outdoor repairs, thicker steel and a machine that runs on a household outlet. The short answer is yes for that kind of work, and less so for thin sheet and visible work, and this guide shows why with 4 gasless machines as examples.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
| # | Product | Gear Score | Buy |
|---|---|---|---|
| 1 | DURATECH 125A MIG Welder | 9.7/10 | Buy on Amazon |
| 2 | Lincoln Electric Weld-Pak 90i FC Flux-Cored Wire | 9.6/10 | Buy on Amazon |
| 3 | Sunstac 140A 3 in 1 MIG Welder 110V with IGBT | 9.6/10 | Buy on Amazon |
| 4 | YESWELDER 135A MIG Welder | 9.6/10 | Buy on Amazon |

DURATECH 125A MIG Welder
A 120V flux core welder with up to 125 amps, a 15A to 20A plug adapter, and a 2 year warranty.
Pros
- Up to 125 amps, stated for mild steel up to a 3/16 inch plate
- CSA certified and fully complies with U.S. standards
- 10.5 pounds with a hand grip and a 15A to 20A plug adapter
- Infinite voltage and wire feed speed control for dialing in the weld
Cons
- Flux core only, so a buyer who wants gas MIG needs a different machine
- Handles 2-pound rolls of wire, and the wire is not included
- No duty cycle figure is stated, so the rated work rate is unclear
- No digital screen is stated, so there is no on-screen readout of voltage and wire feed speed

Lincoln Electric Weld-Pak 90i FC Flux-Cored Wire
A 120V flux-cored wire feed welder with a 20 to 120 amp range, a 30% duty cycle at 90 amps, and a combo kit with gloves and flux-cored wire.
Pros
- 20 to 120 amp range with infinite welding voltage for fine-tuning
- 30% duty cycle at 90 amps, stated with the amp figure
- Shoulder strap and 15.0 pound inverter design for carrying to the job
- Combo kit includes extra large metal working gloves and flux-cored wire
Cons
- Flux core only, so a buyer who wants gas MIG needs a different machine
- 15.0 pounds, heavier than the 10.5 pound DURATECH and the 11.24 pound Sunstac
- 12 month warranty, shorter than the 2 year warranty on the DURATECH
- Duty cycle is stated only at 90 amps, not across the 20 to 120 amp range

Sunstac 140A 3 in 1 MIG Welder 110V with IGBT
A 110V 3-in-1 welder with 140 amps, synergic control, an LCD screen, and flux core, stick and lift TIG processes.
Pros
- 140 amps, the highest output of the 4 machines here
- 3-in-1 processes: flux core, stick and lift TIG
- Synergic control with an LCD digital screen that shows voltage and current
- MIG torch, stick electrode holder, work clamp and 1 lb of welding wire in the pack
Cons
- No warranty term is stated
- No duty cycle figure is stated
- 11.24 pounds, heavier than the 10.5 pound DURATECH
- No voltage micro-adjustment is stated, unlike the YESWELDER with its ±3V adjustment

YESWELDER 135A MIG Welder
A 110V 3-in-1 welder with 135 amps, synergic control, a ±3V voltage micro-adjustment, and flux core, lift TIG and stick processes.
Pros
- 135 amps, stated for mild steel up to 3/32 inch thick
- 3-in-1 processes: flux core MIG, lift TIG and stick
- Synergic control with a ±3V voltage micro-adjustment for fine-tuning
- No shielding gas cylinder needed, for outdoor, windy or all-position welding
Cons
- No warranty term is stated
- No duty cycle figure is stated
- No weight or dimensions are stated
- Lift TIG torch is extra and not included in the box
Are flux core welders any good?
For outdoor repairs and thicker steel on a household outlet, yes. A flux core wire carries its own shielding in the wire, so there is no gas cylinder to haul, no regulator to set and nothing for the wind to blow away. That makes the process a strong fit for fence posts, gates, trailers and equipment in a field. The trade is more smoke, more spatter and slag to chip, and a harder time on thin sheet, where the extra heat burns through. So the answer depends on the job on the bench, not on the machine alone.
When flux core is the right call
- Outdoor work. Fence posts, gates, trailers and equipment in a field. A breeze that ruins gas shielding barely affects flux core.
- No cylinder. You avoid buying or renting a cylinder and regulator, and there is nothing to refill. The YESWELDER machine (on Amazon) is built for it: gasless flux core MIG for outdoor, windy or all-position welding.
- Thicker steel on a small machine. Flux core tends to penetrate deeper at a given setting, which helps on 120V. The DURATECH states mild steel up to a 3/16 inch plate.
- Simple setup. The Sunstac comes with a MIG torch, stick electrode holder, work clamp and 1 lb of welding wire, so it is ready to use after it arrives.
The best flux core welder guide covers gasless machines by stated output.
When a gas machine fits better
- Thin sheet and auto body. Lower heat and cleaner small beads make thin panels easier with less burn through.
- Looks and cleanup. No slag to chip and less spatter to grind, which matters on visible work and furniture.
- Indoor shop work. Less smoke than flux core, though you still need ventilation.
- Aluminum. Possible with gas MIG through a spool gun or push feed setup and argon. The 4 machines here list no aluminum work.
All 4 machines here are gasless flux core machines, and none lists gas MIG, so a buyer who wants gas later needs a machine that lists it.
Flux core smoke and slag. Flux core makes more smoke and fumes than gas MIG, and hot slag can flick off when you chip it. Weld with good ventilation or outdoors with your head out of the plume, wear safety glasses under the helmet when chipping, and clear dry grass and anything flammable from the area. See the OSHA welding overview and our Safety Disclaimer.
Side by side
| Welder | Gear Score | Max amps | Input | Duty cycle | Weight | Warranty |
|---|---|---|---|---|---|---|
| DURATECH 125A MIG | 9.7/10 | 125 amps | 120V | Not stated | 10.5 pounds | 2 year warranty |
| Lincoln Weld-Pak 90i FC | 9.6/10 | 120 amps | 120V | 30% at 90 amps | 15.0 pounds | 12 months |
| Sunstac 140A 3-in-1 | 9.6/10 | 140 amps | 110V | Not stated | 11.24 pounds | Not stated |
| YESWELDER 135A FLUX-135 | 9.6/10 | 135 amps | 110V | Not stated | Not stated | Not stated |
Amps are the maker’s stated output. The Lincoln lists a 20 to 120 amp range, the DURATECH lists up to 125 amps, the YESWELDER lists 135 amps and the Sunstac lists 140 amps. Duty cycle is stated only for the Lincoln, at 30% at 90 amps; the other 3 state no duty cycle figure, so compare them on amps, input and weight instead. The welding duty cycle explained guide shows what a duty cycle figure means.
4 gasless welders for the jobs above
Each machine below handles one part of the answer above: the Lincoln and the DURATECH cover small flux core repairs on 120V, while the Sunstac and the YESWELDER add stick and lift TIG for a buyer who wants 3 processes on 110V.
FAQ for welders
Is flux core welding as strong as MIG?
Both can make sound welds on mild steel when the wire, settings and technique suit the joint. Strength depends more on the joint and the welder’s skill than the process. For structural or load bearing work, have a certified welder do or inspect it.
Can I use flux core wire in a MIG welder?
Usually, if the machine lists flux core and you set the polarity the wire calls for. Check the wire label and the machine manual before you start.
Can a flux core only welder be converted to gas?
Generally not. Gas MIG needs a gas valve and path in the machine and gun. If you might want gas later, buy a machine that lists gas MIG now.
Why is my flux core weld covered in a crust?
That is slag from the flux, and it is normal. Chip it off with a chipping hammer and wire brush before the next pass or painting.
Which flux core welder here weighs the least?
The DURATECH at 10.5 pounds, followed by the Sunstac at 11.24 pounds and the Lincoln at 15.0 pounds. The YESWELDER states no weight.
Related: how to choose a MIG welder, best flux core welder, best welder for beginners, flux core vs MIG, and the welders hub. Also see our why a MIG welder spatters.




