Diagram Arc Welding Machine Parts: What Each Part Does
A diagram arc welding machine parts guide that maps the MIG gun, cable, nozzle, contact tip, gas diffuser and liner to the welders they fit.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
10FT MIG Welding Torch Gun 15AK-Style Parts 180A9.6/10View on Amazon - 2
10ft MIG welding gun 180A fits Titanium Unlimited9.5/10View on Amazon - 3
MIG Welding Gun Torch 100Amp 15' Replacement9.4/10View on Amazon - 4
15ft Mig Gun Parts Replacement Compatible9.4/10View on Amazon
A torch stops feeding wire in the middle of a bead, and the diagram arc welding machine parts chart is the way to find the fault. The chart names the gun, the cable, the nozzle, the contact tip, the gas diffuser and the liner, and shows how wire and gas travel from the machine to the joint. This guide walks through each part in that order, then matches replacement guns to the Lincoln, Titanium and Hobart welders in the gear section below.
This guide links to product roundups, where WeldGearLab earns a commission when a purchase is made through links, at no extra cost to the buyer.

10FT MIG Welding Torch Gun 15AK-Style Parts 180A
A 180A MIG gun with a 10 ft cable, a 5-pin connector for Titanium welders, and a full kit of nozzles, diffuser, tips and liner.
Pros
- Rated to 180A for light and medium MIG work
- Kit includes 2 nozzles, 1 gas diffuser, 10 contact tips and 1 wire liner
- 5-pin connector for Titanium Unlimited 200, MIG170 and MIG140 welders
- Ergonomic grip handle with trigger lock, plus heat-resistant insulation
Cons
- 10 ft cable is shorter than the 15 ft guns in this guide
- Only fits Titanium welders with a 5-pin socket, not 2-pin Euro connector models
- 180A rating caps the work at light and medium MIG jobs
- No warranty term is stated

10ft MIG welding gun 180A fits Titanium Unlimited
A 180A MIG gun with a 10 ft cable and a 5-pin connector, sold with 15AK-style tips, nozzles and a gas diffuser for Titanium welders.
Pros
- Rated to 180A
- Kit includes 10 15AK tips, 2 nozzles and 1 gas diffuser
- 5-pin connector fits Titanium Unlimited 200, MIG170 and MIG140 welders
- Runs flux-cored and gas-shielded wire
Cons
- 10 ft cable is shorter than the 15 ft guns in this guide
- 5-pin connector only fits the Titanium Unlimited 200, MIG170 and MIG140 welders
- No liner is named in the kit list
- No warranty term is stated

MIG Welding Gun Torch 100Amp 15' Replacement
A 100A replacement MIG gun with a 15 ft cable for Lincoln Magnum 100L welders, using 21 series nozzles, 11 series tips and a 35-40-15 liner.
Pros
- 15 ft cable for reach around the bench
- Fits a wide list of Lincoln SP, Pro-MIG, Weld-Pak and Powermig models
- Uses the same consumables as Lincoln: 21 series nozzles, 11 series tips and a 35-40-15 liner
- Feeds .030-.035 diameter welding wire
Cons
- 100A rating is the lowest in this guide
- Fits Lincoln models only, and does not fit Titanium or Hobart welders
- Sold as the gun torch on its own, with no spare nozzle, tip or diffuser named in the package list
- Feeds .030-.035 wire only

15ft Mig Gun Parts Replacement Compatible
A 15 ft MIG gun for Hobart Handler welders, sold with 5 contact tips in .030, a diffuser and a nozzle.
Pros
- 15 ft cable for reach around the bench
- Fits Hobart Handler 130XL, 135, 140, 175 and 187, plus AutoArc XLT142 and XLT182
- Kit includes 5 contact tips in .030, 1 diffuser and 1 nozzle
- Replacement for Hobart H-10 and H100S2-10 guns
Cons
- No amp rating is named, so the gun cannot be matched to a job by amps
- Kit has 5 contact tips, 1 diffuser and 1 nozzle, fewer spares than the 10-tip kits here
- Fits Hobart Handler and AutoArc models only
- No liner is named in the package list
Diagram Arc Welding Machine Parts: The Main Parts
The gun holds the trigger, the handle and the consumables at the work end, while the cable carries wire and gas from the machine to the gun. The contact tip sits inside the nozzle and passes current to the wire as the wire leaves the liner. The gas diffuser spreads shielding gas around the wire, and the nozzle directs that gas over the puddle. The liner runs inside the cable and guides the wire from the drive to the tip.
How the Parts Fit Together
Wire leaves the machine, travels through the liner inside the cable, and exits through the contact tip, while gas travels the same cable and spreads through the diffuser before the nozzle directs it over the joint. The trigger on the handle starts the feed, and the connector at the machine end sets which guns fit: the Titanium guns in this guide use a 5-pin connector, and the maker warns that the 5-pin plug does not fit 2-pin Euro connector models.
Reading the Diagram for Your Machine
Start with the gun the machine was sold with, then match the replacement by connector, cable length and consumable style. A Lincoln Magnum 100L gun takes 21 series nozzles, 11 series tips and a 35-40-15 liner, and feeds .030-.035 diameter wire. A Titanium gun takes 15AK-style parts, and a Hobart gun takes the contact tips, diffuser and nozzle in its kit.
The Replacement Guns at a Glance
The table below lines up the replacement guns in this guide by cable length and fitment, so the diagram part can be matched to the machine on the bench.
| Product | Gear Score | Cable length | Fit |
|---|---|---|---|
| HOPWELD 15AK-Style MIG Gun | 9.6/10 | 10 ft | Titanium Unlimited 200, MIG170 and MIG140 |
| Hasweld Titanium 10ft MIG Gun | 9.5/10 | 10 ft | Titanium Unlimited 200, MIG170 and MIG140 |
| OKBA Magnum 100L MIG Gun | 9.4/10 | 15 ft | Lincoln Magnum 100L K530-5 |
| Hasweld Hobart 15ft MIG Gun | 9.4/10 | 15 ft | Hobart Handler 130XL, 135, 140, 175 and 187 |
Replacement MIG Guns for These Machines
Each gun below handles the torch end of the diagram: the cable, the trigger, the consumables and the connector that ties the gun to the machine.
FAQ for welders
What does a MIG gun diagram show?
A MIG gun diagram shows the gun, the cable, the nozzle, the contact tip, the gas diffuser and the liner, and how they connect to the machine. It shows the path wire takes from the drive to the tip, and the path gas takes through the diffuser and nozzle.
Which contact tip size fits these guns?
The Lincoln gun feeds .030-.035 diameter wire, and its style uses 11 series tips. The Hobart kit includes contact tips in .030, and the HOPWELD kit includes contact tips in .030, so match the tip to the wire diameter in the listing.
How do I know a replacement gun fits my welder?
Match the connector and the model list in the listing. The Titanium guns here use a 5-pin connector for Titanium Unlimited 200, MIG170 and MIG140 welders, and the maker states the plug does not fit 2-pin Euro connector models.
What comes in a replacement gun kit?
It varies by gun. The HOPWELD kit includes 2 nozzles, 1 gas diffuser, 10 contact tips and 1 wire liner, the Hasweld Titanium (on Amazon) kit includes 10 15AK tips, 2 nozzles and 1 gas diffuser, while the Hobart kit includes 5 contact tips, 1 diffuser and 1 nozzle, and the Lincoln gun is sold as the gun torch on its own.
Which part wears out on a MIG gun?
Contact tips, nozzles and diffusers are the wear parts, which is why the kits in this guide include spares. A tip that has worn wide feeds wire rough, and a nozzle clogged with spatter shields the puddle poorly.
Related: MIG welding gun parts, MIG welder replacement parts, MIG welding contact tips, and the welders hub.




