MIG Welding Contact Tips: When and How to Replace Them
A mig welding contact tip carries the wire and the current to the puddle, and this guide shows when to swap one and which listed packs fit your gun.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
YESWELDER 25-Pk MIG Contact Tips 11-35 (0.035")9.6/10View on Amazon - 2
STARTECHWELD 1435 Mig Welding Contact Tips .035"9.6/10View on Amazon - 3
Welding Knight MIG Welding Contact Tips9.5/10View on Amazon - 4
TimelyDu Mig Welder Tips 30-Pack Welding Tips9.5/10View on Amazon
The bead goes ragged halfway down the joint. The wire stutters, the arc pops, and the puddle will not sit still. When that happens, the mig welding contact tip is the first part to check. This guide shows when to swap a tip, how to match one to the wire and the gun, and which listed packs fit the common guns.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

YESWELDER 25-Pk MIG Contact Tips 11-35 (0.035")
A 25-pack of standard 11-35 tips in .035 in for Lincoln Tweco 100L and Mini guns, with diffuser sizes stated.
Pros
- Standard 11-35 tips for Lincoln Tweco 100L and Mini guns
- Diffuser sizes stated: 35-50 or 51
- 25 tips in the pack
- Straightforward replacement, easy setup stated
Cons
- No length is stated
- No thread size is stated
- No material is stated
- No warranty term is stated

STARTECHWELD 1435 Mig Welding Contact Tips .035"
A 25-pack of 14-35 tips in .035 in for Tweco 2, 3 and 4 guns and Lincoln Magnum 200, 300 and 400 guns, with the size range stated.
Pros
- Fits Tweco 2, 3 and 4 and Lincoln Magnum 200, 300 and 400
- Size range stated, 14-23 through 14-116
- 25 tips in the pack
- Dimensions stated: 1.5 x 0.25 x 0.25 in
Cons
- No material is stated
- No thread size is stated
- No warranty term is stated
- No diffuser fitment is stated

Welding Knight MIG Welding Contact Tips
A 20-pack of .035 in tips, 0.9 mm, with a non-stick coating on a copper base, M6 thread and a 25 mm length, for 15AK torches and 100L Mini guns.
Pros
- Non-stick coating to keep spatter off the tip
- Copper base, stated heat and wear resistance
- Length and thread stated: 25 mm, M6
- 20 tips in the pack
Cons
- Title says ceramic tips, bullets say a copper base
- No warranty term is stated
- Smallest pack here at 20 tips
- Coating life is not stated

TimelyDu Mig Welder Tips 30-Pack Welding Tips
A 30-pack of .030 in tips, 0.8 mm, in copper with an M6 x 1.0 thread, for Lincoln, Tweco and Binzel mini MIG guns.
Pros
- 30 tips, the largest pack here
- Copper with stated conductivity and heat resistance
- Thread stated: M6 x 1.0
- Fits Lincoln, Tweco and Binzel mini MIG guns
Cons
- Only .030 in size; no .035 in option in this listing
- No length is stated
- No warranty term is stated
- No diffuser fitment is stated
How mig welding contact tips wear out
The tip is the last part the wire touches before the arc, and it carries the current as well as the wire. Heat and spatter wear the bore, the opening goes oval, and the wire drags and wanders. A worn tip shows up as an erratic arc, spatter on the nozzle, and a bead that will not lay flat. When the wire feeds rough or the arc pops for no clear reason, the tip is the first part to check.
When to swap a tip
Swap the tip when the bore looks worn or oval, when the wire drags on the way out, or when the arc stays erratic after you check the drive rolls and liner. Spatter caked on the tip face is a sign the coating has given up, and no cleaning fixes a bore that has gone oval.
Match the tip to the wire and the gun
Wire size comes first. A .035 in tip fits .035 in wire, and a .030 in tip fits .030 in wire; a loose tip makes a poor connection and an erratic arc. Thread and gun style come next. The listings here use an M6 thread on the coated and copper mini-gun tips, an 11-35 style for Lincoln Tweco 100L and Mini guns, and a 14-35 style for Tweco 2, 3 and 4 guns and Lincoln Magnum 200, 300 and 400 guns. Check the gun tube and the diffuser too: the YESWELDER listing names a 35-50 or 51 gas diffuser by gun tube.
Mig welding contact tips for the bench
Each tip below handles one part of the same job: carrying the wire and the current to the puddle on the gun you already run.
Side by side
| YESWELDER 11-35 (25-Pk) | STARTECHWELD 14-35 (25-Pk) | Welding Knight .035 (20-Pk) | TimelyDu .030 (30-Pk) | |
|---|---|---|---|---|
| Wire size | .035 in | .035 in | .035 in (0.9 mm) | .030 in (0.8 mm) |
| Pack size | 25 | 25 | 20 | 30 |
| Thread | Not stated | Not stated | M6 | M6 x 1.0 |
| Fits | Lincoln Tweco 100L, Mini | Tweco 2, 3, 4; Lincoln Magnum 200, 300, 400 | 15AK, Lincoln Tweco 100L Mini | Lincoln, Tweco, Binzel mini MIG |
| Material | Not stated | Not stated | Copper, non-stick coating | Copper |
| Gear Score | 60 | 58 | 55 | 54 |
Pack size and wire size decide most of the choice. The .035 in tips fit the common mini and full-size guns in this guide, while the .030 in pack suits a lighter wire setup. Match thread and diffuser fitment to the gun before you buy.
FAQ for welders
How often should I replace mig welding contact tips?
Replace a tip when the bore looks worn or oval, when the wire drags, or when the arc stays erratic after you check the drive rolls and the liner. A tip that still feeds straight and holds a steady arc is fine to keep running.
Can I use a .035 in tip with .030 in wire?
No. The tip must match the wire size, because a loose tip makes a poor connection and the arc wanders. Run a .035 in tip on .035 in wire, and a .030 in tip on .030 in wire. The packs in this guide are sized for one wire size each.
Do mig welding contact tips fit every MIG gun?
No. Fit depends on thread and gun style. The 11-35 tips here fit Lincoln Tweco 100L and Mini guns, the 14-35 tips fit Tweco 2, 3 and 4 guns and Lincoln Magnum 200, 300 and 400 guns, and the M6 thread tips fit 15AK torches and mini MIG guns.
What does the coating on a contact tip do?
The Welding Knight tips (on Amazon) carry a non-stick coating that keeps spatter off the tip, so the area stays clean and the tip lasts longer between swaps. Once spatter cakes on and the coating has given up, swap the tip.
Can I clean a contact tip instead of replacing it?
You can wipe spatter off the outside of a tip, but a bore that is worn or oval will not feed wire straight, and no cleaning fixes that. Swap the tip when the wire drags or the arc wanders.
Related: best welder for beginners, best flux core welder, how to choose a MIG welder, and the welding consumables hub.




