MIG Welding Tips .035: Gas, Feed and Prep for Clean Beads
Tips for running .035 MIG wire on steel: gas choice, feed, prep and four ER70S-6 spools compared.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
PGN ER70S-6 .035" Solid MIG Welding Wire9.6/10View on Amazon - 2
TOOLIOM ER70S-6 .035" Mild Steel MIG Welding Wire9.6/10View on Amazon - 3
Blue Demon ER70S6 X .035 X 33 LB MIG/GMAW Carbon9.6/10View on Amazon - 4
Sidco Supply Solid MIG Welding Wire9.6/10View on Amazon
A bead that spatters, a wire that stubs into the plate, a puddle that will not wet in at the toes: most .035 MIG trouble comes back to setup, not the spool. Gas choice, drive roll tension, stickout and clean metal decide more than the brand on the spool. These mig welding tips .035 cover the setup that keeps the arc steady and the bead flat on mild steel.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

PGN ER70S-6 .035" Solid MIG Welding Wire
A .035 inch ER70S-6 solid MIG wire on a 44 lb spool, with high silicon and manganese deoxidizers for low spatter and smoother beads.
Pros
- 44 lb spool, the largest spool here, for long runs without a spool change
- High silicon and manganese deoxidizers support smoother welds
- Low spatter for single-pass and multi-pass welding
- Packed to help prevent tangles and support easier handling
Cons
- No shielding gas is stated, so the gas choice is left to the welder
- No warranty term is stated
- 44 lb spool suits high-volume work, not occasional small repairs
- One spool in the box, so there is no spare when it runs out

TOOLIOM ER70S-6 .035" Mild Steel MIG Welding Wire
Two .035 inch ER70S-6 spools of 10 lb each, with high manganese and silicon for strong welds, minimal spatter and smooth feeding.
Pros
- Two 10 lb spools in the box, so a spare is on hand
- Works with 100% CO2 or a mix of 80% argon and 20% CO2
- High manganese and silicon for strong welds and minimal spatter
- ABS plastic spool built to survive rough shipping
Cons
- 10 lb spools run out faster than the 33 and 44 lb spools here
- Shielding gas is not included
- Spool fit is named for TOOLIOM machines, so other machines need a spool size check
- No stated use for aluminum

Blue Demon ER70S6 X .035 X 33 LB MIG/GMAW Carbon
A .035 inch ER70S-6 carbon steel MIG wire on a 33 lb spool, made for all-position welding with low spatter and porosity-free welds.
Pros
- 33 lb spool, a common shop size for steady work
- All-position wire for general shop work, steel castings and forging salvage
- Maker claims porosity-free, x-ray quality welds
- Low spatter for cleaner beads and less cleanup
Cons
- Warranty is stated as no additional warranty
- Requires a shielding gas, CO2 and/or CO2 mix, which is not included
- One spool in the box, so there is no spare when it runs out
- Listed for carbon steel and castings, with no stainless steel use stated

Sidco Supply Solid MIG Welding Wire
A .035 inch ER70S-6 mild steel MIG wire on a 33 lb spool, copper plated and layer wound, with high manganese and silicon deoxidizers.
Pros
- 33 lb spool of copper-plated, layer wound wire for steady feeding
- High manganese and silicon deoxidizers for welds on dirty and rusty steel
- Works with 100% CO2 and CO2/argon mix shielding gases
- Maker states little to zero post-weld cleanup with a smoother bead
Cons
- No warranty term is stated
- One spool in the box, so there is no spare when it runs out
- Made for mild steel, so it does not suit aluminum work
- Shielding gas is not included
MIG welding tips .035: gas, feed and prep
Gas first. ER70S-6 solid wire needs shielding gas, and the listings here name CO2 or an argon and CO2 mix. The TOOLIOM wire (on Amazon) runs on 100% CO2 or a mixed gas of 80% argon and 20% CO2, the Blue Demon wire (on Amazon) takes CO2 and/or a CO2 mix, and the Sidco wire takes CO2 or argon/CO2. The PGN listing states no gas, so check the wire label before striking an arc.
Feed next. The wire runs through drive rolls, a liner and a contact tip sized for the wire, and a kink or a worn liner shows up as a stuttering arc. Keep the spool from overrunning and the gun cable as straight as the job allows. The TOOLIOM spool is ABS plastic and the PGN spool is packed to help prevent tangles.
Prep last. ER70S-6 carries high levels of manganese and silicon deoxidizers, and the Blue Demon and Sidco listings say the wire handles poor fit-up and dirty or rusty steel. Clean metal still welds easier, so grind mill scale and rust off the joint and close the gap before welding.
Side by side
| Wire | Gear Score | Diameter | Spool | Shielding gas | Warranty (stated) |
|---|---|---|---|---|---|
| PGN ER70S-6 .035 44 lb | 9.6/10 | .035 in | 44 lb | Not stated | Not stated |
| TOOLIOM ER70S-6 .035 10 lb 2-Pack | 9.6/10 | .035 in | 10 lb x 2 | 100% CO2 or 80% Ar / 20% CO2 | Not stated |
| Blue Demon ER70S-6 .035 33 lb | 9.6/10 | .035 in | 33 lb | CO2 and/or CO2 mix | No additional warranty |
| Sidco ER70S-6 .035 33 lb | 9.6/10 | .035 in | 33 lb | CO2 or Argon/CO2 | Not stated |
All four spools are ER70S-6 solid wire in .035, so the choice is spool size, gas match and packaging. Weights and gas are as the makers state them.
The wire: four .035 spools
Wire choice is the feed step: every spool here is ER70S-6 in .035, so pick by spool size, gas match and how the spool feeds.
Feeding .035 wire without trouble
Most feed trouble starts at the spool or the drive rolls. Check that the spool sits square on the hub and the wire pays off without loops. Too loose and the wire slips, too tight and it flattens, so set the drive roll tension by feel and check the arc. A worn contact tip makes the arc wander, so swap the tip when the arc starts to stutter.
Prep and fit-up
Fit-up is the gap and the alignment of the joint, and the Blue Demon wire is listed for general shop work with poor fit-up. Close the gap, clamp the parts so they cannot move, and clean the joint faces before welding. ER70S-6 deoxidizers help on dirty and rusty steel, per the Sidco listing, but they do not replace cleaning.
MIG fumes and arc flash. MIG welding makes fumes, and galvanized steel makes fumes that need extra care, so weld with good ventilation or outdoors with your head out of the plume, and wear a welding helmet, gloves and a long-sleeve jacket. Keep flammables clear of the work, and secure gas cylinders upright with a chain. See the OSHA welding overview.
FAQ for welders
What gas do I use with .035 ER70S-6 wire?
CO2 or an argon and CO2 mix. The TOOLIOM wire runs on 100% CO2 or a mixed gas of 80% argon and 20% CO2, the Blue Demon wire takes CO2 and/or a CO2 mix, and the Sidco wire takes CO2 or argon/CO2. The PGN listing states no gas, so check the wire label.
Does ER70S-6 wire work on rusty steel?
Yes, within limits. The Sidco wire carries high levels of manganese and silicon deoxidizers that produce welds even on dirty and rusty steel, and the Blue Demon wire is listed for general shop work with poor fit-up. Clean the joint first when you can.
How much wire is on a spool?
The spools here hold 10 lb, 33 lb and 44 lb. The TOOLIOM pack holds two 10 lb spools, the Blue Demon and Sidco spools hold 33 lb each, and the PGN spool holds 44 lb.
Does ER70S-6 wire need gas?
Yes. The Blue Demon wire requires a shielding gas, CO2 and/or a CO2 mix, and the Sidco wire requires CO2 or argon/CO2 shielding gas, which is not included. Solid wire has no flux inside, so the gas does the shielding.
Related: welding consumables, MIG welding wire types, MIG welding wire size, MIG wire spool sizes and MIG welding amperage chart. For machines, see the best welder for beginners.




