MIG Welding Wire Size: Which Diameter to Buy
MIG welding wire size sets how the arc behaves on thin sheet and thicker shop steel, and this guide compares .030 and .035 inch wire so the spool matches the job.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
ARCCAPTAIN Magnesium Aluminum Welding Wire ER5356 .035" MIG9.6/10View on Amazon - 2
TOOLIOM ER4043 .030" Aluminum MIG Welding Wire9.6/10View on Amazon - 3
BIG RED Solid MIG Welding Wire: ER70S-6 .035" 11LBS9.6/10View on Amazon
A patch panel waits on the bench, edges cleaned and clamped, and the weld it needs must lay flat without burning through. On the next bench a gate frame in heavier steel needs a pass with more fill behind it. The wire on the spool decides how either job goes, and mig welding wire size is the choice to get right before striking an arc.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
The short answer on mig welding wire size
The listings in this guide name .030 inch and .035 inch diameters, all in ER70S-6 solid wire. The .035 inch size, listed at 0.9 mm on the Rumvita spool (on Amazon), shows up on the most spools here, in 10 lb and 11 lb sizes and on a 33 lb roll, while the .030 inch size appears on an 11 lb spool from Blue Demon. Thinner wire feeds a smaller puddle that suits thin sheet; thicker wire can carry more metal per pass and suits general shop steel. Match the diameter to the contact tip and the drive rolls, and to the steel in front of you.
Side by side
| .030 inch wire | .035 inch wire | What to check | |
|---|---|---|---|
| Diameter on the label | .030 inch | .035 inch | Match the contact tip and drive rolls |
| Diameter in millimetres | Not stated | 0.9 mm | Check the spool label |
| Wire grade in the listings | ER70S-6 | ER70S-6 | Match the grade to the steel |
| Spool sizes in the listings | 11 lb | 10 lb, 11 lb, 33 lb | Check the spool hub and space in the machine |
| Shielding gas | CO2 or CO2 mix (Blue Demon listing) | 100% CO2 or CO2/Argon mix (Rumvita listing) | Follow the wire listing and the machine manual |
Read the table as a starting point, then check the label on the spool and the chart on the machine door.
When .030 inch wire fits
- Thin sheet and auto body panels. A smaller puddle can mean less burn through on panels with little thickness to spare.
- Home projects and general shop work. The Blue Demon listing calls its .030 inch wire great for home projects and commonly used for general shop applications with poor fit-up.
- Machines set up for .030 inch. The contact tip and drive rolls must match the wire diameter.
- Visible work. Small beads can need less grinding after the weld cools.
Our thinner MIG wire sizes comparison looks at the thinner end of the range.
When .035 inch wire fits
- General shop work and farm repairs. The size suits steel with some thickness behind it, where a pass needs more fill.
- Poor fit-up or rusty, oily plate. The Rumvita listing calls its ER70S-6 wire a fit for general shop work with poor fit-up or rusty, oily plates, with higher levels of manganese and silicon deoxidizers.
- Single-pass and multi-pass welds. The PGN listing states its .035 inch wire supports single-pass and multi-pass welding, with low spatter and precise arc control.
- Longer runs. A 33 lb roll means fewer spool changes on longer runs, where the machine takes that spool size.
See our 030 vs 035 MIG wire guide for a head-to-head on these diameters.
How to tell what your machine takes
Check these before ordering:
- Contact tip. The tip is usually marked with the wire diameter it takes. A tip sized for .035 inch wire gives .030 inch wire a loose fit and an erratic arc.
- Drive rolls. The groove in the roll must match the wire diameter, or the wire slips or jams.
- Spool size. Check the hub and the space inside the machine before ordering a 33 lb roll or a 2-pack of 10 lb spools.
- Wire label. Check the label for the diameter and the grade, and the listing for the shielding gas the wire needs.
Spool sizes: 10 lb, 11 lb and 33 lb
Spool size is a separate choice from wire diameter. The listings here name 10 lb and 11 lb spools, a 2-pack of 10 lb spools, and a 33 lb roll. PGN lists a 10 lb spool of .035 inch wire, BIG RED lists an 11 lb spool of the same diameter, and Blue Demon lists an 11 lb spool of .030 inch wire, while the HYW listing names a 33 lb roll of .035 inch wire.
Solid wire and shielding gas
The listings in this guide are solid ER70S-6 wire, and solid wire needs shielding gas from a cylinder. Blue Demon states its .030 inch wire requires CO2 or a CO2 mix. Rumvita states its .035 inch wire is used with 100% CO2 or a CO2/Argon mix. The HYW listing states its wire conforms to AWS A5.18, with a yield strength of 450 MPa and 30% elongation. Gasless flux core wire shields itself; our gasless vs gas MIG welder guide compares the setups.
For more options, see our welding consumables guides.
FAQ for welders
What mig welding wire size should a beginner start with?
The .035 inch size is a plain starting point for general shop work, since it suits steel with some thickness behind it. For thin sheet and auto body panels, .030 inch wire feeds a smaller puddle, which can mean less burn through. Match the contact tip and drive rolls to the diameter on the spool.
Can .035 inch wire run through a machine set up for .030 inch wire?
Not without changing the setup. The contact tip and the drive roll groove must match the wire diameter, or the wire feeds badly. Swap the tip and rolls for the new size, then check the wire label and the machine manual for the settings that go with it.
Does wire size change the shielding gas?
No. The gas follows the wire type, not the diameter. The Blue Demon and Rumvita listings here name CO2 or a CO2/Argon mix, so pick the gas the wire listing names and keep the cylinder and regulator in order.
What does ER70S-6 mean on a spool?
It is the grade named on the solid wire listings in this guide. The HYW listing states its wire conforms to AWS A5.18, and the Rumvita listing notes higher levels of manganese and silicon deoxidizers than other standard grades of MIG wire.
How much wire comes on a spool?
The listings here name 10 lb and 11 lb spools, a 2-pack of 10 lb spools, and a 33 lb roll, so check the hub and the space inside the machine before ordering.
Related: how to choose a MIG welder, best MIG welding wire, best MIG wire, and the size of welding rod guide. Also see our MIG welder set up guide.




