Flux Core Welding Wire Sizes: Chart and Guide
Flux core welding wire sizes explained by diameter, classification and spool weight, with the listings behind each figure.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
ARCCAPTAIN Flux Core Welding Wire E71T-GS .035" 2LB x 1 Mild9.5/10View on Amazon - 2
TOOLIOM E71T-GS .035" Gasless Flux Core Welding Wire 10LB9.4/10View on Amazon - 3
3 Packs 2-Pound 035 Flux Core Welding Wire9.4/10View on Amazon
A spool change stops the job cold when the wire in the gun does not match the work on the bench. Flux core welding wire sizes are the diameters the wire is sold in, and this guide explains the sizes the listings carry, how the common classifications differ, and how to match the wire to the welder and the joint. Every figure below comes from the listings, not from our own measurements.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Flux core welding wire sizes in the listings
The listings behind this guide carry 0.030 inch and 0.035 inch wire. Both are gasless flux core wire for mild steel, sold on spools, and both run without a shielding gas cylinder. The 0.030 inch listings come from YixangDD and Blue Demon, and the 0.035 inch listings come from Rumvita and KISWEL. Our best flux core wire .030 roundup and our best .035 flux core welding wire roundup score spools in each size.
Diameter is the size that matters at the gun. The drive rolls and the contact tip fit a stated diameter, so the wire on the spool must match the setup in the welder. A listing states its diameter in the title, and the listings here state 0.030 inch or 0.035 inch. Check the diameter on the spool label before loading it, since a spool that looks right can still be the wrong size.
Side by side
| 0.030 inch wire | 0.035 inch wire | Both sizes | |
|---|---|---|---|
| Classification | E71T-GS and E71T-11 | E71T-GS | E71T-GS |
| Spool weight | 2 lb (one listing states 1.8 pounds in its spec table) | 10 lb | 2 lb or 10 lb |
| Shielding | Gasless, self-shielded | Gasless, self-shielded | Gasless, self-shielded |
| Positions | All position, flat, horizontal, vertical upwards, overhead | All position (KISWEL); not stated (Rumvita) | All position (not stated by Rumvita) |
| Passes | Single-pass and multi-pass (YixangDD); multi-pass (Blue Demon) | Single or multi-pass (Rumvita); not stated (KISWEL) | Multi-pass (YixangDD, Blue Demon, Rumvita); not stated (KISWEL) |
| Metals listed | Mild steel, galvanized, stainless | Mild carbon steel (Rumvita); not stated (KISWEL) | Mild steel (not stated by KISWEL) |
| Spool packing | Vacuum-sealed, ABS plastic spool (YixangDD); not stated (Blue Demon) | Vacuum packed, ABS plastic spool (Rumvita); not stated (KISWEL) | Vacuum packing stated by YixangDD and Rumvita only |
The Blue Demon listing states a 2 lb spool in its title and 1.8 pounds in its spec table, so trust the title and treat the spec table weight as the odd figure out. Spool weights are listed as sold, and a 10 lb spool lasts longer between changes than a 2 lb spool on the same work.
E71T-GS vs E71T-11
The listings carry 2 classifications: E71T-GS and E71T-11. E71T-GS is the common gasless flux core wire in these listings, named by YixangDD, Rumvita and KISWEL. Blue Demon names E71T-11 for its 0.030 inch spool. Both classifications are self-shielded, so neither needs an external gas or flux.
The difference the listings state is in passes. E71T-11 is designed for multi-pass operations, and Blue Demon states that it runs on DCEN, direct current electrode negative, in the flat, horizontal, vertical upwards and overhead positions. E71T-GS is listed for single-pass and multi-pass welding, and YixangDD states all-position use. For the full comparison of the classifications, see our 030 vs 035 flux core wire guide.
Classification matters because the listing states what each wire is built for: E71T-11 is designed for multi-pass operations, while E71T-GS is listed for single-pass and multi-pass welding. Read the classification on the label, and run the polarity the wire calls for.
How to match the wire to the job
Start with the machine. The manual states which wire diameters the feeder and drive rolls take, and the listings here state 0.030 inch and 0.035 inch. Set the drive rolls and contact tip to the diameter on the spool, and check the polarity the wire calls for: E71T-11 runs on DCEN. Our flux core welding settings chart lists settings by wire diameter.
Then match the wire to the metal. The listings name mild steel, galvanized steel and stainless steel for 0.030 inch wire, and mild carbon steel for 0.035 inch wire. Blue Demon states its wire is less sensitive to contaminants in the base metal such as rust and mill scale. Clean metal still welds better, so brush the joint before the bead.
Outdoor work favors flux core. YixangDD and Rumvita both state gasless operation for outdoor and windy or drafty conditions, since the flux inside the wire makes its own shielding gas and no cylinder gas can blow away. See our best flux core wire for outdoor use roundup for spools picked for field work.
Spool weights and packing
The listings carry 2 spool weights: 2 lb and 10 lb. YixangDD sells its 0.030 inch wire as a 2 pack of 2 lb rolls, Blue Demon sells a 2 lb spool, and Rumvita and KISWEL sell 10 lb spools. Rumvita states its 10 lb spool as 10 lbs (4.5 kg) with a diameter of .035 inch (0.9 mm). A 10 lb spool suits long runs, while a 2 lb spool suits a small job.
Packing matters because flux core wire hates damp. YixangDD vacuum-seals each roll to keep it waterproof, moisture-proof and dust-proof, and Rumvita vacuum packs its wire the same way. Both makers use ABS plastic spools. Store an open spool dry, and keep the label so the diameter and classification stay with the wire.
What to check before you buy
Read the listing the way you would read a label. Check the diameter, 0.030 inch or 0.035 inch, the classification, E71T-GS or E71T-11, and the spool weight, 2 lb or 10 lb. Check that the wire is gasless and self-shielded when the job has no cylinder, and check the positions the listing states when the work runs vertical or overhead. When a listing leaves a figure unstated, treat it as unstated rather than guessing from another spool.
Flux core smoke and slag. Flux core makes more smoke and fumes than gas MIG, and hot slag can flick off when you chip it. Weld with good ventilation or outdoors with your head out of the plume, wear safety glasses under the helmet when chipping, and clear dry grass and anything flammable from the area. Check the wire label and the machine manual for the polarity and settings before the arc starts.
For more options, see our welding consumables guides.
FAQ for welders
What flux core welding wire sizes are in the listings?
The listings carry 0.030 inch and 0.035 inch wire. The 0.030 inch listings come from YixangDD and Blue Demon, and the 0.035 inch listings come from Rumvita and KISWEL. Both sizes are gasless flux core wire for mild steel.
What is the difference between E71T-GS and E71T-11?
E71T-GS is the common gasless flux core wire in these listings, named by YixangDD, Rumvita and KISWEL. YixangDD and Rumvita list it for single-pass and multi-pass welding. E71T-11 is named by Blue Demon for its 0.030 inch spool, is designed for multi-pass operations, and runs on DCEN in the flat, horizontal, vertical upwards and overhead positions.
Does flux core wire need shielding gas?
No. The wire is self-shielded: the flux inside the wire burns to make its own shielding gas, so no cylinder, hose or regulator is needed. That is why the listings call it gasless, and why it suits outdoor and windy work.
What spool weights do the listings carry?
The listings carry 2 lb and 10 lb spools. YixangDD sells a 2 pack of 2 lb rolls, Blue Demon sells a 2 lb spool, and Rumvita and KISWEL sell 10 lb spools. Blue Demon states 2 lb in its title and 1.8 pounds in its spec table, so trust the title on that spool.
Can 0.035 inch wire run in any flux core welder?
Not always. The machine manual states which diameters the feeder and drive rolls take, and the drive rolls and contact tip must match the diameter on the spool. Check the manual and the spool label before loading the wire, and run the polarity the wire calls for.
Related: gasless vs gas shielded flux core wire, solid wire vs flux core wire, flux core welding pros and cons, flux core vs MIG for outdoor use, and the best MIG welding wire roundup.




