Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Welding Machine for Auto Body Work (2026): 3 Picks Compared

3 welding machines for auto body work compared by process, power, output, rod sizes and warranty.

Best Welding Machine for Auto Body Work (2026): 3 Picks Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1KAISAL JTY-05Best for Auto BodyKAISAL JTY-059.6/10View on Amazon
  2. 2SOARFLY 120ABest Handheld KitSOARFLY 120A9.5/10View on Amazon
  3. 3wuzizi CWM101Best Cordlesswuzizi CWM1019.4/10View on Amazon

A dented door skin or a rusted rocker panel asks for a different welder than a farm gate. Thin sheet burns through fast, and a stud welder pulls a dent without drilling a hole, while a stick welder handles the heavier brackets around it. This guide compares the best welding machine for auto body work options for the home shop, by process, power, output, rod sizes and warranty.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read the affiliate disclosure.

Quick picks

  • Best for Auto Body KAISAL JTY-05: 3500W and 4200A stud welder with 6 modes and a 3 year service term, built for dent repair. Check price on Amazon
  • Best Handheld Kit SOARFLY 120A: 110V 120A ARC welder with 5 level current control, LED display, goggles, helmet and gloves. Check price on Amazon
  • Best Cordless wuzizi CWM101: Battery powered stick welder with 2 20V 8Ah batteries, hot start and anti-stick. Check price on Amazon

The machines

Dent Puller Welder 3500W 4200A Stud Welder Dent

Dent Puller Welder 3500W 4200A Stud Welder Dent

KAISAL9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3500W, 4200A stud welder dent puller with 6 welding modes, auto and manual welding, overheat protection and a 3 year service term, for 110V use.

Pros

  • 6 welding modes for dents of many shapes
  • 4200A output with a current regulation knob from 0 to 4200A
  • Overheat protection with a warning at 158°F
  • 3 year product service stated

Cons

  • Cannot be used on aluminum or hot-rolled sheet
  • Suits only 0.6 to 1.6 mm sheet
  • No stick welding, dent pulling only
  • Stops for a few minutes when the overheat warning trips
Portable Handheld Welding Machine

Portable Handheld Welding Machine

SOARFLY9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A portable handheld 110V 120A ARC stick welder with an IGBT inverter, LED display, 5 level current control, hot start and anti-stick, in a full kit with goggles, helmet, rods, ground wire, gloves and toolbox.

Pros

  • Full kit: goggles, helmet, rods, ground wire, gloves and toolbox
  • 5 level current control with an LED display
  • Hot start and anti-stick for easy ignition
  • Over-voltage, over-current, overload and overheating protection

Cons

  • No warranty term stated
  • No duty cycle stated
  • No second voltage option stated
Cordless Welder Battery Powered Welding Machine

Cordless Welder Battery Powered Welding Machine

wuzizi9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A cordless battery powered stick welder with 2 20V 8Ah batteries, a quick charger, LED display, hot start, arc force and anti-stick, at 8 lb.

Pros

  • Cordless: 2 20V 8Ah batteries, no outlet needed
  • Hot start, arc force and anti-stick
  • LED display shows current and mode
  • 8 lb with a shoulder strap for carrying

Cons

  • No warranty term stated
  • No output amps stated
  • Weight listed as both 8 lb and 3.8 kg, which do not match
  • No duty cycle stated

Other welders and gear to compare

Spec sheet comparison

Model Gear Score Type Power Output Rod sizes Warranty
KAISAL JTY-05 9.6/10 Stud welder dent puller 110V, 3500W 4200A Not stated 3 years
SOARFLY 120A 9.5/10 Handheld ARC stick 110V 120A 1/16 to 1/8 in Not stated
wuzizi CWM101 9.4/10 Cordless stick 2x 20V 8Ah batteries Not stated 1/16 to 5/32 in Not stated

Ratings in this table are the makers’ own claims taken from each product page (11 November 2026). One listing states no output amps, and 2 state no warranty term.

Buying guide: best welding machine for auto body work

Stud welder or stick welder?

A stud welder pulls dents: the KAISAL welds pins and washers to the panel and pulls the dent out, with 6 modes for triangular meson, round meson, OT meson, wave line, carbon rod and single-sided spot welding. A stick welder joins metal: the SOARFLY runs E6013, E6011, E6010, E7018 and E308 rods, and the wuzizi runs 1/16, 3/32, 1/8 and 5/32 in electrodes. For panel dents, the stud welder is the direct pick; for brackets and patches, the stick welders earn their place.

Power and output

The KAISAL and SOARFLY both run on 110V, while the wuzizi runs on 2 20V 8Ah batteries with no outlet in sight. Output sets the work: the KAISAL states 3500W and 4200A, the SOARFLY states 120A, and the wuzizi states no output amps. Match the output to the sheet: the KAISAL suits 0.6 to 1.6 mm cold-rolled sheet.

Thin sheet and heat

Thin body sheet warps under too much heat, so current control matters. The SOARFLY gives 5 level current control with an LED display, and the KAISAL gives a current regulation knob from 0 to 4200A. The wuzizi gives hot start and arc force. The KAISAL listing states it suits iron body parts, galvanized sheets and thin stainless steel sheets, while hot-rolled sheet and aluminum sheets do not suit it.

What comes in the box

The SOARFLY kit includes the machine, auto-darkening goggles, a welding helmet, welding rods, a ground wire, gloves and a portable toolbox. The KAISAL kit includes the dent puller, the welding gun and a set of pull sheets, washers, gaskets, wave lines, carbon rods, hooks and a wrench. The wuzizi kit includes the machine, 2 batteries, a quick charger, a shoulder strap and 2 welding clamp quick plugs.

Warranty

Only the KAISAL states a service term: a 3 year product service. The SOARFLY and wuzizi state no warranty term, so the KAISAL leads on paper for long ownership.

Before You Strike an Arc

  • Check the power: the KAISAL and SOARFLY need a 110V outlet, while the wuzizi needs its 2 20V batteries charged.
  • Match the consumable: E6013, E6011, E6010, E7018 or E308 rods for the SOARFLY, and 1/16, 3/32, 1/8 or 5/32 in electrodes for the wuzizi.
  • Check the sheet: the KAISAL suits 0.6 to 1.6 mm cold-rolled sheet, iron body parts, galvanized sheets and thin stainless steel sheets, not hot-rolled sheet or aluminum.
  • Wear the eye protection in the kit: the SOARFLY includes auto-darkening goggles and a helmet.
  • Galvanized sheet gives off fumes when welded; work with ventilation and keep your head out of the plume.

FAQ for welders

How does a stick welding machine work?

A stick welder runs an electric arc between a coated electrode and the work, melting both into a weld pool. The SOARFLY uses an IGBT inverter to hold a stable arc, with hot start for easy ignition and anti-stick to stop the electrode freezing to the work. The wuzizi runs the same stick process on battery power, with hot start, arc force and anti-stick.

What is an arc welding machine?

An arc welding machine is a welder that joins metal with an electric arc. The SOARFLY and wuzizi here are ARC stick welders: the SOARFLY runs on 110V at 120A, and the wuzizi runs on 2 20V batteries. The KAISAL is a different arc machine, a stud welder that welds pins to a panel for dent pulling.

What rod sizes do these welders take?

The SOARFLY takes rods from 1/16 in to 1/8 in, including E6013, E6011, E6010, E7018 and E308. The wuzizi takes 1/16, 3/32, 1/8 and 5/32 in electrodes. The KAISAL stud welder takes no rods; it welds pins, washers and meson heads to the panel.

Does the dent puller welder work on aluminum?

No. The KAISAL listing states it cannot be used on hot-rolled sheet or aluminum sheets. It suits iron body parts, galvanized sheets and thin stainless steel sheets from 0.6 to 1.6 mm.

What power supply do these welders need?

The KAISAL and SOARFLY run on 110V. The wuzizi runs on 2 20V 8Ah batteries and a quick charger, with no outlet needed.

Related: the welders hub and the stick welders hub. Also see our best spot welder for auto body. Also see our mig vs stick for auto body. Also see our stud welder dent repair kit. Also see our best 6013 welding rod for auto body. Also see our best 6010 welding rod for auto body.

More related guides (6)

Scoring, line by line

Each machine is scored on performance, build, value, safety and warranty, using only what the listing publishes. None states a safety listing, so all score zero on safety. The weights are on the How We Pick page.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
KAISAL JTY-05 9.6 32 22 21 0 3
SOARFLY 120A 9.5 30 21 21 0 0
wuzizi CWM101 9.4 28 20 20 0 0

The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure.

More buying guides