Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Mig vs Tig for Mild Steel: Which One Should You Buy?

Two MIG wires and one TIG rod for mild steel, compared on wire size, gas needs, pack size and the gaps each listing leaves.

Mig vs Tig for Mild Steel: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1ARCCAPTAIN Mild Steel TIG Welding Rod ER70S-6ARCCAPTAIN Mild Steel TIG Welding Rod ER70S-69.4/10View on Amazon
  2. 24-Pack 0.035" Gasless Flux Core MIG Wire4-Pack 0.035" Gasless Flux Core MIG Wire9.4/10View on Amazon
  3. 3LINCOLN ELECTRIC CO ED030631 0.025(0.6 mm)LINCOLN ELECTRIC CO ED030631 0.025(0.6 mm)9.3/10View on Amazon

Verdict: mig vs tig for mild steel. Pick the filler that matches the machine on your bench. The WelderElite example is a gasless flux core MIG wire for outdoor and windy work, the Lincoln example is a 0.025 inch MIG wire aimed at mill scale steel in the shop, and the ARCCAPTAIN example is a TIG rod for careful mild steel fabrication with 100% argon. A wire feeder already in the shop points to the MIG side; a TIG torch with argon on hand points to the rod.

A cracked trailer bracket, a rusted mower deck, a gate hinge that finally gave up. Mild steel is what most home shop repairs are made of, and mig vs tig for mild steel is the question of which wire or rod to feed it. This comparison lines up two MIG wires and one TIG rod, all aimed at mild steel, on what each listing actually states.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

The three picks

ARCCAPTAIN Mild Steel TIG Welding Rod ER70S-6

ARCCAPTAIN Mild Steel TIG Welding Rod ER70S-6

ARCCAPTAIN9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5 lb box of 1/8 inch by 16 inch ER70S-6 mild steel TIG rods, with 100% argon shielding stated in the listing.

Pros

  • 1/8 inch diameter, 16 inch length, ER70S-6 mild steel filler
  • 100% argon shielding gas stated in the bullets
  • Lists stable arc with minimal spatter and smooth, well-formed beads
  • 5 lb pack sized for fabrication and repair work

Cons

  • No warranty term is stated
  • Needs a TIG torch and 100% argon, so the rods are only part of the setup
  • No amperage range or thickness guidance in the listing
4-Pack 0.035" Gasless Flux Core MIG Wire

4-Pack 0.035" Gasless Flux Core MIG Wire

WelderElite9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4-pack of 0.035 inch E71T-GS gasless flux core MIG wire spools, 2 lb each, rated for mild, galvanized and stainless steel.

Pros

  • 0.035 inch E71T-GS flux core wire, no shielding gas needed
  • Suits outdoor and windy work, per the listing
  • Rated for mild steel, galvanized and stainless steel
  • High-strength white ABS spools for storage and use

Cons

  • Listing cautions that stainless steel welds may rust over time
  • No warranty term is stated
  • 8.95 lb package, the heaviest of the three
LINCOLN ELECTRIC CO ED030631 0.025(0.6 mm)

LINCOLN ELECTRIC CO ED030631 0.025(0.6 mm)

Lincoln Electric9.3/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2 lb coil of 0.025 inch (0.6 mm) L-56 mild steel MIG wire, aimed at welding metals with mill scale.

Pros

  • 0.025 inch (0.6 mm) L-56 mild steel wire
  • Aimed at MIG welding on metals with mill scale
  • Claims superior weld appearance and excellent arc characteristics
  • Light 2.1 lb coil, easy to store and carry

Cons

  • Never states gas or gasless, so the setup is unclear
  • No warranty term is stated
  • 2 lb coil is the smallest pack of the three

Other welders and gear to compare

Side by side

ARCCAPTAIN ER70S-6 TIG Rod WelderElite Flux Core MIG Wire Lincoln Electric L-56 MIG Wire
Gear Score 57 56 52
Side TIG MIG MIG
Wire or rod size 1/8 in x 16 in 0.035 in 0.025 in
Pack size 5 lb of rods 2 lb spools, 4-pack per title 2 lb coil
Shielding gas 100% argon None, flux core Not stated
Steel types named Mild and low-alloy Mild, galvanized, stainless Mild steel
Spool or form Straight rods ABS spools Coil
Package weight 5.41 lb 8.95 lb 2.1 lb (table), 2.2 lb (bullets)

Ratings in this table are the makers’ own claims taken from each product page (22 October 2026). None of the three listings states a CSA, UL or ETL listing or a warranty term.

mig vs tig for mild steel: wire and rod size

The WelderElite example is a 0.035 inch flux core wire sold for welding mild steel, galvanized and stainless. The Lincoln example is a 0.025 inch MIG wire the listing aims at metals with mill scale. The ARCCAPTAIN example is a 1/8 inch by 16 inch TIG rod for mild steel fabrication and repair. The listings give no amperage ranges, so match the wire or rod to the machine’s door chart.

Gas or gasless

The WelderElite wire is flux core and needs no shielding gas, which the listing sells as the point for outdoor and windy work. The ARCCAPTAIN rod needs 100% argon, stated right in the bullets. The Lincoln listing is the quiet one: it says MIG wire and names mill scale steel but never says gas or gasless. If the Lincoln is your pick, confirm the gas setup with the seller before you buy. The flux core vs MIG for outdoor use comparison covers the gas question in more depth.

What each side welds

All three name mild steel. The WelderElite listing goes further and names galvanized and stainless too, with the caution that stainless welds may rust over time. The Lincoln listing keeps to mild steel with mill scale. The ARCCAPTAIN listing names low-carbon and low-alloy steels across machinery, auto, bridge, building and pipeline work, which is a broad claim for a 5 lb box of rods. None of the three states a thickness limit, so treat every material claim as bounded by what the listing actually prints.

Pack size and what is in the box

The WelderElite title says a 4-pack of 2 lb spools, though its bullets say two 2-pound spools; the title’s count makes it the biggest supply here, while the bullets’ count would put the ARCCAPTAIN’s 5 lb ahead. It ships on high-strength white ABS spools either way. The Lincoln is a single 2 lb coil, the smallest pack of the three. The ARCCAPTAIN is 5 lb of straight rods, and the welding rod storage picks show how to keep rods dry between jobs. Package weights run 8.95 lb, 2.1 lb and 5.41 lb across the three, straight from the spec tables.

Where the listings go quiet

Three gaps matter. First, the Lincoln spec table lists wire diameter as 0.03 inches against the title’s 0.025 inch; trust the title and bullets, which agree on 0.025 inch (0.6 mm). Second, the WelderElite pack count disagrees with itself, 4-pack in the title against two spools in the bullets. Third, none of the three states a warranty term or a safety listing. What is not stated cannot be compared.

Choose the WelderElite flux core wire if

  • You weld outside or in wind and want to skip the gas bottle.
  • You want multiple spools in a single order.
  • Your work includes galvanized steel as well as mild steel.
  • ABS spools that survive storage matter to you.

Choose the Lincoln L-56 wire if

  • You weld mild steel with mill scale in the shop.
  • You want the thinnest wire of the three.
  • A 2 lb coil is enough for your repair pile.
  • You can confirm the gas setup, since the listing never states it.

Choose the ARCCAPTAIN TIG rod if

  • You have a TIG setup and 100% argon on hand.
  • Your mild steel work is fabrication and repair that rewards a steady hand.
  • You want the clearest spec sheet of the three.
  • Straight rods suit your torch better than a wire feeder.

Before You Strike an Arc

  • Match the filler to the process: flux core wire for gasless wire-feed welding, TIG rod for a TIG torch with 100% argon.
  • Check the wire diameter against the drive rolls and contact tips on hand: 0.035 inch and 0.025 inch each need matching tips.
  • Confirm the Lincoln gas question and the WelderElite pack count with the seller before ordering, since both listings leave them unclear.
  • Store opened wire and rods dry; surface rust on filler shows up as poor arc starts.

FAQ for welders

Can flux core wire weld mild steel?

Yes. The WelderElite example is an E71T-GS flux core wire the listing rates for mild steel, galvanized and stainless, and it needs no shielding gas. That makes it a fit for outdoor and windy work where gas would blow away.

What gas does the ARCCAPTAIN TIG rod need?

The listing states 100% argon. The listing does not name a flow rate, so set it from the machine’s door chart and the joint at hand.

Is the Lincoln L-56 wire gas or gasless?

The listing does not say. It calls the product MIG wire and aims it at metals with mill scale, but the gas question is unanswered. Confirm with the seller before you buy.

Should a beginner pick MIG wire or TIG rod?

The listings do not rank difficulty, so choose by the machine on the bench. A wire feeder takes the MIG wires, a TIG torch takes the rod. Buy the filler that fits the process you already run.

How much wire comes in each pack?

The WelderElite title says four 2 lb spools while its bullets say two, so ask the seller for the real count. The Lincoln is a 2 lb coil and the ARCCAPTAIN is 5 lb of rods, both stated clearly.

Related: flux core vs MIG for outdoor use, best MIG wire for car restoration, MIG vs stick for thick steel, welding rod storage.

Scoring, line by line

The three picks are scored on performance, build, value, safety listing and warranty, with the weights published on the How We Pick page.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
ARCCAPTAIN ER70S-6 TIG Rod 9.4 29 20 20 0 0
WelderElite Flux Core MIG Wire 9.4 28 20 20 0 0
Lincoln Electric L-56 MIG Wire 9.3 27 19 18 0 0

The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure.

Before you strike an arc. Wear a helmet with the right shade for the process and amperage, safety glasses underneath, leather gloves and flame resistant clothing. Weld with good ventilation, clear anything flammable from the area, and keep an extinguisher close. Galvanized steel gives off fumes when welded, so ventilation matters more there. See the OSHA welding overview and the Safety Disclaimer.

More buying guides