Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Use Parts Washer: Step-by-Step Setup

Set the washer on a level spot, fill it with solvent, soak the greasy part and run the pump, then lift the part out to drain before paint or reassembly.

How to Use Parts Washer: Step-by-Step Setup
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1VEVOR Parts Washer 40-Gal 17 Gal Solvent CapacityVEVOR Parts Washer 40-Gal 17 Gal Solvent Capacity9.5/10View on Amazon
  2. 2B’laster Parts Washer – Parts Cleaner SolventB’laster Parts Washer – Parts Cleaner Solvent9.5/10View on Amazon
  3. 3Zep Dyna 143 Parts Washer SolventZep Dyna 143 Parts Washer Solvent9.4/10View on Amazon
  4. 4R19835 PARTS WASHER SOLVENT 5 GAL/PAILR19835 PARTS WASHER SOLVENT 5 GAL/PAIL9.4/10View on Amazon

A greasy gear or a carburetor full of varnish lands on the bench, and a rag barely moves the grime. How to use parts washer comes down to a simple round: set the washer on a level spot, fill it with solvent, lower the part in, let the fluid and the brush do the work, then lift the part out and let it drain. A pump cabinet moves solvent over the part on its own, while a plain tank needs the brush and the soak to do the same job. This guide walks through the setup and the wash, with the gear that fits each step.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

VEVOR Parts Washer 40-Gal 17 Gal Solvent Capacity

VEVOR Parts Washer 40-Gal 17 Gal Solvent Capacity

VEVOR9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 40-gallon steel cabinet washer with an electric pump, mesh filter and gooseneck, rated to support 220 lbs in the tank.

Pros

  • 40-gallon tank with 17 gallon solvent capacity holds large parts
  • Electric pump with mesh filter and gooseneck at 1 gallon per minute
  • Tank supports 220 lbs, so large parts can soak in it
  • Rust- and corrosion-resistant powder coating, with a storage shelf below

Cons

  • No warranty term is stated
  • 92.81 pounds and a 44.49 inch length need a fixed floor spot
  • 40-gallon tank is large for a shop that only washes small parts
  • Electric pump needs power at the wash station
B’laster Parts Washer – Parts Cleaner Solvent

B’laster Parts Washer – Parts Cleaner Solvent

Blaster9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-gallon solvent with a 145°F flashpoint that cleans oil, grease and grime from metals, most plastics and painted surfaces, with no residue.

Pros

  • High flashpoint of 145°F
  • Cleans oil, grease and grime with no residue
  • Works on all metals, most plastics and painted surfaces
  • 5-gallon size fits a bench-top tank or small parts washer

Cons

  • A 5-gallon pail will not fill a 17-gallon solvent capacity
  • Works on most plastics, not all plastics
  • Pail format means lifting and pouring solvent into the tank by hand
  • A 145°F flashpoint still calls for care away from heat and open flame
Zep Dyna 143 Parts Washer Solvent

Zep Dyna 143 Parts Washer Solvent

Zep9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-gallon solvent with a 143°F flashpoint for use in parts washers, made to dissolve grease and oil with low evaporation.

Pros

  • Higher flash point of 143°F than mineral spirits at 107°F
  • Highly-refined, odorless solvents quickly dissolve and flush away grease, oil and other soil
  • Low evaporation rate and vapor pressure mean minimal evaporative loss
  • Recycles continuously in a filtered parts washer, with particulates trapped in filters

Cons

  • Not advisable to use on plastics
  • A 5-gallon bucket will not fill a 17-gallon solvent capacity
  • 143°F flashpoint still calls for care away from heat and open flame
  • Continuous recycling needs a filtered parts washer
R19835 PARTS WASHER SOLVENT 5 GAL/PAIL

R19835 PARTS WASHER SOLVENT 5 GAL/PAIL

Zep9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-gallon pail of cold solvent degreaser for soaking, scrubbing or spraying metal parts, with a citrus fragrance.

Pros

  • Removes tough buildup, oil and grease from metal surfaces
  • Formulated for cold solvent cleaning tanks, no heating needed
  • Suits soaking, scrubbing or spraying
  • Citrus fragrance softens the solvent smell

Cons

  • No warranty term is stated
  • A 5-gallon pail will not fill a 17-gallon solvent capacity
  • Pail format means lifting and pouring solvent into the tank by hand
  • Suits soaking, scrubbing or spraying, but the pail has no pump or flow of its own

How to use parts washer: setup, fill, wash, drain

Start with the washer on a level spot where spills will not reach a drain or open flame. Set the cabinet or tank where the part can go in and out without a long carry, and keep the lid close at hand. Pour in the solvent, then check the fluid level against the pump intake on a cabinet washer so the pump never runs dry. Lower the part into the solvent and let it soak while the grime softens. Run the pump and work the part with the gooseneck flow, or scrub it with a brush in a plain tank. Lift the part out, let it drain back into the tank, and set it aside to dry before the next step, whether that is paint or reassembly.

Solvent in a tank or pump cabinet

Soak in a solvent tank Scrub by hand Pump cabinet washer
How it cleans Parts soak, then get scrubbed by hand Solvent scrubbed or sprayed on by hand Pump moves solvent over the part through a gooseneck
Flow Still solvent, no stated flow rate No flow, applied by hand 1 gallon per minute output flow rate
Tank 5-gallon pails No tank, solvent from the pail 40-gallon tank, 17 gallon solvent capacity
Load Parts that fit the tank Small parts, hand-held Tank supports 220 lbs
Parts it suits Bearings, gears, carburetors and small equipment Tools and small equipment Wheel hub bearings, gears, carburetors, valve assemblies, transmission cases
Flashpoint 145°F (B’laster), 143°F (Zep Dyna 143) 145°F (B’laster), 143°F (Zep Dyna 143) 145°F (B’laster), 143°F (Zep Dyna 143)
Reuse Recycles in a filtered parts washer Solvent used from the pail Mesh filter and pump recirculate the solution

The VEVOR cabinet (on Amazon) in this guide is the pump side of the table, and the solvents are the tank side. A cabinet suits a shop that washes large parts often, while a pail of solvent suits a small tank and a small job. The parts washer tank options run through tank sizes, and the parts washer with filter guide covers filtration.

The gear for this job

The wash needs a tank or cabinet to hold the solvent and a fluid that cuts grease, so the gear below pairs a pump cabinet with the solvents that fill it.

Solvent choice: flashpoint and surfaces

Flashpoint is a number to check when choosing a solvent. B’laster lists 145°F, Zep Dyna 143 (on Amazon) lists 143°F, and the maker notes mineral spirits sits at 107°F, so those two solvents carry a higher margin than mineral spirits. That margin does not make solvent safe near heat: keep the washer away from open flame and heaters, and keep the lid closed when the washer is idle. Surfaces matter as well. B’laster works on all metals, most plastics and painted surfaces, while Zep Dyna 143 is made for metallic parts and the maker says it is not advisable to use on plastics. Match the solvent to the part before the part goes in the tank. The parts washer cleaner guide compares fluid choices in more detail.

Safety in the shop

Fumes and fire are the hazards in this job. Work with ventilation, keep the washer away from ignition sources, and wear eye protection and gloves when handling parts and fluid. Keep a lid on the tank between washes so fumes stay down and dust stays out. Store pails upright with the caps on, and keep rags soaked in solvent out of a pile where heat can build. If a part is coated in unknown grime or old paint, wash it outdoors or with the shop door open and the fan running.

FAQ for welders

How much solvent does a parts washer need?

The VEVOR cabinet in this guide has a 17 gallon solvent capacity, so filling it takes more than a 5-gallon pail. A bench tank takes less, since it only needs enough fluid to cover the part. Check the solvent capacity of the washer at hand and buy pails to match.

Can a parts washer clean plastic parts?

It depends on the solvent. B’laster works on most plastics, while Zep Dyna 143 is not advisable to use on plastics. Check the solvent label for the plastic at hand, and wash a hidden spot to check before the whole part goes in.

Does the solvent need heat?

The Zep R19835 solvent (on Amazon) does not: it is formulated for cold solvent cleaning tanks, with no heating needed. A parts washer heater kit is a separate add-on for shops that want warm fluid.

How does the solvent stay clean?

Use a washer with a filter. The VEVOR pump moves fluid through a mesh filter, and Zep says its solvent recycles continuously in a filtered parts washer while particulates and oils are trapped in filters. Scoop out sludge and change the fluid when it stops cutting grease.

What parts can go in a parts washer?

Metal parts such as wheel hub bearings, gears, carburetors, valve assemblies and transmission cases, plus fuel pumps, filters, master cylinders, valve covers and rocker arms. Keep plastics out unless the solvent lists them, and never wash a part that still holds fuel.

Related: high pressure parts washer, large parts washer, parts washer accessories, parts washer tank options, and the metal fab tools hub. Also see ultrasonic parts cleaner solution.

More buying guides