Parts Washer Heater Kit: Options and Setup
A parts washer heater kit warms the solvent in a parts washer so grease and grime come off faster, and this guide covers heater types, sizing, setup and safety.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
VEVOR 15L Ultrasonic Cleaner9.6/10View on Amazon - 2
VEVOR 6L Ultrasonic Cleaner9.6/10View on Amazon - 3
Jack Boss 3.5 Gallon Capacity Portable Steel Cabinet Parts9.6/10View on Amazon
A greasy gearbox on the bench and a tank of cold solvent that barely cuts the grime. A parts washer heater kit warms the solvent in the washer so grease and oil come off faster and the wash does more of the work. This guide covers what a heater kit is, the types on offer, how to size and fit a heater kit, and the safety checks that matter before you switch it on.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
What a parts washer heater kit is
A parts washer is a tank with a pump that moves solvent over dirty parts. A heater kit adds a heating element to that tank, and a thermostat keeps the solvent warm while you wash. Warm solvent cuts grease faster than cold solvent, which is why shops that clean gearboxes, bearings and carburetors add heat. The kit is the heater and the fittings that hold it in the tank, not a new washer.
Heater types side by side
| Factor | Immersion heater | Band heater | Magnetic heater |
|---|---|---|---|
| Heats | Solvent directly, inside the tank | Tank wall, from outside | Tank wall, from outside |
| Mounting | Drops into the tank | Wraps around the tank | Sits on a flat steel wall |
| Fit | Match the element to the tank | Match the band to the tank | Match the pad to a flat wall area |
| Control | Thermostat, on the kit or separate | Thermostat, on the kit or separate | Thermostat, on the kit or separate |
| Best for | Warming a full tank of solvent | Holding a tank at working warmth | Warming a small tank |
| Watch out for | Never run it dry or uncovered | Needs full contact with the wall | Needs a flat steel wall to grip |
| Cleanup | Lift out to clean the tank | Unwrap to clean the tank | Lift off to clean the tank |
The table above compares the common heater types. Immersion heaters put the element in the solvent, so the heat goes straight into the fluid. Band heaters and magnetic heaters warm the tank wall from outside, so the wall passes the heat to the solvent. Each type needs a thermostat, and each type needs the heater matched to the solvent volume and fitted to the tank it serves.
How to size a heater kit
Start with the tank. The JEGS portable washer (on Amazon) in the reference figures holds a 5-gallon tank with a 3.5-gallon solvent capacity, while the AVGVLIJ washer (on Amazon) is a 3.5-gallon washer with a 110V pump. A bigger tank with more solvent needs a bigger heater, and a small bench washer needs a smaller heater. Match the heater to the solvent volume, not to the tank shell, and check that the element fits inside the tank with the tray or shelf in place. For the washer itself, see the parts washer tank options guide.
Check the power supply too. The reference washers run on 110V, so a heater kit for the same bench needs a mains supply to match. The AVGVLIJ washer lists a 0.7A pump motor with a flow rate of 30 gallons per hour, which shows the scale of a small bench washer: the heater only has to warm the solvent in that tank, not a drum of it.
Setup, step by step
- Place the washer. Set it on a level bench with room around it for parts and for the lid to open.
- Fill the solvent. Fill to the washer’s fill level, and keep the solvent clear of the rim so it does not spill when parts go in.
- Fit the heater. Mount the element where the kit maker says to put it, with the thermostat where it can read the solvent.
- Connect the power. Plug the heater into a mains supply that matches the kit, and keep the cord clear of the solvent and the work.
- Set the thermostat. Set the warmth you want, then let the solvent warm before you start cleaning.
- Keep the lid on. Keep the lid closed while the solvent warms, so the heat stays in the tank.
Safety checks
Heated solvent is a fire risk, so treat the heater with respect. Never run an immersion heater dry or uncovered by solvent, and never leave a heater running with the washer open and unattended. Work with ventilation, keep the washer away from sparks and open flame, and keep a fire extinguisher in the shop. The AVGVLIJ washer lists a hinged lid with a fusible link that closes in a flash fire, which shows the kind of safety feature to look for in a washer.
Heater and solvent safety. Solvent fumes build up in a closed shop, so run the washer with ventilation and keep your head out of the vapor. Wear safety glasses and gloves when handling parts and solvent, and clear anything flammable from the bench. See the OSHA welding overview and the Safety Disclaimer.
FAQ for welders
Can I put a heater in any parts washer?
Only if the washer suits it. The heater must fit the tank and the solvent, and the washer must be built for heated solvent. The reference washers here are steel tanks, a 5-gallon JEGS washer and a 3.5-gallon AVGVLIJ washer, and a heater kit must match the tank it goes in. Check the washer maker’s guidance before fitting a heater.
Does a parts washer heater use much power?
That depends on the kit, and no heater wattage is stated in the reference figures here. The reference washers state a 110V pump, not a heater rating, so read the wattage on the kit itself and check that the shop supply matches it.
Can I heat any solvent in a parts washer?
No. Use only solvent the washer maker approves for heated use, and never heat a solvent that the maker warns against. Keep the lid closed while the solvent warms, and work with ventilation.
What size heater kit do I need?
Match the heater to the solvent volume in the tank. The JEGS washer holds a 3.5-gallon solvent capacity in a 5-gallon tank, and the AVGVLIJ washer is a 3.5-gallon washer, so a kit that suits a small bench washer fits those tanks. A larger tank needs a larger heater.
Do I need a thermostat on a parts washer heater?
Yes. A thermostat holds the solvent at the warmth you set and cuts the heater when it gets there, so the solvent does not keep climbing. A kit without a thermostat leaves the warmth to guesswork, which is a poor setup for heated solvent.
Related: parts washer tank options, parts washer cleaner, table top parts washer, and the metal fab tools hub. Also see the best flux core welder and best welder for beginners guides.




