Table Top Parts Washer: What to Know Before Buying
A table top parts washer cleans small greasy parts on the bench, and this guide covers tank size, pump flow and build before you buy.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
VEVOR Parts Washer 5-Gallon9.5/10View on Amazon - 2
Jack Boss 5 Gallon Capacity Portable Plastic9.4/10View on Amazon
A greasy gear or a gummed-up carburetor sits on the bench, and a rag and a can of cleaner only move the grime around. A table top parts washer gives that job a basin, a pump and a brush or gooseneck, so the cleaning solution does the work while you hold the part. This guide explains what a benchtop washer does, what to check in tank size, pump flow and build, and how the washers in this guide fit a small shop.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

VEVOR Parts Washer 5-Gallon
A steel 5-gallon tank washer with an electric filtration pump and a flexible gooseneck that rinses small parts.
Pros
- Electric filtration pump circulates solution through a mesh filter
- Flexible gooseneck aims flow over part surfaces
- Steel tank with rust-resistant powder coating
- Weighs 15 lbs, so it moves between workshop and garage
Cons
- Solvent capacity is 3.5 gallons in a 5-gallon tank
- No warranty term is stated
- Pump output tops out at 0.4 gallon per minute
- Tank suits small parts, not large cases

Jack Boss 5 Gallon Capacity Portable Plastic
A portable plastic washer that sits on a standard 5-gallon bucket, with a submersible pump and a flow-through brush.
Pros
- Submersible pump with a flow-through hard bristle brush
- Switch on the pump controls flow velocity
- Channel drainage system cycles clean water and catches waste
- Portable, packs up for garage, home or workshop
Cons
- Bucket is not included
- Plastic build, not steel
- Pump flow rate is not stated
- Works only with non-corrosive water-based solutions
What a table top parts washer does
A table top parts washer is a small basin with a pump that moves cleaning solution over a dirty part. You set the part in the tank or bucket, switch the pump on, and the solution flows over the surface while a brush or a gooseneck aims it where the grime sits. Loosened grease drains back into the tank or bucket, and the pump sends the solution around again. The washers in this guide are built for small parts and tools: wheel hub bearings, gears, carburetors, valve assemblies and transmission cases are the parts the VEVOR listing names. That size suits bench work, where the part comes off the machine and goes into the tank, rather than whole assemblies that stay bolted in place. A benchtop washer also keeps the mess contained, instead of spreading dirty rinse water across the bench.
Side by side
| Washer | Tank | Pump | Build | Warranty |
|---|---|---|---|---|
| VEVOR 5-Gallon Parts Washer | 5 gallon | 0.4 gallon per minute max, electric filtration pump | Steel with powder coating | Not stated |
| Jack Boss 5 Gallon Parts Washer | 5 gallon | Submersible pump with flow-through brush | Plastic | One-year warranty |
The VEVOR washer lists a 3.5-gallon solvent capacity inside its 5-gallon tank, with pump output up to 0.4 gallon per minute. The Jack Boss washer (on Amazon) fits a standard 5-gallon bucket and runs its pump through a flow-through brush, with no flow rate stated. Both are rated at 5 gallons, so the choice comes down to the basin and the way the solution reaches the part.
Table top parts washer picks for the bench
Cleaning small parts comes down to tank room and pump flow, and the washers below cover that job from both sides: a steel tank with a gooseneck that rinses parts under flowing solution, and a plastic washer that sits on a bucket and scrubs with a brush.
What to check before buying
- Tank size. Both washers in this guide are rated at 5 gallons, which sets the size of the parts that fit. Measure the largest part you clean before choosing.
- Pump flow. The VEVOR washer lists pump output up to 0.4 gallon per minute through a flexible gooseneck. The Jack Boss washer uses a switch on the pump to control flow velocity through its brush.
- Solvent capacity. The VEVOR tank holds 5 gallons, with solvent capacity listed at 3.5 gallons.
- Build. The VEVOR tank is steel with a rust-resistant powder coating. The Jack Boss washer is plastic and sits on a bucket you supply.
- Cleaning solution. The Jack Boss washer is made for non-corrosive water-based cleaning solutions. Match the solution to the washer, and do not mix solution types.
- Weight and portability. The VEVOR washer weighs 15 lbs, so it moves between workshop and garage. The Jack Boss washer packs up for the garage, home or workshop.
- Warranty. The Jack Boss washer carries a one-year warranty. The VEVOR washer states no warranty term.
A benchtop washer is a cleaning aid, not a degreasing line. Parts with caked-on dirt still need the brush or the gooseneck aimed at them, and the solution still needs changing when it turns dark.
How to use a table top parts washer
Set the washer on a steady bench and add the cleaning solution the washer is made for: a non-corrosive water-based solution for the Jack Boss washer. Set the part in the tank or bucket and switch the pump on. On the VEVOR washer, aim the gooseneck over the dirty faces. On the Jack Boss washer, work the flow-through brush over them and use the switch on the pump to set the flow, and let its channel drainage catch waste and cycle clean water back through. Lift the part out, check the faces, and run it through again if grime stays in the corners. Work with the washer where spills stay off the bench.
FAQ for welders
What size parts fit a table top parts washer?
Small parts and tools fit, such as wheel hub bearings, gears, carburetors, valve assemblies and transmission cases, which the VEVOR listing names. Both washers in this guide are rated at 5 gallons, so a part has to fit inside the tank or the bucket. Larger cases and assemblies need a bigger washer or a different cleaning method.
What cleaning solution does a table top parts washer need?
The Jack Boss washer is made for non-corrosive water-based cleaning solutions, and its pump and brush are built around that kind of fluid. The VEVOR washer circulates its cleaning solution through a mesh filter before it reaches the gooseneck. Match the solution to the washer, and do not mix solution types.
Can a table top parts washer clean a carburetor?
Yes, the VEVOR listing names carburetors among the parts its washer cleans, along with gears and wheel hub bearings. Set the carburetor in the tank, run the pump, and aim the gooseneck over the dirty faces. Small passages may still need hand work after the wash.
Steel or plastic: which tank build suits a home shop?
The VEVOR washer uses a steel tank with a rust-resistant powder coating, and the listing says it moves between workshop and garage. The Jack Boss washer is plastic, fits a standard 5-gallon bucket, and packs up to move between garage, home and workshop. Choose steel for a bench washer with a pump and filter, and plastic when the washer has to pack up and travel.
Related: parts washer ultrasonic, and the metal fab tools hub.




