Industrial Parts Washers: Features to Compare
An industrial parts washer cleans greasy shop parts in a tank of cleaning solution, and tank size, pump flow, power and safety features decide which washer fits the shop.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Jack Boss 3.5 Gallon Capacity Portable Steel Cabinet Parts9.6/10View on Amazon - 2
Parts Washer [20-Gallon Tank]9.5/10View on Amazon - 3
VEVOR Parts Washer 5-Gallon9.5/10View on Amazon
A greasy gearbox, a carburetor caked in old fuel varnish, a batch of brackets fresh off the mill: all of them need to be clean before paint, assembly or a weld repair, and scrubbing each piece by hand eats shop time. An industrial parts washer cleans parts in a tank of cleaning solution, either with a pump that circulates solution over the part or with ultrasonic waves in the solution, so grease, oil, chips and grime come off in the tank instead of on the bench. This guide covers the types, sizes, pump and power figures, and safety features to compare before buying.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
How an industrial parts washer works
A parts washer holds cleaning solution in a tank and cleans the part in that solution. In a cabinet washer, an electric pump pushes solution through a flexible spout or gooseneck while the part sits on a tray or shelf, and a brush takes off what stays stuck. Eastwood’s instructions finish with a rinse in warm water. In an ultrasonic washer, the part sits in a heated tank while transducers send sound waves through the solution, reaching blind holes and internal cavities that a brush cannot reach. The AFF washer (on Amazon) takes water based cleaning solutions with a pH of 7 to 8 only, so check the fluid the maker allows before filling any washer.
Types of industrial parts washers
Cabinet solvent washers are a common shop type: a steel tank, a pump, and a hinged lid that closes over the work. They suit tools, gears, bearings and automotive components, and they range from benchtop units to floor standing cabinets.
Ultrasonic washers clean with sound instead of flow. The MechMaxx UC32 (on Amazon) pairs a 32 gallon tank with 28kHz sound, 20 transducers and a 6.6kW heater, and it suits CNC machined parts, electronic parts and injection molded components. It fits precision parts, but it runs on 208 to 240V, 3 phase power, which many small shops do not have.
Benchtop washers are the small end of the range. The BIG RED T10035 (on Amazon) holds 3.5 gallons and runs a 325 gallon per hour pump on 110V, and its work basin measures 18 inches wide by 13.5 inches deep and 9 inches high. A benchtop unit fits small parts cleaning jobs like wheel bearings, gears and carburetors, and it moves around the shop more easily than a floor cabinet.
Side by side
| Cabinet solvent washer | Ultrasonic washer | Benchtop washer | |
|---|---|---|---|
| Cleaning action | Pump circulates solution over the part | Sound waves in a heated tank | Pump circulates solution over small parts |
| Tank size in the listings | 40 gallon (Eastwood and AFF) | 32 gallon (MechMaxx UC32) | 3.5 gallon (BIG RED and Homak) |
| Pump flow in the listings | 5.3 gallons per minute (Eastwood) | No pump, 20 transducers (MechMaxx UC32) | 325 gallons per hour (BIG RED) |
| Power in the listings | 110V and 120V | 208 to 240V, 3 phase (MechMaxx UC32) | 110V (BIG RED) |
| Suits | Tools and automotive components | CNC parts and precision parts | Bearings, gears and carburetors |
| Watch for | Flammable solvent limits | Needs 3 phase power | Small work basin |
The right type follows the parts: big, greasy shop parts suit a cabinet washer, precision parts with blind holes suit ultrasonic cleaning, and small parts suit a benchtop unit that holds the largest part the shop cleans.
Tank size and working capacity
Tank size and working capacity are different figures. The Eastwood washer (on Amazon) holds 40 gallons in the tank, while the AFF washer holds 40 gallons with a 22 gallon working capacity, so check the working capacity, not just the tank size. Depth matters too: the Eastwood tub is 10 inches deep, and the maker says the oversize tub accepts larger parts and allows longer fluid life. Measure the largest part the shop cleans, then compare it with the basin: the BIG RED basin measures 18 inches wide by 13.5 inches deep and 9 inches high, and the Homak washer (on Amazon) measures 17.0 inches by 13.5 inches by 9.0 inches overall. The Homak washer holds 3.5 gallons, and the AutoForever washer holds a 20 gallon tank with a 12 gallon solvent capacity.
Pump flow and cleaning action
Pump flow decides how fast solution moves over the part. The Eastwood pump moves 5.3 gallons per minute, the AFF pump moves 50 gallons per hour, and the AutoForever listing states approximately 50 gallons per hour and also lists a max pump output of 318GHP. The Homak pump moves 0.6 gallons per minute at its maximum flow rate. Flow alone does not clean a part: the Eastwood gooseneck bends so solution flows completely over the part surface, and the maker says to allow time for the solution to soften grease and debris before brushing off stubborn deposits. The AFF washer adds a flexible delivery spout, a removable work shelf, a parts basket and a cleaning brush, and the MechMaxx ultrasonic washer comes with two stainless steel cleaning baskets.
Power supply
The cabinet and benchtop washers in these listings run on a standard shop outlet. The Eastwood and AutoForever washers run on 120V, and the BIG RED and AFF washers run on 110V. The AFF washer includes a safety GFCI plug at 110V and 0.5A. The MechMaxx UC32 is the exception: it runs on 208 to 240V, 3 phase power and carries a 6.6kW heater, so it needs a supply the shop may have to install.
Safety features to look for
A parts washer holds cleaning solution near heat and electricity, so the safety features deserve the same attention as the tank. Look for a hinged lid with a fusible link that closes when not in use and helps prevent accidental fire: the BIG RED and Homak washers state a fusible link lid, and the AFF heat-resistant cover with a fuse closes automatically. The Eastwood safety information warns to read all instructions, since failure to follow them may result in electric shock, fire or serious injury.
The AFF washer is UL Listed on the complete unit and cETL certified to CAN/CSA C22.2 No. 68-92, and it includes a safety GFCI plug. The BikeMaster washer is UL and SAA Certified. The BIG RED washer is not for use with flammable or combustible solvents such as mineral spirits and biodegradable cleaners, and the AFF washer takes water based cleaning solutions with a pH of 7 to 8 only. Work with the lid closed when the washer is idle, keep the area ventilated, and follow the fluid limits the maker states for that unit.
Choosing the right washer for the shop
Start with the largest part and the dirtiest job, then work back to the washer. A shop that cleans gearboxes and automotive components points to a cabinet with a deep tub and a strong pump, a shop that cleans precision parts with blind holes points to ultrasonic cleaning, and a bench with small parts points to a benchtop washer that fits the bench and the outlet nearby. Weight and footprint decide where the washer lives: the Eastwood washer weighs 92.4 pounds and measures 35 inches by 21.5 inches by 43 inches, the AFF washer weighs 106 pounds and measures 45 inches by 21.25 inches by 35.625 inches, and the BIG RED benchtop washer weighs 16.8 pounds and measures 18.5 inches by 14.17 inches by 9.84 inches. The Eastwood washer comes with a 1-year limited warranty and a 90-day return, and the BIG RED washer includes a 1 year limited manufacturer warranty.
FAQ for welders
What size industrial parts washer do I need?
Size follows the largest part the shop cleans. Measure that part, then compare it with the basin and the working capacity. A 40 gallon cabinet suits large tools and automotive components, a 20 gallon cabinet like the AutoForever holds a 12 gallon solvent capacity, and a 3.5 gallon benchtop washer suits small parts like bearings, gears and carburetors.
Can I use mineral spirits in a parts washer?
Only if the maker says so for that unit. The BIG RED washer is not for use with flammable or combustible solvents such as mineral spirits, and the AFF washer takes water based cleaning solutions with a pH of 7 to 8 only. Always check the fluid limits the maker states before filling the washer.
How does an ultrasonic parts washer clean?
An ultrasonic washer sends sound waves through heated solution in a tank, and the waves reach complex shapes, blind holes and internal cavities that a brush cannot reach. The MechMaxx UC32 uses 28kHz sound and 20 transducers in a 32 gallon tank, and it suits CNC machined parts, electronic parts and injection molded components.
What power supply does an industrial parts washer need?
The cabinet and benchtop washers in these listings run on 110V or 120V: the BIG RED and AFF washers run on 110V, while the Eastwood and AutoForever washers run on 120V. The MechMaxx ultrasonic washer is the exception, running on 208 to 240V, 3 phase power. Check the voltage and the plug before ordering.
Do parts washers need ventilation?
Yes, in practice. Cleaning solution can give off fumes. Work in a ventilated area, keep the lid closed when the washer is idle, and keep flammable material away. The guide on how to clean parts safely in the shop covers the full routine.
Related: how to use a parts washer, parts washer portable, parts washer ultrasonic, ultrasonic cleaner sizes, high pressure parts washer, parts washer tank options, and the metal fab tools hub.




