Drilling Size for M8 Tap: How to Pick the Bit
The drilled hole for a metric tap starts smaller than the thread, and the right bit follows from the tap marking and a tap drill chart. How to find the size, pick a metric bit, and drill and tap cleanly.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
MACXCOIP Metric 25Pcs9.6/10View on Amazon - 2
Drill America 25 Piece Metric Killer Force Drill Bit Set in9.6/10View on Amazon - 3
Hymnorq 15-Piece M35 Cobalt Drill Bit Set9.6/10View on Amazon
A bracket on the bench needs a threaded hole, and the drilled hole has to leave room for the tap to cut threads. Drill too wide and the tap has nothing to bite. Drill too narrow and the tap binds, squeals and snaps. This guide covers the drilling size for m8 tap work: how to find the right bit, how to read a metric set, and how to drill and tap the hole cleanly.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Why the drilled hole is smaller than the tap
A tap does not push metal aside. It cuts threads into the wall of a drilled hole, so the hole starts smaller than the finished thread. The drilled diameter leaves a ring of metal for the tap teeth to shape into thread crests and roots. If the hole matches the full thread diameter, the tap passes through without cutting a usable thread. If the hole is far under size, the tap has to remove too much metal at once and torque climbs fast. That is why every tap size pairs with a smaller drill size, and why guessing from the bolt alone gets people in trouble.
The tap itself carries the clue. Metric taps are marked with the thread size and pitch on the shank. The pitch tells you how far apart the threads sit, and the drill size follows from the pair. Read the marking before you pick a bit, because coarse and fine threads in the same diameter call for different drilled holes. Our what is tapping guide explains how taps cut threads and what the markings mean.
Finding the drilling size for m8 tap
Start with the tap in hand, not with the bolt. Read the size and pitch marked on the tap shank, then match that pair on a tap drill chart. The chart gives the drilled diameter that leaves the right amount of metal for that thread. The tapping drill chart and the drilling and tapping chart walk through reading the rows and columns without guessing.
Next, find that diameter in a metric drill bit set. Metric sets step through small sizes in fine increments, which matters here because tap drill sizes fall between whole millimeter marks. Drill America states metric sizes ranging from 1mm to 13mm by 0.5mm in its 25 piece cobalt set. HYMNORQ states 19 metric drill bits from 1.0mm to 10.0mm in 0.5mm increments. toolant states a 19 piece metric set covering 1mm to 10mm. A set with fine steps gives you a bit at or near the chart size instead of forcing a jump to the next whole size.
Check the bit marking against the case index before you chuck it. Bits roll, cases get mixed, and a worn marking is easy to misread under shop light. If the chart size falls between bits you own, follow the tap maker’s chart guidance for your material rather than rounding on your own. Hard material and soft material do not always take the same drilled hole, so the right size can shift with the material.
Metric sets side by side
| Set | Sizes stated | Point angle | Material stated |
|---|---|---|---|
| Drill America 25 Piece Metric Cobalt | 1mm to 13mm by 0.5mm | 135 degree split point | Cobalt |
| toolant 19Pcs Metric | 1mm to 10mm | 135 degree self centering point | M35 cobalt steel |
| HYMNORQ 19-Piece Metric HSS | 1.0mm to 10.0mm in 0.5mm increments | 118 degree point angle | High speed steel |
| PLATINUMEDGE Metric 99 Pieces Titanium | 1.5mm up to 10mm | 135 degree tip | High speed steel, titanium coated |
Sizes, angles and materials above come from the makers’ stated figures for each set. The cobalt sets here state hard metal as their use, while the HYMNORQ high speed steel set states wood, plastic and soft metal. Match the bit material to the workpiece, not just the diameter.
Picking a bit from a metric set
Point angle matters on the bench. Many sets in this group state a 135 degree point. DEWALT states 135 degree split point tips that drill on contact and help prevent walking on hard surfaces. toolant states a 135 degree self centering point that starts without wandering. HYMNORQ states a 118 degree point angle with a straight round shank. A split point starts cleaner on flat stock, which helps when the hole location has to land on a layout mark.
Shank style is simple here. Straight shank jobber bits fit standard drill chucks. WildBossy and HYMNORQ state straight shank designs. Keep the bit short in the chuck, with enough flute showing to clear chips, and check runout by eye before you drill. A bent bit drills an oversize, wobbling hole, and no tap fixes a wobbled hole. Our best drill bit set for hard steel guide compares cobalt and high speed steel sets for metal work.
Material choice follows the workpiece. Drill America states its m35 cobalt drills suit tough, high tensile strength materials such as stainless steel and titanium, as well as wood and plastic. HYMNORQ states its high speed steel bits suit wood, plastics and thin soft metal sheets, and notes hard steel and thick iron plate as poor fits. Read the stated material range before you drill, because a bit that dulls halfway leaves a tapered hole that taps poorly.
Drilling the hole
Clamp the work. A drill press vise or a solid clamp on the bench keeps the part from spinning when the bit breaks through. Mark the hole location, center punch the mark, and start with a small pilot hole when the final size is large or the surface is curved. WildBossy states for stainless steel and hard metal to use low speed, steady pressure, and cutting oil or lubricant, and to start with a smaller pilot hole when needed. Keep the bit aligned with the hole, ease off as the bit breaks through, and clear chips often so the flutes do not pack.
Drill through with the part backed up when you can. A backing board or a sacrificial block under thin stock keeps the exit side cleaner and stops the bit from grabbing at breakthrough. Check the drilled hole with the tap held beside it before you cut threads. The tap should look larger than the hole, with the thread crests standing proud of the drilled diameter.
Tapping after drilling
Chamfer the hole edge lightly so the tap starts straight. Add cutting fluid made for tapping, set the tap in a tap wrench, and turn with steady pressure, backing off often to break chips. Keep the tap square to the surface for the first turns, checking from two sides, because a crooked start stays crooked. Our best tapping fluid guide covers fluids for clean threads, and our best tap wrench guide covers wrenches and sets.
If the tap squeals, binds hard, or needs heavy force, stop. Back it out, clear chips, add fluid, and check that the drilled hole matches the chart for that tap. Forcing a tap in an undersize hole breaks taps, and a broken tap in a finished part is a bad day. A slightly larger drilled hole from the chart range beats a snapped tap.
Drilling and tapping safety. Wear eye protection for drilling and tapping, clamp the work so it cannot spin, and keep hands, gloves and loose clothing away from rotating bits and chucks. Let hot chips cool before you brush them away, and use a brush rather than bare hands. See our Safety Disclaimer for shop safety basics.
FAQ for welders
How do I find the drill size for a metric tap?
Read the size and pitch marked on the tap shank, then match that pair on a tap drill chart. The chart gives the drilled diameter for that thread. Pick the matching bit from a metric set, such as the Drill America set stated from 1mm to 13mm by 0.5mm.
Can I drill the hole the same size as the tap?
No. A hole at full thread diameter leaves no metal for the tap to cut, so the finished thread has no grip. The drilled hole always starts smaller than the tap, with the difference set by the thread pitch on the chart.
What if my set has no bit at the chart size?
Use a set with fine steps, such as the HYMNORQ set stated in 0.5mm increments or the toolant set covering 1mm to 10mm. If the chart size still falls between bits, follow the tap maker’s chart guidance for your material instead of rounding on your own.
Which bit material suits steel?
Cobalt sets suit harder metal. Drill America states its m35 cobalt drills suit stainless steel, titanium and other hard metals. HYMNORQ states its high speed steel bits suit wood, plastic and soft metal, and notes hard steel as a poor fit.
Why did my tap break?
Common causes are an undersize drilled hole, a crooked start, packed chips and dry cutting. Back the tap out often to break chips, keep cutting fluid on the tap, and confirm the drilled diameter against the chart for that tap before you start.
Related: drilling size for m6 tap, drill index sizes, best drill bit to drill through metal, and the metal fab tools hub. Also see our how to insert a drill bit guide.




