Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Drilling Size for M6 Tap: 5mm Tap Drill Size

The drilling size for an M6 tap is 5mm, and four metric drill bit sets are compared below, three with a stated 5mm bit and one with a stated range only.

Drilling Size for M6 Tap: 5mm Tap Drill Size
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1MACXCOIP Metric 25Pcs(1.0mm-13.0mm)MACXCOIP Metric 25Pcs(1.0mm-13.0mm)9.6/10View on Amazon
  2. 2Drill America 25 Piece Metric Killer Force DrillDrill America 25 Piece Metric Killer Force Drill9.6/10View on Amazon
  3. 3Hymnorq 15-Piece M35 Cobalt Drill Bit SetHymnorq 15-Piece M35 Cobalt Drill Bit Set9.6/10View on Amazon
  4. 4Makita B-49373 75 PC Metric Drill and Screw BitMakita B-49373 75 PC Metric Drill and Screw Bit9.6/10View on Amazon

This guide covers drilling size for m6 tap. A tapped hole starts with the right drill bit: too small and the tap binds, too large and the thread has nothing to grip. The drilling size for an M6 tap is 5mm. For a standard coarse M6 tap, drill the hole with a 5mm bit and then cut the thread with the tap. Three of the sets in the gear section below state a 5mm bit in the box; the Makita set states a 1mm to 8mm range for its drill bits without listing the individual sizes, so a 5mm bit is not confirmed there.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

MACXCOIP Metric 25Pcs(1.0mm-13.0mm)

MACXCOIP Metric 25Pcs(1.0mm-13.0mm)

MACXCOIP9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 25-piece M35 cobalt metric set from 1mm to 13mm in a metal storage box, with a 135 degree point tip for self-centering starts.

Pros

  • M35 cobalt bits for stainless steel, cast iron, copper and aluminum
  • Full 1mm to 13mm range by 0.5mm, including the 5mm bit
  • 135 degree point tip for self-centering and fast chip removal
  • Metal storage box with size indexes

Cons

  • Not for quenched bolts
  • No warranty term stated
  • Range stops at 13mm, so larger holes need another set
  • Metric sizes only, with no imperial bits in the box
Drill America 25 Piece Metric Killer Force Drill

Drill America 25 Piece Metric Killer Force Drill

Drill America9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 25-piece M2 high speed steel metric set from 1mm to 13mm in a round case, with a 135 degree split point for self-centering starts.

Pros

  • M2 premium grade high speed steel with a gold and black finish
  • Full 1mm to 13mm range by 0.5mm, including the 5mm bit
  • 135 degree split point for self-centering and fast precision drilling
  • Round shanks fit many tool holding systems

Cons

  • No warranty term stated
  • Range stops at 13mm, so larger holes need another set
  • Metric sizes only, with no imperial bits in the box
  • Plastic storage holder case rather than a metal box
Hymnorq 15-Piece M35 Cobalt Drill Bit Set

Hymnorq 15-Piece M35 Cobalt Drill Bit Set

HYMNORQ9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 15-piece M35 cobalt metric set from 1.5mm to 10mm in a rugged ABS indexed case, with a 135 degree split point that, per the maker, needs no pre-punch pilot hole.

Pros

  • True M35 cobalt steel with 5% cobalt for heat resistance
  • Fully ground bits for dimension accuracy and concentricity
  • 135 degree split point prevents walking with no pre-punch pilot hole
  • Rugged ABS case with rubberized corners and raised size indexes

Cons

  • Range runs 1.5mm to 10mm, so no bits above 10mm
  • 15 pieces against 25 in the larger metric sets
  • No 1mm bit; the smallest size is 1.5mm
  • ABS plastic case rather than a metal box
Makita B-49373 75 PC Metric Drill and Screw Bit

Makita B-49373 75 PC Metric Drill and Screw Bit

Makita9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 75-piece metric drill and screw bit set with 19 titanium nitride coated HSS drill bits from 1mm to 8mm, plus insert and power bits for fastening.

Pros

  • 19 titanium nitride coated HSS drill bits for metal and wood
  • 4 brad point wood bits from 4mm to 8mm
  • Insert and power bits for Phillips, Pozidriv, Torx, slotted and hex fasteners
  • 75 pieces in one set for drilling and fastening

Cons

  • Drill bits stop at 8mm, so no 10mm or 13mm sizes
  • No cobalt bits for hardened stainless work
  • Point angle is not stated, so self-centering is not promised
  • 4 brad point bits are for wood, not metal

The drilling size for m6 tap

A standard coarse M6 tap has a 1.0mm pitch, so the tap drill is 5mm: 6mm minus 1.0mm leaves the right amount of material for the thread to cut into. Drill the hole with the 5mm bit, keep the drill square to the work, and clear the chips before the tap goes in. The chart below states the size for a standard coarse M6 tap.

Tap Pitch Tap drill
M6 coarse 1.0mm 5mm

Side by side

Drill America KFD MACXCOIP M35 Hymnorq M35 Makita B-49373
Sizes 1mm to 13mm by 0.5mm 1mm to 13mm by 0.5mm 1.5mm to 10mm 1mm to 8mm HSS bits
Material M2 high speed steel M35 cobalt M35 cobalt, 5% cobalt Titanium nitride coated HSS
Point 135 degree split point 135 degree point tip 135 degree split point Not stated
Case Round case Metal storage box ABS indexed case Not stated
Pieces 25 25 15 75

All four sets are metric. Three of them state a 5mm bit in the box; the Makita set states a 1mm to 8mm range for its drill bits without listing the individual sizes, so a 5mm bit is not confirmed there. The two 25-piece sets run 1mm to 13mm, the Hymnorq set runs 1.5mm to 10mm, and the Makita set runs 1mm to 8mm for its drill bits. M35 cobalt appears in the MACXCOIP and Hymnorq sets, M2 high speed steel in the Drill America set, and titanium nitride coated HSS in the Makita set.

How to drill the tap hole

Mark the hole position and start the bit with its split point on the mark: the 135 degree split points on the Drill America, MACXCOIP and Hymnorq bits are stated to self-center, so the bit starts on the mark instead of wandering across the work. Drill the hole with the 5mm bit and clear the chips, then cut the thread with the tap, backing it off to break the chip. Use cutting fluid on steel to keep the tap from binding.

The gear: drill bit sets for the 5mm hole

The 5mm bit does the drilling, so the set you pick needs that size in the box with a point that starts true.

FAQ for welders

What size drill bit do I need for an M6 tap?

You need a 5mm drill bit. A standard coarse M6 tap has a 1.0mm pitch, so the tap drill is 5mm: 6mm minus 1.0mm. Three of the sets in the gear section state a 5mm bit in the box; the Makita set states a 1mm to 8mm range without listing the individual sizes, so check that a 5mm bit is in the box before relying on it.

Can I use a 5.5mm drill bit for an M6 tap?

A 5.5mm bit drills a larger hole than the 5mm tap drill, so the thread it cuts has less material to grip. The MACXCOIP and Drill America sets include both 5mm and 5.5mm bits, so the 5mm bit is in the box. Use the 5mm bit for a standard coarse M6 tap.

Do I need a pilot hole before the 5mm bit?

Not with the split point bits here. The Hymnorq 135 degree split point bites on contact and, per the maker, eliminates the need for a pre-punch pilot hole, and the Drill America and MACXCOIP bits state self-centering points as well. The Makita set states no point angle, so it makes no such claim. Mark the spot and drill the hole with the 5mm bit.

What drill bits work for stainless steel?

M35 cobalt bits suit stainless steel: the MACXCOIP set lists stainless steel, iron castings, copper and aluminum, and the Hymnorq set lists stainless steel, cast iron and titanium alloys. The Drill America M2 high speed steel set is also rated for stainless steel and other hard metals. Pick the cobalt sets for the hardest stainless work.

Related: metal fab tools hub, best drill bit for stainless steel, best tap wrench, drilling and tapping chart, and what is tapping.

More buying guides