Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Anvil for Blacksmithing (2026): 5 Picks Compared

Cast steel and cast iron anvils for blacksmithing, from 9 to 132 lbs, compared on weight, hardness, rebound, work surface, holes and warranty.

Best Anvil for Blacksmithing (2026): 5 Picks Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Easmvetaln 132 lbBest OverallEasmvetaln 132 lb9.7/10View on Amazon
  2. 2VEVOR 116 lbLargest Work SurfaceVEVOR 116 lb9.6/10View on Amazon
  3. 3VEVOR 22 lbBest Small AnvilVEVOR 22 lb9.6/10View on Amazon
  4. 4Olympia 9 lb HobbyBest Hobby AnvilOlympia 9 lb Hobby9.4/10View on Amazon

A hot bar on the anvil, a hammer in hand, and a face that bounces the blow back into the steel: that is the work an anvil does. This best anvil for blacksmithing guide compares the anvils below on what each listing states: weight, material, hardness, work surface, holes and warranty. The heaviest cast steel anvils suit full-size forging, while the hobby anvil suits small tasks at the bench.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall Easmvetaln 132 lb: 132 lbs of cast steel at 55HRC with a rebound rate over 70% and a 13.58 by 3.94 inch work surface. Check price on Amazon
  • Largest Work Surface VEVOR 116 lb: A 22.5 by 3.9 inch working surface on a 116 lb cast steel anvil with a cutting table and hardy hole. Check price on Amazon
  • Best Small Anvil VEVOR 22 lb: A 22 lb cast steel anvil at 50HRC with a rebound rate over 70%, round and square holes, and a bench-clamp base. Check price on Amazon
  • Best Hobby Anvil Olympia 9 lb Hobby: A 9 lb cast iron hobby anvil with a 5-1/2 by 2 inch face, a 3-1/2 inch horn and a Limited Lifetime warranty. Check price on Amazon

The machines

Easmvetaln Cast Steel Anvil,132 Lbs(60kg)

Easmvetaln Cast Steel Anvil,132 Lbs(60kg)

Easmvetaln9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 132 lb cast steel single horn anvil with a 55HRC face, a rebound rate over 70% and a 13.58 by 3.94 inch work surface.

Pros

  • 55HRC hardness from an 800 degree heat treatment, the highest stated here
  • Rebound rate over 70% stated
  • 13.58 by 3.94 inch work surface
  • Round and square holes plus a filleted corner for fitting, punching and bending

Cons

  • No warranty term stated
  • No cutting table stated, unlike the 116 lb VEVOR
  • No stand or mounting hardware is stated
  • 132 lbs, the heaviest anvil in this set
VEVOR Single Horn Anvil, 116lbs Cast Steel Anvil

VEVOR Single Horn Anvil, 116lbs Cast Steel Anvil

VEVOR9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 116 lb cast steel single horn anvil with a 50 HRC face, a rebound rate over 70% and a 22.5 by 3.9 inch working surface.

Pros

  • Working surface of 22.5 by 3.9 inches, the longest stated here
  • 50 HRC hardness from an 800 degree heat treatment
  • Rebound rate greater than 70% stated
  • Cutting table, pritchel hole and hardy hole stated

Cons

  • Spec table lists 110.0 pounds against 116 lbs in the title and bullets
  • No warranty term stated
  • No horn length is stated
  • No hole sizes stated
VEVOR Single Horn Anvil, 22Lbs Cast Steel Anvil

VEVOR Single Horn Anvil, 22Lbs Cast Steel Anvil

VEVOR9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 22 lb cast steel single horn anvil with a 50HRC face, a rebound rate over 70% and a 10.24 by 3.23 inch tabletop.

Pros

  • 50HRC hardness from an 800 degree heat treatment
  • Rebound rate over 70% stated
  • Round and square holes for bending, shaping, fitting and punching
  • Clamps or bolts to the workbench, with an unpainted surface

Cons

  • No warranty term stated
  • No cutting table stated, unlike the 116 lb VEVOR
  • No horn length is stated
  • Light enough to move on the bench unless clamped or bolted
Blacksmith Anvil 55 lbs (25 kg)

Blacksmith Anvil 55 lbs (25 kg)

Generic9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 55 lb gray cast iron anvil with a square horn, an 8.5 by 4 inch work surface and a precision hardy hole.

Pros

  • 8.5 by 4 inch work surface, the widest stated here
  • Square horn for bending and twisting metal
  • Precision hardy hole for auxiliary tools such as swages and fullers
  • Stable base that prevents wobbling during heavy hammering

Cons

  • Spec table lists 160.0 pounds against 55 lbs in the title and bullets
  • No warranty term stated
  • No hardness figure stated
  • No rebound rate stated
Olympia Tools 9-Pound Cast Iron Hobby Anvil 38-789

Olympia Tools 9-Pound Cast Iron Hobby Anvil 38-789

Olympia Tools9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 9 lb cast iron hobby anvil with a 5-1/2 by 2 inch face, a 3-1/2 inch horn and a Limited Lifetime warranty.

Pros

  • Limited Lifetime warranty stated, the only warranty term here
  • 9 lbs, the lowest weight stated here
  • 5-1/2 by 2 inch face with a 3-1/2 inch horn stated
  • Compact size for small tasks and hobby work

Cons

  • No hardness figure stated
  • No rebound rate stated
  • No holes stated
  • The listing contradicts itself on material: one bullet says cast steel, the title says cast iron

Spec sheet comparison

Anvil Gear Score Weight Material Hardness Work surface Warranty
Easmvetaln 132 lb 9.7/10 132 lbs Cast steel 55HRC 13.58 x 3.94 in Not stated
VEVOR 116 lb 9.6/10 116 lbs Cast steel 50 HRC 22.5 x 3.9 in Not stated
VEVOR 22 lb 9.6/10 22 lbs Cast steel 50HRC 10.24 x 3.23 in Not stated
Generic 55 lb 9.6/10 55 lbs Cast iron Not stated 8.5 x 4 in Not stated
Olympia 9 lb Hobby 9.4/10 9 lbs Cast iron Not stated 5-1/2 x 2 in Limited Lifetime

All specs here repeat what the maker rates and the listing prints, copied down 13 November 2026.

Buying guide: the best anvil for blacksmithing

Weight

Weight runs from 9 lbs on the Olympia hobby anvil to 132 lbs on the Easmvetaln, with the VEVOR anvils at 22 lbs and 116 lbs and the Generic at 55 lbs. A heavier anvil stays put under the hammer, while a lighter anvil moves around the shop and needs clamping or bolting to the bench. Check the weight on arrival: the 116 lb VEVOR lists 110.0 pounds in its spec table, and the 55 lb anvil lists 160.0 pounds there.

Cast steel or cast iron

The VEVOR anvils and the Easmvetaln are cast steel, while the Olympia and the Generic are cast iron. Hardness is stated only for the cast steel anvils: 50HRC on both VEVOR anvils and 55HRC on the Easmvetaln, all from an 800 degree heat treatment. Neither cast iron listing states a hardness figure, so compare the cast iron anvils on weight, face size and holes instead.

Work surface and holes

Work surfaces run from a 5-1/2 by 2 inch face on the Olympia to 22.5 by 3.9 inches on the 116 lb VEVOR. The Easmvetaln work surface is 13.58 by 3.94 inches, the Generic is 8.5 by 4 inches, and the 22 lb VEVOR tabletop is 10.24 by 3.23 inches. Holes matter for the work: the 116 lb VEVOR states a pritchel hole and a hardy hole plus a cutting table, the 22 lb VEVOR and the Easmvetaln state round and square holes, and the Generic states a hardy hole. The Olympia states no holes.

Rebound and hardness

Rebound is the face springing back after each strike, and the cast steel listings state a rebound rate over 70%. The VEVOR anvils state 50HRC and the Easmvetaln states 55HRC, all from an 800 degree heat treatment. The cast iron listings state no rebound rate and no hardness, so there is nothing to compare on those figures for the Olympia and the Generic.

Warranty

Only the Olympia states a warranty term, a Limited Lifetime warranty. The Generic warranty description reads 1, with no term stated, and the other listings state no warranty at all. A warranty term is worth weighing, but it does not replace the hardness and rebound figures.

Before You Strike an Arc

  • Bolt or clamp the anvil to the bench before striking: the VEVOR listings state the anvil can be clamped or bolted to the workbench to stay stable.
  • Check the weight on arrival: the 116 lb VEVOR lists 116 lbs in its title and 110.0 pounds in its spec table, and the 55 lb anvil lists 55 lbs against 160.0 pounds in its spec table.
  • Check the face and horn against the stated sizes: the Olympia face is 5-1/2 by 2 inches with a 3-1/2 inch horn, and the Easmvetaln work surface is 13.58 by 3.94 inches.
  • Run a forge outdoors or with strong ventilation, keep a fire extinguisher near, and never leave a forge lit.

FAQ for welders

What size anvil do I need for blacksmithing?

Match the weight to the work. The anvils here run from 9 lbs to 132 lbs: the 9 lb Olympia suits small tasks, the 22 lb VEVOR suits bench work that needs clamping, and the 116 lb VEVOR and 132 lb Easmvetaln suit full-size forging. Check the work surface too: faces run from 5-1/2 by 2 inches to 22.5 by 3.9 inches.

Do I need an anvil for blacksmithing?

An anvil is the work surface for riveting, flattening, forging and shaping, the tasks the listings name. A cast steel face with a stated rebound rate over 70% springs back after each strike, so the blow goes into the work. Without an anvil, there is no stated surface in these listings that does the same job.

Cast steel or cast iron: which anvil material is better?

The listings state hardness only for the cast steel anvils: 50HRC on both VEVOR anvils and 55HRC on the Easmvetaln, all from an 800 degree heat treatment. Neither cast iron listing states a hardness figure, so the choice rests on the stated figures: the cast steel anvils state hardness and rebound, the cast iron anvils do not.

What is the best anvil stand?

No stand is stated for any anvil here. The VEVOR listings state the anvil can be clamped or bolted to a workbench to stay stable, and the Easmvetaln and Generic listings describe a stable base. A workbench with clamps or bolts is the mounting the listings support.

Which anvil here has a warranty?

Only the Olympia, which states a Limited Lifetime warranty. The Generic warranty description reads 1, with no term stated, and the other listings state no warranty at all.

Related: best propane forge for blacksmithing, best blacksmith hammers, types of blacksmith hammers, and the blacksmithing hub. Also see the forges and anvils. Also see the propane vs charcoal forge. Also see the gas forge vs coal forge. Also see the best 2 burner forge. Also see our carbon vs stainless knife steel. Also see our 1084 vs 1095 knife steel. Also see our 1095 vs d2 knife steel. Also see our propane vs coal forge. Also see our best 12 ton hydraulic press.

More related guides (7)

Scoring, line by line

Each anvil is scored out of 10 on performance, build, value, safety listing and warranty. How we pick explains the weights. Anvils have no electrical safety listing to state, so no anvil here earns safety points; the ranking comes from the other criteria. Only the Olympia states a warranty term, a Limited Lifetime warranty.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Easmvetaln 132 lb 9.7 32 22 21 n/a 0
VEVOR 116 lb 9.6 30 21 21 n/a 0
VEVOR 22 lb 9.6 29 21 21 n/a 0
Generic 55 lb 9.6 28 20 20 n/a 0
Olympia 9 lb Hobby 9.4 23 16 15 n/a 3

A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Where safety does not apply (unpowered gear with no listed safety features), it is left out and the remaining 90 points make up the score.

More buying guides

Blacksmithing ·

Anvil Weight Guide for Blacksmithing

Anvil weight affects how steady the anvil sits under the hammer; this guide explains what 66 lb, 86 lb and 100 lb anvils suit…