Best Step Drill Bit Up to 32 Mm (2026): 5 Picks Compared
Five step drill bits for sheet metal and shop work, compared on size range, flute design, shank, coating and the materials each listing states.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallBOYOUYS M35 3-Pc Set9.7/10View on Amazon - 2
Most SizesTEWORDA 5-Pc Step Set9.6/10View on Amazon - 3
Reaches 32 mmsidnheywvn 4-32 mm Set9.6/10View on Amazon - 4
Standalone BitLenox 30882VB29.4/10View on Amazon - 5
For RAINPAL FittingsRAINPAL SDB1259.4/10View on Amazon
A hole that needs enlarging in sheet metal usually means swapping bits, finding the center again, and hoping the next size does not grab and spin the panel. A step bit cuts each size as it passes through the sheet, so a panel goes from pilot hole to finished size without a bit change. This guide covers the best step drill bit up to 32 mm for sheet metal and shop work, comparing five bits and sets on size range, flute design, shank, coating and the materials each listing states.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall BOYOUYS M35 3-Pc Set: M35 cobalt steel with a TiAlN coating, 34 sizes across 3 bits, and 4 spiral flutes. Check price on Amazon
- Most Sizes TEWORDA 5-Pc Step Set: 50 sizes across 5 step bits plus 5 countersink bits, with an aluminum case. Check price on Amazon
- Reaches 32 mm sidnheywvn 4-32 mm Set: A 3 piece set covering 4 to 32 mm in 15 steps per bit, on a 1/4 inch hex shank. Check price on Amazon
- Standalone Bit Lenox 30882VB2: A Lenox bit that drills 9 sizes from 1/2 inch to 1 inch, with a split point. Check price on Amazon
- For RAINPAL Fittings RAINPAL SDB125: Three steps at 21, 27 and 32 mm made for RAINPAL fittings, for use with a power drill. Check price on Amazon
The machines

M35 Four Spiral Flute Step Drill Bit Set
A 3 piece M35 cobalt set with 4 spiral flutes, a TiAlN coating and 34 sizes from 1/8 inch to 7/8 inch, on a 1/4 inch hex shank.
Pros
- M35 cobalt high speed steel with a TiAlN coating
- 34 hole sizes across 3 bits, from 1/8 inch to 7/8 inch
- 4 spiral flutes for smoother cutting and chip clearing
- Covers stainless steel, wood, aluminum and plastic
Cons
- Top size stops at 7/8 inch, short of 32 mm
- Boards must be thinner than the step height
- No warranty term is stated
- Three bits to keep track of

5 Pcs Step Drill Bit & 5 Pcs Countersink Drill Bit
A 5 step bit and 5 countersink set in titanium coated high speed steel, covering 50 sizes with an aluminum case and a center punch.
Pros
- 50 sizes across 5 step bits, up to 1-3/8 inches
- 5 countersink bits for 90 degree holes in wood and soft metal
- 118 degree split tip with a double groove design
- Aluminum case and a center punch in the box
Cons
- No warranty term is stated
- Countersinks suit wood and soft metal only
- Five step bits plus five countersinks take more bench space
- Titanium coating, not cobalt steel

3Pcs Large HSS Titanium Coated Step Drill Bit Set
A 3 piece titanium coated set covering 4 to 32 mm in 15 steps per bit, on a 1/4 inch hex shank with a storage bag.
Pros
- Covers 4 to 32 mm with 15 steps on each bit
- Two fluted design for faster, smoother drilling
- 1/4 inch hex shank works with impact ready power tools
- Black storage bag keeps the 3 bits together
Cons
- Iron plate up to 3 mm only
- Not for glass, tile or concrete walls
- Wood, PVC and insulation boards up to 5 mm only
- Titanium coating, not cobalt steel

Lenox Tools Step Drill Bit
A Lenox bit that drills 9 hole sizes from 1/2 inch to 1 inch, with a 2 flute design and a split point on a 3/8 inch shank.
Pros
- Split point design starts on contact with less walking
- 2 flute design cuts fast, clean, round holes
- Steam oxide treatment adds durability
- Drills 9 sizes from 1/2 inch to 1 inch
Cons
- Only 9 hole sizes from 1/2 inch to 1 inch
- Top size stops at 1 inch, short of 32 mm
- 2 flutes, fewer than the 4 flute sets here
- 3/8 inch shank rather than a hex shank

RAINPAL® SDB125 Step Drill Bit
A step bit made for RAINPAL fittings, with 3 steps at 7/8 inch, 1-1/16 inches and 1-1/4 inches, for use with a power drill.
Pros
- Reaches 32 mm on the 1-1/4 inch step
- Made to fit RAINPAL fittings, with the fitting models listed
- Power drill use gives more control
- Just the bit, nothing else to keep track of
Cons
- Made for RAINPAL products only
- Power drill only, not an impact driver
- Only 3 steps, so no in-between sizes
- Fits only the listed RAINPAL fitting models, so check yours before ordering
Spec sheet comparison
| Model | Gear Score | Size range | Steps | Shank | Coating | Materials | Warranty |
|---|---|---|---|---|---|---|---|
| BOYOUYS M35 3-Pc Set | 9.7/10 | 1/8 to 7/8 in | 34 sizes | 1/4 in hex | TiAlN | Stainless steel, wood, aluminum, plastic | None stated |
| TEWORDA 5-Pc Step Set | 9.6/10 | 1/8 to 1-3/8 in | 50 sizes | Not stated | Titanium | Metal, iron, aluminum, brass, plastic, wood | None stated |
| sidnheywvn 4-32 mm Set | 9.6/10 | 4 to 32 mm | 15 steps per bit | 1/4 in hex | Titanium | Plastic, aluminum, copper, wood, PVC | None stated |
| Lenox 30882VB2 | 9.4/10 | 1/2 to 1 in | 9 sizes | 3/8 in | Steam oxide | Not stated | None stated |
| RAINPAL SDB125 | 9.4/10 | 7/8 to 1-1/4 in | 3 steps | Not stated | Not stated | RAINPAL products | None stated |
All specs here repeat what the maker rates and the listing prints, copied down 21 November 2026.
Buying guide: the best step drill bit up to 32 mm for your shop
Size range
Range is the thing to check before anything else, since a step bit stops at its largest step. The BOYOUYS set runs from 1/8 inch to 7/8 inch across 3 bits, the TEWORDA set runs from 1/8 inch to 1-3/8 inches, and the Lenox bit runs from 1/2 inch to 1 inch. The sidnheywvn set lists a 4 to 32 mm range, and the RAINPAL bit reaches 32 mm on its largest step, so either suits holes at the top of this guide. Match the largest step to the hole you need before ordering.
Flutes and tip
Flutes clear chips and decide how smoothly a bit cuts. The BOYOUYS set states a 4 spiral flute design, the sidnheywvn set states a two fluted design, and the Lenox bit states a 2 flute design. For starting the hole, the TEWORDA set states a 118 degree split tip with a double groove design that centers itself and resists walking, and the Lenox bit states a split point design that starts on contact for fast penetration and less walking.
Shank
Two listings here state a 1/4 inch hex shank: the BOYOUYS set and the sidnheywvn set. The sidnheywvn listing says its 1/4 inch hex shank enables quick bit changes and works with impact ready power tools. The Lenox bit states a 3/8 inch shank. The TEWORDA and RAINPAL listings state no shank size, so check the fit against your own drill before ordering.
Coating and steel
The BOYOUYS set states M35 cobalt high speed steel with a TiAlN coating, which its listing describes as hard, with strong adhesion and a low friction coefficient. The TEWORDA and sidnheywvn sets state titanium coated high speed steel, and the Lenox bit states a steam oxide treatment that adds durability. The RAINPAL listing states no coating or steel grade, so there is nothing to compare on that point.
Materials
The BOYOUYS listing states stainless steel, wood, aluminum and plastic. The TEWORDA listing states metal, iron, aluminum, brass, plastic, aluminum alloy and wood. The sidnheywvn listing states plastic, aluminum, copper, wood, PVC sheet and insulation boards up to 5 mm, plus iron plate up to 3 mm. The RAINPAL bit is made for RAINPAL products only, so it suits one brand’s fittings and nothing else. Pick the bit whose stated materials match the stock on your bench.
Use as directed. Clamp the work before drilling, wear eye protection, and keep gloves away from a spinning bit. Step bits cut thin sheet fast, so hold the drill steady and let each step cut before moving on. Never exceed the stated thickness limits, such as iron plate up to 3 mm on the sidnheywvn set. See the OSHA machine guarding guidance.
Before You Strike an Arc
- Check the shank fits your drill chuck before drilling: the listings here state a 1/4 inch hex shank or a 3/8 inch shank where they state a shank size at all.
- Clamp thin sheet so it cannot spin up on the bit.
- Match the largest step to the hole you need: the sidnheywvn set lists 4 to 32 mm, and the RAINPAL bit lists 21, 27 and 32 mm steps.
- Use a power drill with the RAINPAL bit, not an impact driver, as its listing directs.
- Check the fitting model before ordering the RAINPAL bit, since it is made for RAINPAL products only.
FAQ for welders
How do you use a step drill bit?
A step bit drills each size as it passes through the sheet, so each bit covers many hole sizes without a bit change. Clamp the work, start on the smallest step, and stop at the step that matches the hole you need. Keep the board thinner than the step height, as the BOYOUYS listing directs, and let each step cut before moving to the next.
Do step drill bits work?
Yes, on the materials each listing states. The BOYOUYS listing states stainless steel, wood, aluminum and plastic, and the TEWORDA listing states metal, iron, aluminum, brass, plastic, aluminum alloy and wood. They suit thin sheet and plate within the stated thickness limits, and they drill each size as the bit passes through the sheet.
How do you use a step drill bit on metal?
Clamp the metal so it cannot spin, start the bit on its smallest step, and let each step cut before moving to the next. The TEWORDA listing states a 118 degree split tip that centers itself and resists walking, and the Lenox listing states a split point that starts on contact for fast penetration and less walking. Keep to the thickness limits the listing states for the metal at hand.
What is a step drill bit set?
A set of step bits that covers many hole sizes with a few bits instead of a drawer full of twist bits. The BOYOUYS set has 3 bits and 34 sizes, the TEWORDA set has 5 step bits and 5 countersink bits and 50 sizes, and the sidnheywvn set has 3 bits covering 4 to 32 mm. Each bit in a set covers a range of sizes, so the set replaces many fixed-size bits.
Can you sharpen step drill bits?
None of the listings here states a sharpening method or a resharpening service. The sidnheywvn listing says its bits can be reused over twice for clean hole drilling, which is the only reuse claim in this guide.
Related: best step drill bit for sheet metal, best step drill bit for stainless steel, best drill bit for stainless steel metal, best cobalt drill bit set, and the drilling and tapping hub. Also see our best step drill bit for aluminum. Also see our best cutting oil for drilling metal. Also see our drilling and tapping chart. Also see our best drill bit set for metal. Also see our sheet metal and tube hub.
Scoring, line by line
Each bit is scored on performance, build, value, safety listing and warranty, with the weights published on the How We Pick page. Step drill bits carry no electrical safety listing, so every bit here scores zero on that criterion, and the ranking comes from the other four. The top scorer is the BOYOUYS M35 set, with M35 cobalt steel and a TiAlN coating, while the sidnheywvn set is the one that lists a 4 to 32 mm range in millimetres.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| BOYOUYS M35 3-Pc Set | 9.7 | 32 | 22 | 21 | n/a | 0 |
| TEWORDA 5-Pc Step Set | 9.6 | 30 | 21 | 21 | n/a | 0 |
| sidnheywvn 4-32 mm Set | 9.6 | 29 | 20 | 20 | n/a | 0 |
| Lenox 30882VB2 | 9.4 | 26 | 20 | 16 | n/a | 0 |
| RAINPAL SDB125 | 9.4 | 24 | 19 | 18 | n/a | 0 |
A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Safety points apply to gear that runs on power or lists safety features. Without either, we score out of 90 instead of 100.




