Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Step Drill Bit for Aluminum (2026): 5 Compared

Five step drill bits compared by step range, coating, steel, shank and point, from a 5-piece metric set to a single 1-3/8 in M2 bit.

Best Step Drill Bit for Aluminum (2026): 5 Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1NEIKO 10198A 5-Pc SetBest OverallNEIKO 10198A 5-Pc Set9.5/10View on Amazon
  2. 2DEWALT DWA1790IR 3-PcBest Brand SetDEWALT DWA1790IR 3-Pc9.5/10View on Amazon
  3. 3EZARC M35 9-Step BitBest CobaltEZARC M35 9-Step Bit9.5/10View on Amazon
  4. 4Jerax M2 5-Size BitBest Big HoleJerax M2 5-Size Bit9.4/10View on Amazon

Aluminum panel on the bench, a hole that needs to go from pilot to final size without swapping bits half a dozen times. A step bit drills each diameter in one pass, and the right one for aluminum cuts clean without grabbing. This guide compares five step drill bits to find the best step drill bit for aluminum, ranked on step range, coating, shank and what each listing states.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall NEIKO 10198A 5-Pc Set: 5 bits covering 4 to 35 mm in titanium HSS with tri-flat shanks and a case. Check price on Amazon
  • Best Brand Set DEWALT DWA1790IR 3-Pc: 31 hole sizes in titanium nitride with hex shanks for impact drivers. Check price on Amazon
  • Best Cobalt EZARC M35 9-Step Bit: M35 cobalt with AlTiN at 89HRC, 9 steps on one bit. Check price on Amazon
  • Best Big Hole Jerax M2 5-Size Bit: Single M2 bit to 1-3/8 in with 5 marked sizes. Check price on Amazon

The machines

NEIKO 10198A Step Drill Bit Set | 5 Piece, 4mm

NEIKO 10198A Step Drill Bit Set | 5 Piece, 4mm

NEIKO9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-piece metric step drill bit set covering 4 to 35 mm in titanium-coated HSS, with 135-degree split points, 2 flutes and tri-flat shanks, in a case.

Pros

  • 5 bits covering 4 to 35 mm, 5 to 13 steps each
  • Titanium-coated HSS with 135-degree split point
  • Tri-flat shanks in 6, 8 and 10 mm
  • Case included, 518 g stated weight

Cons

  • Listing does not name aluminum directly
  • Metric only, no inch sizes
  • No warranty term is stated
  • 2 flutes, not a spiral flute
DEWALT Step Drill Bit Set:3 Piece

DEWALT Step Drill Bit Set:3 Piece

DEWALT9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3-piece titanium nitride step drill bit set with 31 hole sizes from 1/8 to 7/8 in, 1/4 in hex shanks optimized for impact drivers.

Pros

  • 31 hole sizes from 1/8 to 7/8 in
  • Titanium nitride coating, 2-flute spiral
  • 1/4 in hex shank, impact driver optimized
  • Laser-engraved step numbers

Cons

  • Listing names metal and steel, not aluminum
  • No warranty term is stated
  • 4.96 ounces for the set
EZARC M35 Cobalt Step Drill Bit for Metal

EZARC M35 Cobalt Step Drill Bit for Metal

EZARC9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A single M35 cobalt step drill bit, 1/4 to 3/4 in in 9 steps, with AlTiN coating rated at 89HRC, C-profile edge and triple spiral flute.

Pros

  • M35 cobalt steel with AlTiN coating at 89HRC
  • 9 steps from 1/4 to 3/4 in on one bit
  • C-profile edge with triple spiral flute
  • 1/4 in hex shank

Cons

  • Single bit only, narrower range than the sets
  • No warranty term is stated
  • Rated sheet limits: 1/8 in metal, 1 mm stainless
  • Cutting oil or coolant needed for continuous use
THINKWORK Four Spiral Flute Step Drill Bit

THINKWORK Four Spiral Flute Step Drill Bit

THINKWORK9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A single HSS step drill bit, 3/16 to 7/8 in in 12 steps, with 4 spiral flutes, laser-engraved sizes and a 1/4 in shank.

Pros

  • 12 steps from 3/16 to 7/8 in on one bit
  • 4 spiral flutes per the title and bullets
  • Laser-engraved step sizes
  • Lists aluminum among the materials

Cons

  • No warranty term is stated
  • No coating is stated
1/4"-1-3/8" M2 Step Drill Bit Unibit for Hole

1/4"-1-3/8" M2 Step Drill Bit Unibit for Hole

Jerax tools9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A single M2 high-speed steel step drill bit, 1/4 to 1-3/8 in in 5 marked sizes, with a 118-degree split point and polished steps.

Pros

  • Largest top size here: 1-3/8 in
  • 5 marked sizes on one bit
  • M2 high-speed steel, 118-degree split point
  • Lists aluminum, copper, wood and plastic

Cons

  • Single bit, only 5 sizes
  • Straight shank, no hex or tri-flat
  • Marketing percentages are maker claims
  • No warranty term is stated

Other welders and gear to compare

Spec sheet comparison

Model Gear Score Range Steps Steel / Coating Shank Warranty (stated)
NEIKO 10198A 5-Pc Set 9.5/10 4 to 35 mm 5 to 13 per bit Titanium HSS Tri-flat, 6 mm, 8 mm, 10 mm Not stated
DEWALT DWA1790IR 3-Pc 9.5/10 1/8 to 7/8 in 31 hole sizes Titanium nitride 1/4 in hex Not stated
EZARC M35 9-Step Bit 9.5/10 1/4 to 3/4 in 9 M35 cobalt, AlTiN 89HRC 1/4 in hex Not stated
THINKWORK 12-Step Bit 9.4/10 3/16 to 7/8 in 12 HSS 1/4 in Not stated
Jerax M2 5-Size Bit 9.4/10 1/4 to 1-3/8 in 5 M2 HSS Straight Not stated

These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 21 October 2026. Step counts and ranges are the listings’ stated figures. None of these listings states a warranty term.

Buying guide: best step drill bit for aluminum

Five bits made the short list: two multi-bit sets, two single high-spec bits and one 12-step bit. Step range first, then coating and steel, then the shank.

Step count and range

The NEIKO set covers 4 to 35 mm across 5 bits, with 5 to 13 steps per bit. The DEWALT set covers 1/8 to 7/8 in with 31 hole sizes across 3 bits. The EZARC covers 1/4 to 3/4 in with 9 steps on one bit. The THINKWORK covers 3/16 to 7/8 in with 12 steps on one bit. The Jerax covers 1/4 to 1-3/8 in with 5 marked sizes: 7/8, 1-1/8, 1-7/32, 1-1/4 and 1-3/8 in. Match the range to the largest hole on the job; a set covers more ground than a single bit.

Coating and steel

The NEIKO lists titanium-coated HSS with a 135-degree split point and 2 flutes. The DEWALT lists titanium nitride coating with a 135-degree split point and a 2-flute spiral. The EZARC lists M35 cobalt high-speed steel with an AlTiN coating rated at 89HRC, a C-profile edge and a triple spiral flute. The Jerax lists M2 high-speed steel with nitride surface hardening and a 118-degree split point. The THINKWORK lists HSS with 4 spiral flutes and laser-engraved step sizes. For aluminum, any of these steels cuts; the coatings matter more in stainless.

Shank: hex, tri-flat or straight

The DEWALT and EZARC list 1/4 in hex shanks, and the DEWALT is optimized for impact driver usage. The NEIKO lists tri-flat shanks in 6, 8 and 10 mm that fit impact drill chucks without slipping, per the listing. The Jerax lists a straight shank. The THINKWORK lists a 1/4 in shank. Hex shanks suit quick-change chucks and impact drivers; tri-flat shanks resist spinning in standard chucks.

What the listings leave unstated

No listing states a warranty term. The DEWALT spec table lists 1 piece and 3 packs against the 3-piece title and bullets; the title and bullets win. The THINKWORK spec table lists flute counts of both 2 and 4 against the four-flute title and bullets; the title and bullets win. The Jerax marketing percentages about tungsten and molybdenum are the maker’s claims. When a listing states nothing about a spec, the stated step range and coating are the whole comparison.

Before You Strike an Arc

  • Check the shank against the chuck: the DEWALT and EZARC list 1/4 in hex shanks, the NEIKO lists tri-flat shanks in 6, 8 and 10 mm.
  • The EZARC listing says to add cutting oil or coolant before continuous operation.
  • The Jerax listing rates its bit for stainless up to 12ga / 2.7mm; the EZARC lists metal sheet up to 1/8 in (3 mm) and stainless sheet up to 1 mm.
  • Match the step range to the hole: the NEIKO covers 4 to 35 mm across 5 bits, the DEWALT 1/8 to 7/8 in across 3 bits.

FAQ for welders

Can I use these step bits on aluminum?

The Jerax, EZARC and THINKWORK listings name aluminum directly. The DEWALT lists metal and steel, and the NEIKO lists steel and sheet metal. For thin aluminum panel, any of the five works; the aluminum-named listings are the direct match.

What size step bit do I need?

Match the range to the largest hole: 1/4 to 3/4 in on the EZARC, 3/16 to 7/8 in on the THINKWORK, 1/8 to 7/8 in on the DEWALT set, 4 to 35 mm on the NEIKO set, and 1/4 to 1-3/8 in on the Jerax.

Hex shank or straight shank?

The DEWALT and EZARC list 1/4 in hex shanks, and the DEWALT is optimized for impact driver usage. The NEIKO lists tri-flat shanks that resist slipping in impact drill chucks. The Jerax lists a straight shank and the THINKWORK a 1/4 in shank.

Do I need cutting oil with a step bit?

The EZARC listing says to add cutting oil or coolant before continuous operation. The other four listings do not state cutting-oil guidance.

How many steps does each bit have?

The NEIKO set has 5 bits with 5 to 13 steps each; the DEWALT set lists 31 hole sizes. The EZARC has 9 steps, the THINKWORK 12 steps and the Jerax 5 marked sizes on one bit each.

Scoring, line by line

Each bit is scored out of 10 on performance, build, value, safety and warranty, using only what the listing publishes. Performance carries the most weight, then build and value, with smaller shares for safety and warranty.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
NEIKO 10198A 5-Pc Set 9.5 32 22 21 0 0
DEWALT DWA1790IR 3-Pc 9.5 30 21 21 0 0
EZARC M35 9-Step Bit 9.5 30 21 20 0 0
THINKWORK 12-Step Bit 9.4 28 20 20 0 0
Jerax M2 5-Size Bit 9.4 27 19 19 0 0

Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score.

More welding guides

Related: titanium vs cobalt drill bits, step drill bit vs hole saw for sheet metal, best step drill bit for sheet metal, and the metal fab tools hub.

More buying guides