Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Magnetic Drill Low Profile (2026): 3 Compact Picks

Three low profile magnetic drills for tight steel work, compared on boring diameter and depth, magnetic force, motor power and the cutter each listing states.

Best Magnetic Drill Low Profile (2026): 3 Compact Picks
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1iMeshbean WF23824Best OveralliMeshbean WF238249.7/10View on Amazon
  2. 2Unibor E5000LPLargest Cutter CapacityUnibor E5000LP9.5/10View on Amazon
  3. 3VEVOR 8840ELowest Stated WeightVEVOR 8840E9.6/10View on Amazon

A steel bracket needs holes, and the beam it bolts to sits under a low shelf where a full size drill press cannot reach. A hand drill wanders on thick plate, and a tall mag drill will not fit the gap. That tight spot is where the best magnetic drill low profile earns its place: a short, compact mag drill that clamps to the steel and bores a clean hole where taller machines cannot fit. This roundup compares three low profile mag drills on what each listing states: boring diameter and depth, magnetic force, motor power and speed, and the cutter each one states.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall iMeshbean WF23824: The strongest stated magnetic force here, 2585 lbf, with the most stated power, 1380W, a 680 rpm top speed and a 3/4 inch annular cutter. Check price on Amazon
  • Largest Cutter Capacity Unibor E5000LP: A stated 2 inch cutter capacity with countersinking up to 1-3/16 inch, variable speed and an LED work light. Check price on Amazon
  • Lowest Stated Weight VEVOR 8840E: A stated 23.15 lb with overload protection, a cooling system and a 2248 lbf magnetic force. Check price on Amazon

The machines

1380W Low Profile Magnetic Drill Press with 3/4"

1380W Low Profile Magnetic Drill Press with 3/4"

iMeshbean9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1380W low profile mag drill with the strongest stated magnetic force here, 2585 lbf, a 680 rpm top speed, and a 3/4 inch annular cutter in the listing.

Pros

  • Strongest stated magnetic force here at 2585 lbf, from a double-coil base
  • 1380W pure copper motor with a stated top speed of 680 rpm
  • Bores 1.4 inch diameter holes to 1.8 inch deep, per the listing
  • 3/4 inch annular cutter stated in the listing

Cons

  • 28.0 lb, the heaviest stated weight here
  • No stated variable speed, only a top speed of 680 rpm
  • No stated overload protection
  • No stated countersinking capacity, unlike the Unibor
VEVOR Low Profile Magnetic Drill Press 1300W 1.4"

VEVOR Low Profile Magnetic Drill Press 1300W 1.4"

VEVOR9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1300W low profile mag drill with a stated 2248 lbf magnetic force, a 650 rpm no-load speed and a 3/4 inch Weldon shank, at the lowest stated weight here.

Pros

  • Stated 2248 lbf magnetic force, rated to hold on vertical or sloped surfaces
  • Overload protection and a cooling system stated in the listing
  • Bores 1.4 inch diameter holes to 1.8 inch deep
  • 23.15 lb, the lowest stated weight here

Cons

  • Lower stated magnetic force than the iMeshbean, 2248 lbf against 2585 lbf
  • Lower stated power and speed than the iMeshbean, 1300W and 650 rpm
  • No warranty term is stated
  • No stated countersinking capacity, unlike the Unibor
Unibor Low Profile Magnetic Drill Press

Unibor Low Profile Magnetic Drill Press

Unibor9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1200W low profile mag drill with the largest stated cutter capacity here, 2 inches, plus variable speed, an LED work light and countersinking up to 1-3/16 inch.

Pros

  • Largest stated cutter capacity here at 2 inches
  • Variable speed with a Smart Control panel, per the listing
  • Countersinking up to 1-3/16 inch stated
  • LED work light and LiftShield stated in the listing

Cons

  • 1200W, the lowest stated motor power here
  • No stated magnetic force, so its hold cannot be weighed against the 2248 lbf and 2585 lbf stated for the other drills
  • No warranty term is stated
  • Built around a 2 inch cutter capacity, so it suits larger holes rather than small bracket work

Spec sheet comparison

Model Gear Score Boring diameter Boring depth Magnetic force Motor power No-load speed Cutter
iMeshbean WF23824 9.7/10 1.4 in 1.8 in 2585 lbf 1380W 680 rpm 3/4 in annular cutter
VEVOR 8840E 9.6/10 1.4 in 1.8 in 2248 lbf 1300W 650 rpm 3/4 in Weldon shank
Unibor E5000LP 9.5/10 2 in Not stated Not stated 1200W Variable, rpm not stated 2 in capacity

These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 21 November 2026.

Buying guide: best magnetic drill low profile

Low profile drills trade height for reach. The three drills here all state a compact build for tight spaces, and the differences sit in boring size, magnet strength and motor power. Match those stated figures to the hole in front of you, and check the cutter shank before ordering.

Boring diameter and depth

Boring diameter sets the widest hole the drill can cut, and boring depth sets how deep it can go. The VEVOR and the iMeshbean both state a 1.4 inch boring diameter and a 1.8 inch boring depth, so they cover the same hole size on paper. The Unibor states a larger cutter capacity of 2 inches, with countersinking up to 1-3/16 inch, but states no boring depth. If the job needs a hole wider than 1.4 inches, the Unibor is the only pick here that states the capacity for it.

Magnetic force

Magnetic force holds the drill to the steel while the cutter turns. The iMeshbean states the strongest force here at 2585 lbf, and the VEVOR states 2248 lbf. The VEVOR listing says its base holds on vertical or sloped metal surfaces, which matters when the work cannot lie flat. The Unibor states no magnetic force, so its hold cannot be weighed against the other drills. The iMeshbean also states a double-coil base with a steel plate thickness of more than 10 mm, and a safety interlock that stops the motor from running when the magnetic base is not started.

Motor power and speed

Motor power and no-load speed show how hard the drill can push a cutter through steel. The iMeshbean states a 1380W pure copper motor with a top speed of 680 rpm. The VEVOR states 1300W with a 650 rpm no-load speed. The Unibor states 1200W with variable speed and no stated no-load speed. On stated power alone the iMeshbean leads and the Unibor trails, but the Unibor is the only pick here that states variable speed.

Low profile fit

Low profile means the drill fits where a standard mag drill cannot. The VEVOR and the iMeshbean both state dimensions of 11.0 x 3.9 x 8.3 inches, and both listings call the build compact and light for tight and hard-to-reach areas. The iMeshbean adds a detachable design that breaks the drill down for carrying and storage. The Unibor states no dimensions, so its height cannot be compared with the other drills. Check the stated size against the gap on the job before ordering.

Cutter and shank

The cutter does the work, and the shank has to match the drill. The VEVOR states a 3/4 inch Weldon shank. The iMeshbean states a 3/4 inch annular cutter, so the cutter size is stated up front. The Unibor states a 2 inch cutter capacity and countersinking up to 1-3/16 inch. The best annular cutter for magnetic drill roundup covers spares. Check the shank size on the cutter already in the shop before ordering a drill that takes a different shank.

Use as directed. Wear eye and face protection, clamp the work, keep gloves away from rotating parts, and keep guards in place. Set the magnetic base on clean, flat steel and switch the magnet on before the motor starts. Never exceed the stated cutter capacity, and keep the area clear of anything that can burn. See the OSHA machine guarding rules and the Safety Disclaimer.

Before You Strike an Arc

  • Set the base on clean, flat steel and switch the magnet on before starting the motor: the iMeshbean listing states the motor cannot run until the magnetic base is started.
  • Match the cutter to the shank: the VEVOR states a 3/4 inch Weldon shank, and the iMeshbean states a 3/4 inch annular cutter.
  • Check the cutter capacity against the hole: the Unibor states a 2 inch cutter capacity with countersinking up to 1-3/16 inch.
  • Wear eye and face protection, clamp the work, and keep gloves away from rotating parts.
  • On arrival, check the cutter, the shank fit and the magnet switch, and confirm the cooling system and overload protection stated for the VEVOR.

FAQ for welders

What is a low profile magnetic drill?

It is a compact mag drill that clamps to steel with a magnetic base and bores holes with an annular cutter, built short so it fits in tight spaces where a standard drill press or a tall mag drill cannot reach. The drills here state compact builds for tight and hard-to-reach areas, and two of them state dimensions of 11.0 x 3.9 x 8.3 inches. Use one when the work is steel plate, a beam or a frame that the magnet can grip.

What size holes can these drills bore?

The VEVOR and the iMeshbean both state a 1.4 inch boring diameter and a 1.8 inch boring depth. The Unibor states a 2 inch cutter capacity with countersinking up to 1-3/16 inch, but states no boring depth. Pick the drill whose stated diameter covers the hole.

How strong does the magnet need to be?

Strong enough to hold the drill still while the cutter bites. The iMeshbean states 2585 lbf and the VEVOR states 2248 lbf, and the VEVOR listing says its base holds on vertical or sloped metal surfaces. The Unibor states no magnetic force, so its hold cannot be compared with the other drills.

Can a low profile magnetic drill cut stainless steel?

The iMeshbean listing states it cuts steel, stainless steel, cast iron and various alloys, so stainless work is within its stated range. The VEVOR states its use for steelwork and industrial work, and the Unibor states core drilling, twist drilling and tapping without naming metals. Match the cutter to the metal before ordering.

Do these drills need a coolant system?

The VEVOR states a cooling system that keeps the temperature low during high-load work, so cooling is built into that pick. The iMeshbean and the Unibor state no cooling system. A cooling system suits long runs and deep holes, where heat builds up in the cutter.

Related: metalworking machines, best magnetic drill press, best magnetic drill for fabrication shop, magnetic drill vs benchtop drill press, best annular cutter set, drill press safety, best drill for tight spaces, best cutting fluid for steel, and the drill presses and grinders hub.

Scoring, line by line

Each drill is scored out of 10 on performance, build, value, safety features and warranty, with the weights published on the How We Pick page. Magnetic drills state safety features such as overload protection and a magnet interlock, so safety scores reflect what each listing states. No listing here states a warranty term, so every drill scores zero on warranty.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
iMeshbean WF23824 9.7 32 21 21 8 0
VEVOR 8840E 9.6 29 20 21 7 0
Unibor E5000LP 9.5 28 20 19 7 0

Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score.

More buying guides