Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Drill for Aluminum (2026): 5 Picks Compared

Five drill bits for aluminum compared by hole size range, cobalt content, coating, shank fit and the warranty each maker states.

Best Drill for Aluminum (2026): 5 Picks Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1toolant Large Step BitBest Overalltoolant Large Step Bit9.5/10View on Amazon
  2. 2SEDIANAS Step Bit SetWidest Size RangeSEDIANAS Step Bit Set9.5/10View on Amazon
  3. 3NEIKO 10625A Step BitBest Quick ChangeNEIKO 10625A Step Bit9.4/10View on Amazon
  4. 4Bosch CO2137BBest Single SizeBosch CO2137B9.4/10View on Amazon

Aluminum sheet on the bench, a bracket to mount or a panel to vent, and the hole has to land where you marked it and come out clean. That is the job the best drill for aluminum has to do, and the bits here split into step bits that cover many sizes in sheet and twist bits that drill one size deep and straight. This guide compares five on what each maker states: size range, material, coating, shank and warranty.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall toolant Large Step Bit: 15 steps from 1/4 to 2-1/2 in, M35 cobalt HSS with TiAlN coating and a 90 day warranty. Check price on Amazon
  • Widest Size Range SEDIANAS Step Bit Set: 5 step bits covering 50 sizes from 1/16 to 1-3/8 in, titanium coated 4241 HSS. Check price on Amazon
  • Best Quick Change NEIKO 10625A Step Bit: 9 steps from 1/2 to 1 in with a 1/4 in hex shank for quick change chucks. Check price on Amazon
  • Best Single Size Bosch CO2137B: A 5/32 in M42 cobalt bit with 8% cobalt and a three-flat shank. Check price on Amazon

The machines

toolant Large Diameter Step Drill Bit

toolant Large Diameter Step Drill Bit

AugTouf9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A large diameter step bit with 15 steps from 1/4 to 2-1/2 in, in M35 cobalt HSS with TiAlN coating and a 1/2 in shank.

Pros

  • 15 steps from 1/4 to 2-1/2 in cover large holes in one bit
  • M35 cobalt HSS with TiAlN coating, maker rated at 89HRC surface hardness
  • Four spiral flutes for chip removal on sheet work
  • 90 days warranty of free replacement or refund stated

Cons

  • 1/2 in shank needs a chuck that takes 1/2 in shanks
  • No sizes below 1/4 in, so small pilot holes need another bit
  • One bit only, so a damaged step ends the job
  • Large steps suit sheet, not thick plate
Step Drill Bit Set for Metal

Step Drill Bit Set for Metal

SEDIANAS9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5 piece titanium coated step bit set in 4241 HSS, covering 50 sizes from 1/16 to 1-3/8 in with two straight flutes.

Pros

  • 50 sizes from 1/16 to 1-3/8 in across 5 bits
  • 4241 HSS with titanium coating for heat and corrosion resistance
  • Two straight flutes for chip removal
  • Tri-flatted shanks grip in pistol drills

Cons

  • No warranty term is stated
  • Straight flutes, not spiral, on every bit in the set
  • Largest size stops at 1-3/8 in
  • Five bits to keep track of instead of one
NEIKO 10625A Step Drill Bit

NEIKO 10625A Step Drill Bit

NEIKO9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 9 step bit from 1/2 to 1 in in 4241 HSS with titanium nitride coating, spiral flutes and a 1/4 in hex quick change shank.

Pros

  • 9 steps from 1/2 to 1 in, sizes engraved on the bit
  • 135-degree split point tip to prevent walking
  • Two-flute spiral design pulls chips up and out
  • 1/4 in hex shank snaps into quick change chucks

Cons

  • No warranty term is stated
  • No sizes below 1/2 in on this bit
  • Largest size stops at 1 in
  • One bit only, with no spare in the box
BOSCH CO2137B 1-Piece 5/32 In. x 3-1/8 In. Cobalt

BOSCH CO2137B 1-Piece 5/32 In. x 3-1/8 In. Cobalt

Bosch9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A single 5/32 in jobber length twist bit in M42 cobalt with 8% cobalt alloy and a three-flat shank.

Pros

  • M42 cobalt with 8% cobalt alloy for heat resistance
  • Split point for easy starts with no skating
  • Three-flat shank grips in the chuck
  • Thick web-helix design for stability

Cons

  • One size only, 5/32 in, and one bit in the pack
  • Warranty covers product defects only, with no stated term
  • Jobber length limits drilling depth
  • No step sizes, so each hole size needs its own bit
3/32 Inch Cobalt Drill Bit (3 Pack) for Metal

3/32 Inch Cobalt Drill Bit (3 Pack) for Metal

Yellow Paw9.3/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3 pack of 3/32 in twist bits in M35 cobalt with TiAlN coating and a 135 degree split point.

Pros

  • 3 bits in the pack, so a spare is on hand
  • M35 cobalt with 5% cobalt steel and TiAlN coating
  • 135 degree split point to prevent walking
  • Maker states drilling into hardened steel up to 40 HRC

Cons

  • No warranty term is stated
  • One size only, 3/32 in, across all 3 bits
  • Flute length is 1-1/4 in, which limits depth
  • Rounded shank, not flatted, for chuck grip

Spec sheet comparison

Model Gear Score Type Sizes Material Shank Warranty
toolant Large Step Bit 9.5/10 Step bit 15 steps, 1/4 to 2-1/2 in M35 cobalt HSS, TiAlN 1/2 in 90 days
SEDIANAS Step Bit Set 9.5/10 Step bit set 50 sizes, 1/16 to 1-3/8 in 4241 HSS, titanium coating Tri-flatted Not stated
NEIKO 10625A Step Bit 9.4/10 Step bit 9 steps, 1/2 to 1 in 4241 HSS, titanium nitride 1/4 in hex quick change Not stated
Bosch CO2137B 9.4/10 Twist bit 5/32 in M42 cobalt, 8% cobalt Three-flat Product Defects Only
Yellow Paw 3/32 Cobalt 9.3/10 Twist bit, 3 pack 3/32 in M35 cobalt, TiAlN 3/32 in Not stated

Ratings in this table are the makers’ own claims taken from each product page (20 November 2026).

Buying guide: choosing the best drill for aluminum

Step bits or twist bits

Step bits drill many hole sizes with one bit and suit sheet, where each step widens the hole as it goes. The SEDIANAS set covers 50 sizes from 1/16 to 1-3/8 in across 5 bits, the NEIKO covers 9 steps from 1/2 to 1 in, and the toolant covers 15 steps from 1/4 to 2-1/2 in. Twist bits drill one size: the Bosch at 5/32 in and the Yellow Paw at 3/32 in. Pick step bits for varied holes in sheet, and twist bits when the same small hole repeats all day.

Hole size range

Match the range to the holes on your bench. For small holes under 1/2 in, the SEDIANAS set starts at 1/16 in and the two twist bits cover 3/32 and 5/32 in. For large holes in sheet, the toolant runs to 2-1/2 in, past the 1-3/8 in top of the SEDIANAS set and the 1 in top of the NEIKO. No pick here covers every size, so check both ends of the range before you buy.

Cobalt content and coating

Two picks state cobalt content: the Bosch in M42 cobalt with 8% cobalt alloy, and the Yellow Paw in M35 cobalt with 5% cobalt steel. The toolant is also M35 cobalt HSS. Coatings differ: TiAlN on the toolant and Yellow Paw, titanium coating on the SEDIANAS set, and titanium nitride on the NEIKO. The makers state these coatings for heat resistance and longer life; the Yellow Paw maker also states drilling into hardened steel up to 40 HRC.

Shank and chuck fit

Check the shank against your drill before anything else. The toolant needs a chuck that takes a 1/2 in shank. The NEIKO has a 1/4 in hex shank that snaps into a quick change chuck or impact driver. The SEDIANAS bits have tri-flatted shanks and the Bosch has a three-flat shank, both made to grip in the chuck. The Yellow Paw bits have a 3/32 in shank rounded to fit in any drill chuck, per the maker.

Use as directed. Clamp thin sheet so it cannot spin or climb the bit, keep hands clear of the cutting edges, and wear eye protection against chips. Let the bit cut at its own pace and clear chips from the flutes instead of forcing the drill. See our drill press safety notes for shop drilling basics.

Before You Strike an Arc

  • Check the shank fits your chuck: 1/2 in on the toolant, 1/4 in hex on the NEIKO, tri-flatted on the SEDIANAS set.
  • Read the size range on arrival: 50 sizes on the SEDIANAS set, 9 steps on the NEIKO, 15 steps on the toolant.
  • Clamp the sheet and mark the hole center; the Bosch and Yellow Paw split points are made to start without skating.
  • Count the bits in the box: 5 pieces in the SEDIANAS set, 3 bits in the Yellow Paw pack, one bit in the others.

FAQ for welders

Do step bits work on aluminum?

Yes. The SEDIANAS, NEIKO and toolant makers each state aluminum among their materials, and step bits suit sheet because each step widens the hole gradually. The NEIKO maker states its spiral design deburrs and expands holes for a cleaner process.

What is a split point?

A split point is a tip ground to start the hole where you place it, without skating across the surface. The Bosch maker states split points allow easy starts with no skating, and the Yellow Paw maker states its 135 degree split point lets you start and finish the hole in the same place.

Which shank fits my drill?

Match the shank to your chuck. The NEIKO 1/4 in hex shank snaps into a quick change chuck or impact driver. The toolant 1/2 in shank needs a chuck that takes 1/2 in shanks. The SEDIANAS tri-flatted shanks and the Bosch three-flat shank grip in regular chucks.

How many sizes does one step bit cover?

It depends on the bit. The NEIKO covers 9 steps from 1/2 to 1 in, the toolant covers 15 steps from 1/4 to 2-1/2 in, and the SEDIANAS set of 5 bits covers 50 sizes from 1/16 to 1-3/8 in.

Related: best step drill bits for aluminum, best drill bits for stainless steel, drilling tips for metal, and the sheet metal and tubing hub. Also see our best drills for metal. Also see our best step drill bits for sheet metal. Also see our HSS vs cobalt drill bits. Also see our best cutting oils for drilling metal. Also see our belt grinder mini.

Scoring, line by line

Each bit is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. Drill bits have no electrical safety listing to state, so every bit here scores zero on that criterion; the ranking comes from the other four.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
toolant Large Step Bit 9.5 30 21 20 0 2
SEDIANAS Step Bit Set 9.5 29 20 21 0 0
NEIKO 10625A Step Bit 9.4 27 20 20 0 0
Bosch CO2137B 9.4 26 22 18 0 0
Yellow Paw 3/32 Cobalt 9.3 23 19 20 0 0

The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure.

More buying guides