Radial Drill Press vs Standard Drill Press: Which One Should You Buy?
Radial and standard drill presses differ in how the head moves and work is positioned, and the right choice depends on work size, positioning needs and bench or floor space.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
JET 15-Inch Benchtop Drill PressView on Amazon - 2
JET 12" Benchtop Drill PressView on Amazon - 3
VEVOR 10 Inch Benchtop Drill Press 3.2 Amp Tabletop BenchView on Amazon - 4
QD-KYOHO 10-Inch Benchtop Drill Press- Variable Speed 50-3000View on Amazon - 5
13 in Floor Drill PressView on Amazon - 6
Klutch 13in. Benchtop Drill PressView on Amazon
A bracket clamped to the table will not reach the bit, and radial drill press vs standard drill press decides whether the head moves to the work or the work is positioned and clamped under a fixed head. No radial press is among the gear examples here, every example is a standard floor or benchtop press, so standard fits bench and floor shop work that fits stated swing, table and travel unless the job needs a moving head for large or awkward work.
Other welders and gear to compare
JET 15-Inch Benchtop Drill PressCheck price on Amazon
JET 12" Benchtop Drill PressCheck price on Amazon
VEVOR 10 Inch Benchtop Drill Press 3.2 Amp Tabletop BenchCheck price on Amazon
QD-KYOHO 10-Inch Benchtop Drill Press- Variable Speed 50-3000Check price on Amazon
13 in Floor Drill PressCheck price on Amazon
Klutch 13in. Benchtop Drill PressCheck price on Amazon
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
The difference in one paragraph
A standard drill press keeps the head fixed on a column and the work is positioned and clamped on the table under the bit. Swing, table size and quill travel set what fits and how deep the bit can go per stroke. A radial drill press puts the head on an arm that moves toward the work, so the work can stay clamped while the head shifts position. That helps on large work that is hard to shift, and takes more shop room than a standard press.
Side by side
| Powermatic floor press | JET 15-Inch benchtop press | JET 12 benchtop press | |
|---|---|---|---|
| Type | Floor drill press | Benchtop drill press | Benchtop drill press |
| Swing | 18″ | Not stated | 12″ |
| Quill travel | 6″ | 3-1/8″ | 3-1/8″ |
| Power | 1 HP | 3/4 HP | 1/2 HP |
| Speed | 250 to 3,000 RPM variable | 16 speed belt drive, RPM Not stated | 530 to 3,100 RPM variable |
| Table | 20-1/2″ x 14″ cast iron | 12-1/2″ x 17″ | 9-1/2″ x 9-1/2″ cast iron |
| Weight | 246 lb | 154.0 lb | 85 lb |
| Chuck | 5/8″ keyed | Not stated | 5/8″ keyed |
| Warranty | 5-year, 2 years commercial | 5-year, 2-year commercial | 5-year |
| Stated use | Woodworking, metal may void warranty | Not stated | Woodworking bench |
Figures in the table are maker stated for each standard example. Follow the manual and the chart on the machine for speed by bit and material, and see our drill press speed chart for how speed charts are read.
When a radial drill press is the better choice
- Large work that will not fit well on a table. The head moves to the work instead of forcing heavy or awkward stock under a fixed head.
- Work that must stay clamped. Fit-up stays put while the head shifts between hole locations, which helps when moving the work would lose position.
- Awkward shapes and reach. A moving head can reach points that a fixed head cannot reach without refixturing the work.
- Shop space for arm movement. Radial work needs room for the arm to swing and the work to stay clamped, plus solid setup for the machine size in use.
When a standard drill press is the better choice
- Bench and floor shop work. Standard examples here cover floor and benchtop setups, from the Powermatic floor press to JET benchtop presses for bench work.
- Stated swing and travel fit the work. Powermatic lists 18″ swing with 6″ quill travel, and JET JWDP-12 lists 12″ swing with 3-1/8″ travel for smaller bench jobs.
- Speed control is stated plainly. Powermatic lists 250 to 3,000 RPM without belt changes, JET JWDP-12 lists 530 to 3,100 RPM with digital readout, and JET JDP-15B lists 16 speed belt drive.
- Weight and mounting suit the shop. JET JWDP-12 lists 85 lb and must be bolted to a bench or stand, while Powermatic lists 246 lb and bolt to floor or base guidance.
Our best drill press guide compares standard presses for shop use, and our best drill press for metalworking guide covers metal shop picks.
How to tell which type a press is
Look at what moves. A standard press shows a fixed head on a column, a table that moves or cranks, and swing and travel stated for work under the head. A radial press shows an arm and a head that travel along that arm toward the work. Powermatic lists a table that cranks on the column, JET JWDP-12 lists a tilting table, and JET JDP-15B lists a table with T-slot grooves. Laser guides and safety keys do not make a press radial.
- Fixed head, clamped work. Standard layout, work is positioned and clamped on the table under the bit.
- Moving head on an arm. Radial layout, head is positioned over work that stays clamped.
- Swing stated for the head. Standard examples state swing for Powermatic and JET JWDP-12, swing is Not stated for JET JDP-15B.
Radial drill press vs standard drill press: which to choose
Choose standard when work fits the table, swing and travel stated for the press, and when bench or floor mounting suits the shop. Choose radial when work is too large or awkward to move under a fixed head and the head must come to the work. No radial example is compared here, so the gear below ranks standard examples only, in rank order by stated swing, travel, power, speed control and table size.
Powermatic floor press. Maker lists 18″ swing, 6″ quill travel, 1 HP and 250 to 3,000 RPM without belt changes, with a 20-1/2″ x 14″ cast iron table that tilts 0 to 90 degrees. Weight is listed as 246 lb, chuck as 5/8″ keyed, and warranty as 5-year with 2 years for commercial use. For metal work, maker states woodworking design and drilling metal may void warranty. Bits sold separately, bolting required.
JET 15-Inch benchtop press. Maker lists 3/4 HP, 16 speed belt drive, spindle travel of 3-1/8″ and a 12-1/2″ x 17″ work table with T-slot grooves. Weight is listed as 154.0 lb and warranty as 5-year with 2-year commercial terms stated in warranty text. Drawbacks: belt speed changes, RPM Not stated, chuck Not stated, swing Not stated.
JET 12 benchtop press. Maker lists 12″ swing, 3-1/8″ travel, 1/2 HP and 530 to 3,100 RPM with digital readout, plus a 9-1/2″ x 9-1/2″ cast iron table that tilts 45 degrees. Weight is listed as 85 lb, chuck as 5/8″ keyed, and warranty as 5-year. Drawbacks: smaller table and power, bench bolting required, bits and bolts not included. Maker states woodworking bench use.
For category browsing, see metalworking machines and drill press types for benchtop, floor and mini layouts.
Can one press cover both jobs?
No. A standard press cannot gain a moving radial head, and radial layout adds arm movement that bench work may not need. If work fits stated swing, table and travel, standard covers it. If work cannot move under a fixed head, radial is the answer.
Drill press safety. Clamp the work, keep guards in place, wear eye and face protection, and keep gloves away from rotating parts. Standard examples state safety keys on power switches, and Powermatic and JET JWDP-12 state laser guides and LED lights. Follow OSHA machine guarding guidance and the machine manual, and see our drill press safety guide for shop checks.
FAQ for welders
Is a radial drill press better than a standard drill press?
Radial is better when the head must move to large or awkward work that stays clamped. Standard is better for bench and floor work that fits stated swing, table and travel. No radial example is compared here, so this guide ranks standard examples only.
Can a standard drill press drill metal?
Check the maker statement for each press. Powermatic states the floor press is designed for woodworking and drilling metal or plastics may void the warranty. JET JWDP-12 states built for the woodworking bench, and metal use is Not stated for JET JDP-15B, so follow the manual for material limits.
What swing and travel do the standard examples state?
Powermatic lists 18″ swing and 6″ quill travel. JET JWDP-12 lists 12″ swing and 3-1/8″ travel. JET JDP-15B lists spindle travel of 3-1/8″, and swing is Not stated.
How is speed changed on these presses?
Powermatic lists variable speed from 250 to 3,000 RPM without belt changes by handwheel while running. JET JWDP-12 lists 530 to 3,100 RPM by lever while the motor runs with digital readout. JET JDP-15B lists 16 speed belt drive with belt tensioning, and RPM range is Not stated.
Do these presses state a warranty?
Powermatic lists 5-year warranty with 2 years for commercial use. JET JDP-15B warranty text lists 5-year with 2-year commercial terms. JET JWDP-12 lists 5-year warranty.
Related: benchtop vs floor standing drill press, drill press types, best drill press, and the drill presses and grinders hub. Also see our best drill for aluminum. Also see our belt grinder mini.




