Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Drill Bits for Copper: 5 Picks

Five drill bit sets for copper compared on material, point style, shank type and pack shape.

Best Drill Bits for Copper: 5 Picks
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1LingGan M35 Cobalt SetBest overallLingGan M35 Cobalt Set9.6/10View on Amazon
  2. 2Cortool Cobalt 20-PackBest bulk packCortool Cobalt 20-Pack9.6/10View on Amazon
  3. 3Highfire Titanium 12-PackBest for impact driversHighfire Titanium 12-Pack9.5/10View on Amazon
  4. 4Jerax Step Bit 2-3/8inBest for sheet copperJerax Step Bit 2-3/8in9.5/10View on Amazon
  5. 5COPOUIXR Cobalt SetBoxed setCOPOUIXR Cobalt Set9.5/10View on Amazon

Drilling copper sounds easy until the bit grabs, walks off the mark or work-hardens the hole halfway through. The best drill bits for copper are sharp, properly pointed bits in a material the listing names for copper: cobalt steel sets for repeated holes, titanium-coated bits for general shop use, or a step bit when the work is sheet copper with many hole sizes. These five picks, from 13-piece cobalt sets to a 14-size step bit, cover what the listings state for drilling copper.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best overall LingGan M35 Cobalt Set: M35 cobalt set in 13 metric sizes with 5 percent cobalt for hard and soft metals. Check price on Amazon
  • Best bulk pack Cortool Cobalt 20-Pack: Twenty 1/8 in M35 cobalt bits with 135-degree split points. Check price on Amazon
  • Best for impact drivers Highfire Titanium 12-Pack: Twelve 1/8 in titanium bits with 1/4 in hex quick-change shanks. Check price on Amazon
  • Best for sheet copper Jerax Step Bit 2-3/8in: One step bit with 14 marked sizes from 1/4 to 2-3/8 in. Check price on Amazon
  • Boxed set COPOUIXR Cobalt Set: 13-piece cobalt metric set with a labeled storage box. Check price on Amazon

The machines

Metric Cobalt Drill Bits Set 1.5-6.5mm 13PCS

Metric Cobalt Drill Bits Set 1.5-6.5mm 13PCS

LingGan9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

LingGan 13-piece M35 cobalt drill bit set, 1.5 to 6.5 mm, in high speed steel with 5 percent cobalt. The listing names stainless steel, iron, copper and aluminum, with a straight shank, 2 flutes and a gold finish.

Pros

  • M35 high speed steel with 5 percent cobalt
  • 13 sizes from 1.5 to 6.5 mm
  • Copper named among the listed materials
  • Straight shank for standard drill chucks

Cons

  • Straight point needs a center punch to start
  • Small sizes need attention to speed and temperature
  • No stated point angle like 135 degrees
  • No warranty term is stated
1/8 inch Cobalt Drill Bits (20Pcs)

1/8 inch Cobalt Drill Bits (20Pcs)

Cortool9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

Cortool 20-pack of 1/8 inch cobalt drill bits, 3.175 mm diameter with 42 mm flute length and 71 mm total length. They are M35 high speed steel with 5 percent cobalt, fully ground with 135-degree split points and straight shanks.

Pros

  • Twenty identical 1/8 inch bits for repeated holes
  • M35 steel with 5 percent cobalt
  • 135-degree split points, no center punch needed
  • Fully ground spiral flutes clear chips fast

Cons

  • Only one size: 1/8 inch
  • No case or storage stated
  • No warranty term is stated
  • Straight shank only, no hex option
1/8" 135 Degrees Split Point Drill Bits

1/8" 135 Degrees Split Point Drill Bits

Highfire9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

Highfire 12-pack of 1/8 inch titanium-coated twist drill bits with 1/4 inch hex quick-change shanks. They are 4341 high speed steel with 135-degree split points, and the listing names steel, copper, aluminum and zinc alloy.

Pros

  • 1/4 inch hex shanks fit impact drivers
  • 135-degree split points start without walking
  • Titanium coating claimed 3X the bit life
  • Copper named among the listed materials

Cons

  • Only one size: 1/8 inch
  • Titanium coating wears with resharpening
  • No warranty term is stated
  • Hex shank adds length in tight spots
2-3/8" HSS Step Drill Bit Unibit for Hole Drilling

2-3/8" HSS Step Drill Bit Unibit for Hole Drilling

Jerax tools9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

Jerax high speed steel step drill bit with 14 marked sizes from 1/4 inch to 2-3/8 inch. The self-starting tip needs no pilot hole, and the listing names sheet metal, copper, aluminum, wood and plastic.

Pros

  • 14 hole sizes in a single bit
  • Self-starting tip, no pilot hole needed
  • Polished steps with size markings
  • Copper named among the listed materials

Cons

  • For sheet stock, not deep holes
  • Single bit: no backup if it dulls
  • No stated point angle
  • No warranty term is stated
Cobalt Metric Drill bits Set 1.5-6.5mm/13PCS

Cobalt Metric Drill bits Set 1.5-6.5mm/13PCS

COPOUIXR9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

COPOUIXR 13-piece cobalt drill bit set, 1.5 to 6.5 mm, with 5 percent cobalt for hardness and heat resistance. It ships in a plastic storage box with size identification and states 135-degree spiral cutting edges.

Pros

  • 5 percent cobalt for hardness and heat resistance
  • 13 sizes from 1.5 to 6.5 mm
  • Labeled storage box included
  • Copper named among the listed materials

Cons

  • Not self-centering: maker recommends a center punch
  • Not for glass or ceramics, per the maker
  • Thinner listing than the LingGan set
  • No warranty term is stated

Other welders and gear to compare

Spec sheet comparison

Bit Gear Score Material Sizes Shank
LingGan M35 Cobalt Set 9.6/10 M35 HSS, 5% cobalt 1.5-6.5 mm, 13 pc Straight
Cortool Cobalt 20-Pack 9.6/10 M35 HSS, 5% cobalt 1/8″, 20 pc Straight
Highfire Titanium 12-Pack 9.5/10 4341 HSS, TiN coated 1/8″, 12 pc 1/4″ hex
Jerax Step Bit 2-3/8in 9.5/10 HSS 1/4″-2-3/8″, 14 steps Straight
COPOUIXR Cobalt Set 9.5/10 Cobalt HSS, 5% cobalt 1.5-6.5 mm, 13 pc Straight

Treat the specs as maker ratings pulled straight from the listings; we gathered them on 22 October 2026.

Buying guide: how to pick the best drill bits for copper

Copper shows up all over a fabrication shop: bus bars, grounding lugs, plumbing fittings, sheet for brackets and panels. Every listing here names copper among the materials its bits drill, so the choice comes down to bit material, point style, shank and whether you want a set, a bulk pack or a step bit. Here is how to read the listings.

Cobalt, HSS or titanium-coated

Three listings here are cobalt steel. The LingGan set and the Cortool 20-pack both state M35 high speed steel with 5 percent cobalt; the COPOUIXR set states 5 percent cobalt as well. The makers say the cobalt adds hardness, heat resistance and wear resistance over plain high speed steel. The Highfire 12-pack is 4341 high speed steel with a titanium nitride coating, which the maker claims extends bit life 3 times over uncoated bits. The Jerax step bit is plain high speed steel with a polished step finish. For copper specifically, any of these work, since every listing names copper; cobalt earns its keep when you drill copper day after day, because the bit stays sharp longer, while the titanium-coated set is the general-purpose shop choice.

Point angle and split points

Three listings state a 135-degree split point: the Highfire, the COPOUIXR and the Cortool. A split point starts without walking, which the Highfire listing describes as a no-walking drilling start, and the Cortool listing says no center punch is needed. The LingGan set states a straight point instead, and the COPOUIXR maker notes its bits are not self-centering and recommends a center punch on smooth curved surfaces. For copper, where a wandering bit mars the work, a split point is the detail to look for; with the LingGan set, plan on a center punch.

Shank: hex quick-change or straight

The Highfire set is the only one with 1/4 inch hex quick-change shanks, which fit impact drivers and stop the shank spinning in the chuck under pressure, per the listing. The other four are straight shank bits for a standard drill chuck. If your drilling happens with an impact driver, the hex shank set is the obvious pick; for a drill press or a regular drill, straight shank is the standard.

Set, bulk pack or step bit

The LingGan and COPOUIXR sets each cover 1.5 to 6.5 mm in 13 pieces, the full small-hole range for copper work like lugs and brackets. The Cortool and Highfire packs give you many identical 1/8 inch bits, 20 and 12 pieces respectively, which is the right shape when you drill the same hole over and over and wear bits out. The Jerax step bit is a different animal: one bit with 14 marked sizes from 1/4 inch to 2-3/8 inch for sheet metal, copper, aluminum, wood and plastic, with polished steps and size markings so you can see the target size while drilling. For sheet copper panels with varied hole sizes, the step bit replaces a whole index; for solid copper stock, the twist drill sets are the pick.

What the listings state about copper

Every listing here names copper outright. The LingGan set lists stainless steel, iron, copper and aluminum; the Highfire lists steel, copper, aluminum and zinc alloy; the Jerax lists sheet metal, copper, aluminum, wood and plastic; the COPOUIXR lists stainless steel, hard metal, cast iron, copper, aluminum and plastic; the Cortool lists hard metal, stainless steel, iron, copper, aluminium, brass, plastic and wood. Two notes from the fine print: the COPOUIXR maker says its bits do not apply to glass and ceramics, and the LingGan maker warns that small sizes need attention to speed and temperature. Both are worth heeding on copper, which rewards the right speed and steady feed.

Speed, pressure and heat: what the listings warn

Three listings carry usage warnings worth reading before the first hole. The LingGan maker says small sizes need attention to speed and temperature. The Cortool listing says to pay attention to speed, pressure and heat control during drilling. The COPOUIXR maker recommends a center punch on smooth curved surfaces for the best positioning, since its bits are not self-centering. Copper rewards the right speed and a steady hand: too fast and the bit overheats, too slow and it rubs instead of cutting. These warnings come from the makers, not from general shop lore, so they apply to the bits in front of you.

Before You Strike an Arc

  • Match the bit to the machine: hex shank for impact drivers, straight shank for drill presses and standard drills.
  • Check the point: three listings state 135-degree split points that start without walking; the others need a center punch.
  • Pick the pack shape: 13-piece sets for varied holes, bulk packs for repeated 1/8 inch holes, a step bit for sheet copper.
  • Mind the fine print: small bits need attention to speed and temperature, and cobalt bits are not for glass or ceramics.

FAQ for welders

What bit material is best for drilling copper?

Every listing here names copper. Cobalt steel sets like the LingGan, Cortool and COPOUIXR state M35 steel with 5 percent cobalt for hardness and heat resistance; the Highfire set is titanium-coated high speed steel; the Jerax step bit is plain high speed steel.

Do I need cobalt bits just for copper?

Not necessarily. The listings name copper for plain HSS and titanium-coated bits too. Cobalt pays off when you drill metal often and want the edge to last, per the makers’ wear resistance claims.

What point angle should the bits have?

Three listings state 135-degree split points, which the makers say start without walking and need no center punch. The LingGan set states a straight point, and the COPOUIXR maker recommends a center punch on smooth surfaces.

Hex shank or straight shank?

The Highfire set has 1/4 inch hex quick-change shanks for impact drivers; the listing says they stop shank spinning under pressure. The other four are straight shank for standard drill chucks and drill presses.

Step bit or twist drill bits for sheet copper?

The Jerax step bit drills 14 sizes from 1/4 to 2-3/8 inch in sheet copper with one tool. Twist drill sets suit solid stock and precise small holes from 1.5 mm up.

Related: titanium vs cobalt drill bits, black oxide vs cobalt drill bits, cobalt vs HSS drill bits for steel, and the metal fab tools hub. Also see our best drill bits for steel. Also see our best drill bits for cast iron. Also see our step drill bit vs hole saw for sheet metal.

Scoring, line by line

Each bit is scored on performance, build, value, safety and warranty, with the weights published on our How We Pick page. No listing here states a safety certification or a warranty term, so the ranking comes from the bit material, the point geometry and how completely the listing describes the set.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
LingGan M35 Cobalt Set 9.6 30 20 20 n/a 0
Cortool Cobalt 20-Pack 9.6 29 20 20 n/a 0
Highfire Titanium 12-Pack 9.5 28 19 20 n/a 0
Jerax Step Bit 2-3/8in 9.5 27 19 19 n/a 0
COPOUIXR Cobalt Set 9.5 26 19 19 n/a 0

Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.

More buying guides