Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Drill Bits for Cast Iron (2026)

Four drill bit sets for cast iron compared: M35 cobalt with 135 degree split points and double-end bits, ranked by listings.

Best Drill Bits for Cast Iron (2026)
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1GMTOOLS M35 1/8 Bit SetBest OverallGMTOOLS M35 1/8 Bit Set9.6/10View on Amazon
  2. 2Pro Edge M35 13pc SetBest RangePro Edge M35 13pc Set9.6/10View on Amazon
  3. 3DelitonGude 3/16 End BitDouble-End ValueDelitonGude 3/16 End Bit9.5/10View on Amazon

Cast iron drills differently than steel: it is hard but brittle, it throws chips instead of ribbons, and a dull bit walks. The best drill bits for cast iron are cobalt bits with a 135 degree split point that self-centers and a straight shank that resists walking. This guide compares four sets by material, tip, sizes, shank and warranty, all scored on what each listing states. All four are M35 sets with a 135 degree tip and a straight shank, and all four list cast iron as a surface.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall GMTOOLS M35 1/8 Bit Set: M35 cobalt 1/8 in bits with a 135 degree tip and a 30-day money back. Check price on Amazon
  • Best Range Pro Edge M35 13pc Set: 13 M35 sizes, 1/16 to 1/4 in, 135 degree split point and index box. Check price on Amazon
  • Double-End Value DelitonGude 3/16 End Bit: 3/16 in M35 bits with two cutting ends per bit for hard metal. Check price on Amazon

The machines

GMTOOLS 1/8 inch Cobalt Drill Bits, M35 HSS

GMTOOLS 1/8 inch Cobalt Drill Bits, M35 HSS

GMTOOLS9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

Ten 1/8 in M35 cobalt drill bits with a 135 degree tip twist design, straight shank, storage case and a 30-day money back guarantee.

Pros

  • M35 cobalt, 5% cobalt stated
  • 135 degree tip, self-centering
  • Sturdy plastic storage case
  • 30-day money back stated

Cons

  • Single size: 1/8 in only
  • Bullets mention 5/16 in oddly
  • Finish table says titanium, title M35
  • No cast iron only specialization
13pcs Cobalt Drill Bits Set M35 HSS Jobber Drill

13pcs Cobalt Drill Bits Set M35 HSS Jobber Drill

Pro Edge Technology9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

Thirteen M35 cobalt bits from 1/16 to 1/4 in with a 135 degree split point and an index storage box, rated for cast iron and hardened metal.

Pros

  • M35, 5% cobalt stated
  • 135 degree split point
  • 13 sizes, 1/16 to 1/4 in
  • Index storage box included

Cons

  • No warranty term stated
  • No double-end option
  • Cast iron is one of many surfaces
  • No sharpening stated
1/16-1/4inch HSS M35 Cobalt Twist Drill Bits

1/16-1/4inch HSS M35 Cobalt Twist Drill Bits

DelitonGude9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

Thirteen M35 cobalt bits from 1/16 to 1/4 in with a 135 degree tip and twist design, black oxide finish and full-grind nitriding for wear resistance.

Pros

  • M35, 5% cobalt stated
  • 135 degree tip, self-centering
  • 13 sizes, 1/16 to 1/4 in
  • Black oxide, nitrided grind

Cons

  • No warranty term stated
  • No storage box stated
  • 3 flutes is unusual for twist bits
  • No sharpening stated
3/16" inch Cobalt Double Ends Drill Bits Set,M35

3/16" inch Cobalt Double Ends Drill Bits Set,M35

DelitonGude9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

Ten 3/16 in M35 cobalt double-end bits with a 135 degree split point: two cutting ends per bit for steel, cast iron and other metals.

Pros

  • M35, 5% cobalt stated
  • Double-ended: 2 lives per bit
  • 135 degree split point
  • No center punch needed

Cons

  • Single size: 3/16 in only
  • Table lists 0.03 in cutting diameter
  • No warranty term stated
  • Uncoated finish

Other welders and gear to compare

Spec sheet comparison

Model Material Tip Sizes Shank Warranty
GMTOOLS M35 1/8 Bit Set M35 cobalt 135° 10x 1/8 in Straight 30-day money back
Pro Edge M35 13pc Set M35 cobalt 135° split 13 (1/16-1/4 in) Straight Not stated
DelitonGude M35 13pc M35 cobalt 135° 13 (1/16-1/4 in) Straight Not stated
DelitonGude 3/16 End Bit M35 cobalt 135° split 10x 3/16 in Straight Not stated

Ratings in this table are the makers’ own claims taken from each product page (21 October 2026). Where a listing states a figure two ways, the table shows both.

What the listings tell you

Two listings state figures two ways. The GMTOOLS title states 1/8 in bits against a 5/16 in mention in its bullets; trust the 1/8 in title. The DelitonGude 3/16 in double-end title states 3/16 in against a 0.03 in cutting diameter in its table; trust the title. Both DelitonGude listings state 3 flutes, against 2 on the others; a twist bit normally has 2, so treat the 3 as the listing states it.

Buying guide: the best drill bits for cast iron

Cobalt for cast iron

All four are M35 high-speed steel with 5% cobalt: both DelitonGude sets, the Pro Edge and the GMTOOLS. The listing claims for M35 are higher wear resistance and heat resistance, with the Pro Edge stating 3 to 5 times the life of M2 HSS. For cast iron, pick one of the M35 sets.

Tip angle and self-centering

All four M35 sets state a 135 degree tip: the DelitonGude 13pc a 135 tip and twist design, the Pro Edge a 135 degree split point, the GMTOOLS a 135 degree tip twist design, and the double-end DelitonGude a 135 degree split point. The split point self-centers and prevents walking, and the double-end listing states no center punch is needed.

Sizes and shanks

The DelitonGude 13pc and Pro Edge cover 1/16 to 1/4 in in 13 imperial sizes, with the Pro Edge adding an index storage box. The GMTOOLS ships ten 1/8 in bits, and the double-end DelitonGude ships ten 3/16 in bits with two cutting ends each: when one end dulls, the other end is a fresh bit. Shanks are straight on all four sets.

Drilling cast iron right

Cast iron wants firm feed, moderate speed and no hammer action. The double-end listing notes to pay attention to speed, pressure and heat control during drilling. Clear chips often: the listings state spiral grooves and flutes that clear particles and decrease friction and heat. The GMTOOLS listing notes its bits can be repeatedly sharpened without damaging the cutting edge.

Matching the set to the job

A range set suits general shop work: the DelitonGude 13pc and Pro Edge cover 1/16 to 1/4 in, so you pick the size the fastener needs. A single-size set suits production-style drilling: ten 1/8 in GMTOOLS bits or ten 3/16 in double-end DelitonGude bits mean you never stop to sharpen mid-job. Match the set to whether you drill many sizes or one size repeatedly.

Storage and organization

Bits are small and easy to lose. The Pro Edge ships a sturdy index storage box for easy storage and classification; the GMTOOLS ships a sturdy plastic case for storage and carrying. The DelitonGude 13pc and double-end sets state no case in their listings, so plan a bit index or pouch. The Pro Edge listing even notes to pull up the tab on the top of the case when opening to avoid damage.

Sharpening and replacement

Cobalt bits can be sharpened, and the GMTOOLS listing states its bits can be repeatedly sharpened without damaging the cutting edge. The double-end DelitonGude design skips sharpening entirely: when one cutting point is worn, the other end serves as a new bit. When chips stop curling and the bit squeals, it is time to sharpen or flip.

FAQ for welders

Do I need cobalt bits for cast iron?

The four M35 sets here all state 5% cobalt and list cast iron as a surface.

What tip angle is best?

All four M35 sets state 135 degrees, with split points that self-center.

Are double-end bits worth it?

The DelitonGude 3/16 in set gives two cutting ends per bit: when one end dulls, flip it and use the other end as a new bit.

Can I sharpen these?

The GMTOOLS listing states its cobalt bits can be repeatedly sharpened without damaging the cutting edge. No other listing here states sharpening.

Which of these states a warranty?

The GMTOOLS listing states a 30-day money back guarantee. No warranty term is stated on the other three listings.

Related: our metal fabrication tools hub, the best drill press for metal and our best drill press for metalworking and benchtop vs floor-standing drill press guides.

Scoring, line by line

Each set is scored on performance, build, value, safety and warranty, using only what the listing publishes. A spec the listing does not publish scores nothing.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
GMTOOLS M35 1/8 Bit Set 9.6 27 19 20 n/a 3
Pro Edge M35 13pc Set 9.6 28 20 21 n/a 0
DelitonGude M35 13pc 9.6 28 20 20 n/a 0
DelitonGude 3/16 End Bit 9.5 27 19 21 n/a 0

The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure. Where safety does not apply (unpowered gear with no listed safety features), it is left out and the remaining 90 points make up the score.

More buying guides