Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Hole Saw for Cast Iron (2026): 5 Picks for the Shop

Five carbide and bi-metal hole saws for cast iron, compared on cutting sizes, tooth design, pilot bits and depth of cut.

Best Hole Saw for Cast Iron (2026): 5 Picks for the Shop
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Vearter 17 Piece KitWidest Size RangeVearter 17 Piece Kit9.5/10View on Amazon
  2. 2EZARC 3 Piece KitSmall Kit PickEZARC 3 Piece Kit9.4/10View on Amazon
  3. 3Starrett DCH0338 86mmDeep Cut PickStarrett DCH0338 86mm9.4/10View on Amazon
  4. 4ASNOMY 4 Inch TCTLarge Single CutterASNOMY 4 Inch TCT9.4/10View on Amazon
  5. 5DECKRKAT 2-1/2 Inch TCTMid Size CutterDECKRKAT 2-1/2 Inch TCT9.3/10View on Amazon

Cast iron does not cut like mild steel. It is hard, abrasive and brittle, so a wood hole saw skates, dulls or snaps teeth, and the hole comes out ragged. This guide rounds up the best hole saw for cast iron options for shop and farm work, comparing what each listing states about tooth material, cutting sizes, pilot bits and depth of cut.

The picks run from single cutters for one diameter to a kit that covers a full range of small holes, and every pick here is listed for iron and hard metals. Carbide tipped cutters dominate the list, with one bi-metal deep cut saw for thicker stock.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Widest Size Range Vearter 17 Piece Kit: 15 cutters from 5/8 inch to 3 inch in one aluminum case. Check price on Amazon
  • Small Kit Pick EZARC 3 Piece Kit: 3 carbide cutters with 2 HSS pilot bits and a hex key. Check price on Amazon
  • Deep Cut Pick Starrett DCH0338 86mm: 86 mm bi-metal saw with a 51 mm deep cut depth. Check price on Amazon
  • Large Single Cutter ASNOMY 4 Inch TCT: 4 inch three-blade carbide cutter with 2 pilot bits. Check price on Amazon
  • Mid Size Cutter DECKRKAT 2-1/2 Inch TCT: 2-1/2 inch carbide cutter with a spring-loaded pilot bit. Check price on Amazon

The machines

17PCS 5/8''-3'' Carbide Hole Saw Kit for Metal

17PCS 5/8''-3'' Carbide Hole Saw Kit for Metal

Vearter9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 17 piece kit with 15 carbide tipped hole saws from 5/8 inch to 3 inch, a titanium-coated pilot bit and 2 hex spanners in an aluminum case.

Pros

  • 15 cutters covering 5/8 inch to 3 inch in one case
  • Carbide tipped cutters with a titanium-coated pilot bit
  • Aluminum case keeps the set together in the shop
  • Listed for stainless steel, iron, mild steel, alloy steel and aluminum

Cons

  • No cutting depth stated for the cutters
  • No warranty term in the listing
  • A large kit to store if only one size is needed
EZARC Carbide Hole Saw Kit

EZARC Carbide Hole Saw Kit

EZARC9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3 piece carbide tipped kit in 7/8 inch, 1-1/8 inch and 1-3/8 inch, with 2 HSS pilot drill bits and a hex key.

Pros

  • Carbide teeth, with a maker claim of more than 10 times longer life than bi-metal on hardened metal
  • 3 common sizes for small holes in plate
  • Includes 2 HSS pilot drill bits and a hex key
  • Cuts material smaller than 5 mm per the listing

Cons

  • Only 3 cutter sizes, no larger diameters
  • No warranty term in the listing
  • Item thickness stated as 5 millimeters only
Starrett Deep Cut Hole Saw

Starrett Deep Cut Hole Saw

Starrett9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A heavy duty bi-metal deep cut hole saw in 86 mm with extra cobalt HSS teeth, rated for metal over 3 mm thick.

Pros

  • Deep cut depth of 51 mm, 2 inch
  • Extra cobalt HSS teeth for metals, wood, cast iron, fibreglass and plastic
  • Smooth cutting with light vibration per the listing
  • High-quality HSS steel with enhanced heat resistance, per the listing

Cons

  • Arbor and pilot drill not included, and an extended length pilot drill is required
  • Single cutter, one diameter only
  • No warranty term in the listing
4'' Tungsten Carbide Tipped Hole Saw Drill Bit

4'' Tungsten Carbide Tipped Hole Saw Drill Bit

ASNOMY9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A single 4 inch tungsten carbide tipped cutter with a three-blade tooth design and 2 titanium-plated pilot drill bits.

Pros

  • Three-blade design: outer, middle and inner blades
  • 4 inch cutting diameter for large holes
  • Includes 2 titanium-plated pilot drill bits
  • Each cutter cased in a plastic box and oiled against rust

Cons

  • Single diameter only
  • Cutting depth of 1 inch limits thicker stock
  • Cannot be used for concrete, tiles and stone per the listing
  • No warranty term in the listing
2-1/2" TCT Hole Saw for Hard Metal

2-1/2" TCT Hole Saw for Hard Metal

DECKRKAT9.3/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 2-1/2 inch tungsten carbide tipped cutter with a spring-loaded pilot drill bit and a 3/8 inch 3-flatted shank.

Pros

  • Spring-loaded pilot bit for debris removal
  • 3/8 inch 3-flatted shank for grip against slippage
  • Pre-oiled cutter in a sturdy plastic case
  • Maker tips: start low torque and speed, use cutting oil

Cons

  • Set name says 4 piece while bullets name a saw, a pilot bit and a hex wrench
  • Single diameter only
  • Cutting length of 1 inch
  • No warranty term in the listing

Other welders and gear to compare

Spec sheet comparison

Pick Gear Score Cutting sizes Teeth Pilot bit Warranty
Vearter 17 Piece Kit 9.5/10 5/8 in to 3 in, 15 cutters Carbide tipped Titanium-coated None stated
EZARC 3 Piece Kit 9.4/10 7/8 in, 1-1/8 in, 1-3/8 in 6, carbide tipped 2 HSS pilot bits None stated
Starrett DCH0338 86mm 9.4/10 86 mm, single diameter Extra cobalt HSS Not included None stated
ASNOMY 4 Inch TCT 9.4/10 4 in, single diameter 3, three-blade carbide 2 titanium-plated None stated
DECKRKAT 2-1/2 Inch TCT 9.3/10 2-1/2 in, single diameter Tungsten carbide tipped Spring-loaded None stated

These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 29 October 2026.

Buying guide: choosing the best hole saw for cast iron

Tooth material

Carbide tipped teeth suit hard and abrasive metals. Four picks here use tungsten carbide tipped cutters, and the EZARC listing claims more than 10 times longer life than a bi-metal hole saw on hardened metal drilling. The Starrett takes the other route: a bi-metal saw with extra cobalt HSS teeth, built for metals, wood, cast iron, fibreglass and plastic. For cast iron specifically, either tooth family appears in these listings, so pick by the diameter and depth you need rather than by tooth material alone.

Size range

Single cutters cover one diameter: 4 inch on the ASNOMY, 86 mm on the Starrett, and 2-1/2 inch on the DECKRKAT. Kits cover a range: the EZARC kit gives 7/8 inch, 1-1/8 inch and 1-3/8 inch, while the Vearter kit runs from 5/8 inch to 3 inch across 15 cutters. Match the cutter to the fitting or pipe that has to pass through the hole, and remember that the Starrett 86 mm size is one saw, not the whole Deep Cut line.

Depth of cut

Depth decides whether a cutter gets through the stock in one pass. The Starrett deep cut saw states a 51 mm, 2 inch depth and suits metal of more than 3 mm thickness. The ASNOMY states a 1 inch cutting depth and the DECKRKAT a 1 inch cutting length. The EZARC and Vearter listings state no cutting depth, so check the listing before counting on them for thick castings.

Pilot bits and arbors

The pilot bit centers the saw and clears the first chips. The ASNOMY ships 2 titanium-plated pilot drill bits, the EZARC ships 2 HSS pilot drill bits with a hex key, the Vearter uses a titanium-coated pilot bit, and the DECKRKAT uses a spring-loaded pilot bit with a hex wrench. The Starrett is the exception: it does not include the arbor and pilot drill, and it requires arbors with an extended length pilot drill. If the arbor is not already in the shop, that pick costs extra parts.

Cutting oil and speed

The DECKRKAT listing gives the clearest cutting advice here: begin with low torque and speed on the pilot bit alone, increase speed as the saw meets the surface, and use cutting oil to prevent burning or breaking the bit. That advice fits cast iron work generally, where heat dulls teeth fast. Keep the work clamped, keep the drill steady, and clear chips instead of forcing the saw.

Use as directed. Clamp the work before cutting, keep hands clear of the rotating saw, and wear eye protection against chips. Cast iron throws abrasive dust and sharp chips, so clear the cut often and let the saw cool between holes. Never exceed the stated cutting depth or force a dull cutter through the work.

Before You Strike an Arc

  • Match the cutter to the drill on hand: the listings name bench drills, magnetic drills, gun drills, hand held electric drills and stand and bracket motor-driven drilling machines.
  • Check the pilot bit and arbor on arrival, since the Starrett ships without either and the kits ship their own bits.
  • Keep cutting oil at the bench: the DECKRKAT listing calls for it to prevent burning or breaking the bit.
  • Confirm the diameter against the fitting before cutting, since most picks here are single diameters or fixed kit sizes.
  • Check the case and oiling on arrival: the ASNOMY and DECKRKAT cutters ship oiled in plastic cases, and the Vearter kit ships in an aluminum case.

FAQ for welders

Can a hole saw cut cast iron?

Yes, when the listing states it. Every pick here is listed for iron or hard metals, with carbide tipped teeth on four picks and extra cobalt HSS teeth on the Starrett. Pick a cutter whose listing names cast iron or hard metal, and respect its stated cutting depth.

What tooth material suits cast iron?

Carbide tipped teeth suit hard and abrasive metals, and four picks here use them. The Starrett uses bi-metal teeth with extra cobalt HSS, which the listing rates for metals, wood, cast iron, fibreglass and plastic. Either family works on paper here; diameter and depth matter more than the tooth label.

Do I need cutting oil when cutting cast iron?

The DECKRKAT listing says to use cutting oil as a lubricant to prevent burning or breaking the bit, and to start with low torque and speed on the pilot bit alone. Heat dulls teeth fast in cast iron, so oil and a steady feed help the cutter last. Follow the listing advice for the cutter in hand.

Why does the Starrett need a special arbor?

The Starrett Deep Cut saw requires arbors with an extended length pilot drill, and it does not include the arbor and pilot drill. The deep cut depth of 51 mm needs the longer pilot to reach through the work. Check the arbor before ordering, since it is a separate part.

What size hole saw do I need for a fitting?

Match the cutter diameter to the fitting that must pass through the hole. The Vearter kit covers 5/8 inch to 3 inch, the EZARC kit covers 7/8 inch to 1-3/8 inch, and the single cutters cover 2-1/2 inch, 86 mm and 4 inch. Measure the fitting first, then pick the kit or single cutter that holds that size.

Related: annular cutter vs hole saw, best angle grinder for cutting metal, and benchtop vs floor standing drill press.

Scoring, line by line

Each cutter is scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. Hole saws state no electrical safety listing, so every pick scores zero on that criterion; the ranking comes from the other four. No listing here states a warranty term, so every pick also scores zero on warranty.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
Vearter 17 Piece Kit 9.5 29 21 21 0 0
EZARC 3 Piece Kit 9.4 28 20 20 0 0
Starrett DCH0338 86mm 9.4 28 21 18 0 0
ASNOMY 4 Inch TCT 9.4 27 20 19 0 0
DECKRKAT 2-1/2 Inch TCT 9.3 26 19 19 0 0

Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score.

More buying guides

Metal Fab Tools ·

Best Drill Bits for Cast Iron (2026)

Four drill bit sets for cast iron compared: M35 cobalt with 135 degree split points and double-end bits, ranked by listings.