Mill Tool Holder Types: A Guide to Each Style
A mill holds the cutter in a holder, and the holder decides how true the cut runs, so this guide walks through ER collet chucks, R8 and CAT40 shanks, and collet blocks for workholding.

On this page
A cutter that chatters, a hole that drifts off layout, a finish that looks torn instead of cut. When the tool moves in the holder, the mill cannot cut true, no matter how sharp the cutter is. This guide explains mill tool holder types, from ER collet chucks to taper shanks and square and hex collet blocks, so the holder on the spindle matches the work on the table.
As an Amazon Associate I earn from qualifying purchases. This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Mill Tool Holder Types at a Glance
A tool holder does two jobs: it grips the cutter shank, and it seats in the spindle taper. The grip decides whether the cutter stays put under load, and the taper decides whether the holder runs true. ER collet chucks grip with a slotted collet squeezed by a nut, R8 and CAT40 holders seat by taper and drawbar, and collet blocks hold work instead of cutters, clamped in a vise or on the table.
| ER11 | ER16 | ER32 | ER40 | |
|---|---|---|---|---|
| Collet range in the listings | 1 mm to 7 mm, plus 1/4 and 1/8 inch | 1/16 to 13/32 inch | 3/32 to 3/4 inch | Not stated |
| Accuracy figure in the listings | 0.02 mm | 0.0008 inch TIR | 0.0004 inch | 0.005 mm |
| Shank or mount in the listings | M14 threaded nut | CAT40 | R8 shank, 7/16-20 thread | Collet block, square and hex |
| Pieces in the set | 19 | 12 | 12 collets, plus R8 shank and wrench | 2 blocks |
| Material stated | 65 Mn spring steel | 45# alloy steel | Carbon steel | Carbon steel |
Read the table for what each size covers, then match the holder to the spindle taper on the mill. A holder that does not match the taper cannot run true, whatever the collet inside it.
ER Collet Chucks
ER collets are the common grip for small mills, drill presses and CNC spindles. A collet is a slotted sleeve that closes around the cutter shank as the nut tightens, and each collet covers a narrow range of shank sizes, so a set covers the spread with one collet per size. The Yaocom ER11 (on Amazon) set holds 19 pieces: 15 collets from 1 mm to 7 mm plus 1/4 inch and 1/8 inch sizes, with 4 clamping nuts on M14 thread. The collets are 65 Mn spring steel, and the maker states accuracy of 0.02 mm.
ER16 steps up the range. The VEVOR ER16 (on Amazon) set holds 12 collets from 1/16 inch to 13/32 inch, with 0.0008 inch TIR, in 45# alloy steel, and it comes with a storage case. Accusize lists a 10 piece ER16 set from 1/32 inch to 3/8 inch, hardened to 44 to 48 HRC, with concentricity of 0.0004 inch and a runout check on each piece.
ER32 is the size the R8 sets here use. The INPANOLS R8 ER32 (on Amazon) set holds 12 collets from 3/32 inch to 3/4 inch, with an R8 shank on 7/16-20 thread and a wrench, and accuracy to 0.0004 inch. Accusize lists the same spread in a 12 piece set plus an R8 Bridgeport shank holder and a wrench in a fitted box, 13 pieces in all, with the collet nut made eccentric and ISO 15488:2003(E) compliance stated. The SHZOND CAT40 package (on Amazon) pairs ER32 and ER16 collets on CAT40 tooling, with 12 ER32 collets and 10 ER16 collets, a 0.0001 inch accuracy figure, and through spindle coolant from the pull stud to the collets. ER40 turns up in the listings only as collet blocks, covered below, not as a collet set.
R8 and CAT40 Shanks
The shank is the part that seats in the spindle, and it must match the taper the mill was built for. R8 is the taper on Bridgeport style mills, and the R8 ER32 sets above seat an ER32 collet chuck on an R8 shank with 7/16-20 thread. The fitting notes say to tilt the collet onto the nut of the holder sleeve, then tighten the nut, and the collet sits in the center of the holder when it is fitted right.
CAT40 is the taper on larger machining centers, and the SHZOND package is built for it: CAT40 ER32 and ER16 collet sets, high speed true balance in 15 to 20K RPM, hardened and ground chucks, and through spindle coolant from the pull stud to the collets. The ER16 chuck in that package has a gage length of 2.75 inches. A CAT40 holder does not fit an R8 spindle, and an R8 holder does not fit a CAT40 spindle, so check the taper on the mill before ordering a holder. For the cutters that go in these holders, see the end mill types guide.
Collet Blocks for Workholding
A collet block holds the work, not the cutter. It is a square or hex block with a collet seat inside, and it clamps in a vise or sits on the table so a round part can be milled, drilled or ground on flat faces. The Jecoupoon ER32 set pairs a hex block of about 47 by 69 mm with a square block of about 45 by 69 mm, ground to 0.2 to 0.3 mm flatness, in carbon steel, with one piece molding for concentricity. The Lzcdelyxiao ER32 set holds one square block and one hex block, with 0.005 mm accuracy stated.
ER40 blocks run larger. The Lzcdelyxiao ER40 (on Amazon) set holds one square block and one hex block in carbon steel, with the error held within 0.005 mm, and the Pastlla ER40 set holds the same pair in hardened carbon steel. The ER32 blocks and the Lzcdelyxiao ER40 set suit cross hole drilling at 60, 90 or 120 degrees, and the blocks suit parallel, square or hex shapes. Set the block on a flat face, clamp it firm, and check the angle before cutting.
How to Pick the Right Holder
Start with the spindle taper. An R8 holder fits an R8 spindle, a CAT40 holder fits a CAT40 spindle, and a collet chuck is only as true as the taper it seats in. Then match the collet to the cutter shank: the shank must fall inside the collet range, and a collet forced onto a shank outside its range grips poorly and runs out.
Check the accuracy figure the maker states, and compare like with like. The listings here state 0.0004 inch on the ER32 sets, 0.0008 inch TIR on the VEVOR ER16 set, 0.0001 inch on the SHZOND CAT40 package, and 0.02 mm on the Yaocom ER11 set. A smaller figure means a truer holder, but only when the figures measure the same thing, so read whether the maker states TIR, runout or accuracy before comparing.
Check what comes in the box before ordering. The sets here range from a pair of blocks to a 19 piece set with nuts, and the R8 sets include the shank and a wrench. A set without the wrench or the nut it needs is not ready to run. On arrival, check the threads, seat a collet and confirm it sits centered, and keep the collets in the case so they stay clean. For the shank sizes that go in these collets, see the end mill sizes guide.
FAQ for welders
What is an ER collet chuck?
It is a holder that grips a cutter shank with a slotted collet squeezed by a nut. Each collet covers a narrow range of shank sizes, so a set holds one collet per size. ER11, ER16, ER32 and ER40 are the sizes in the listings here, with ER32 the size the R8 sets use.
Can I use an R8 holder in a CAT40 spindle?
No. R8 and CAT40 are different tapers, and a holder only seats true in the taper it was made for. Check the taper on the mill first, then order the holder that matches it. The R8 sets here seat ER32 collets on an R8 shank, and the CAT40 package seats ER32 and ER16 collets on CAT40 tooling.
What is a collet block used for?
It holds round work so it can be milled, drilled or ground on flat faces. The block is square or hex, with a collet seat inside, and it clamps in a vise or sits on the table. The ER32 blocks and the Lzcdelyxiao ER40 set suit cross hole drilling at 60, 90 or 120 degrees, and the blocks suit parallel, square or hex shapes.
How accurate are ER collets?
It depends on the set. The listings here state 0.0004 inch on the ER32 sets, 0.0008 inch TIR on the VEVOR ER16 set, 0.0001 inch on the SHZOND CAT40 package, and 0.02 mm on the Yaocom ER11 set. Compare figures that measure the same thing, and check that the collet seats centered on arrival.
Related: end mill types, end mill sizes, drill press vs mini mill, best drill bit set for metal, and the metal fab tools hub.




