Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

End Mill Types Explained for Metalworking

End mill types differ by nose shape, flute count, shank and coating, and the right type follows the cut: flat bottoms, round pockets, or fine finish work.

End Mill Types Explained for Metalworking
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Genmitsu 40pcs End Mills CNC Router BitsGenmitsu 40pcs End Mills CNC Router Bits9.6/10View on Amazon
  2. 2Shars 3/16" -3/4" HSS Single End Mill SetShars 3/16" -3/4" HSS Single End Mill Set9.6/10View on Amazon
  3. 3SpeTool 5PCS 2 Flutes Square Nose End Mill SetSpeTool 5PCS 2 Flutes Square Nose End Mill Set9.6/10View on Amazon
  4. 4Home of quality tools 6pcs 1/2 inch 3/8 inch 5/16Home of quality tools 6pcs 1/2 inch 3/8 inch 5/169.6/10View on Amazon

A slot that needs a flat bottom, a pocket with round corners and a profile cut in aluminum all ask for different cutters, and end mill types are the first choice to get right before the spindle starts. An end mill is a rotary cutter that mills sideways as well as down, and the shape of its nose and the number of its flutes decide what it can cut and how clean the edge comes out. This guide explains the main types, when each one fits, and the sets that cover them.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Genmitsu 40pcs End Mills CNC Router Bits

Genmitsu 40pcs End Mills CNC Router Bits

Genmitsu9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 40-piece set of 2-flute flat nose and ball nose end mills on a 1/8 inch shank, with Nano Blue and Titanium coatings and cutting diameters from 0.8 to 3.175 mm.

Pros

  • 40 pieces across cutting diameters from 0.8 to 3.175 mm
  • Flat nose and ball nose cutters in the same set
  • Nano Blue and Titanium coatings on the cutters
  • Lists plastics, aluminum, circuit board and wood as materials

Cons

  • No warranty term is stated
  • The 800 minutes of continuous machining is a maker claim with no condition stated
  • Cutting diameters span two sub-sets, so each bit needs checking
  • No speeds or feeds are stated
Shars 3/16" -3/4" HSS Single End Mill Set

Shars 3/16" -3/4" HSS Single End Mill Set

Shars9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 20-piece HSS set from 3/16 to 3/4 inch, with 2-flute and 4-flute square end cutters, center cutting and TiN coating.

Pros

  • Sizes from 3/16 to 3/4 inch in one set
  • 2-flute and 4-flute cutters in the same box
  • Center cutting square ends for plunging
  • Weldon flat shanks in 3/8, 1/2, 5/8 and 3/4 inch

Cons

  • No warranty term is stated
  • Cut lengths and overall lengths are given as ranges, so each size needs checking
  • Single end only, with one cutting end on each cutter
  • No recommended materials are listed
SpeTool 5PCS 2 Flutes Square Nose End Mill Set

SpeTool 5PCS 2 Flutes Square Nose End Mill Set

SpeTool9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-piece set of 2-flute solid carbide square nose end mills on a 1/4 inch shank, TiAlN coated for HRC 55, with a 3/4 inch cutting length.

Pros

  • Solid carbide with TiAlN coating for HRC 55
  • Lists steel, Inconel, stainless steel and titanium alloy
  • 1/4 inch shank fits routers with a 1/4 inch collet
  • Suits side milling, end milling and finish machining

Cons

  • No warranty term is stated
  • One cutting diameter only, 1/4 inch, across all 5 pieces
  • Square nose only, with no ball nose in the set
  • No speeds or feeds are stated
Home of quality tools 6pcs 1/2 inch 3/8 inch 5/16

Home of quality tools 6pcs 1/2 inch 3/8 inch 5/16

Home of quality tools9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 6-piece set of 4-flute carbide square end mills from 1/8 to 1/2 inch, with AlTiN coating and HRC 45 carbide.

Pros

  • 6 sizes from 1/8 to 1/2 inch in one set
  • 4-flute micro grain carbide for hard materials
  • AlTiN coating for high temperature stability and low friction
  • Chamfered shanks for faster tool changes

Cons

  • No warranty term is stated
  • Square end only, with no ball nose in the set
  • No material list is stated beyond hard materials
  • Shank diameter is not stated apart from the cutting sizes

End mill types in one paragraph

An end mill cuts with flutes that run along its side and across its end. A flat nose leaves a flat bottom with a sharp corner, a ball nose leaves a round bottom for curved pockets and sculpted shapes, and a square end is a flat nose with a square corner for slots and shoulders. Flute count sets how the cutter clears chips and how smooth the finish is: fewer flutes leave more room for chips, more flutes leave a finer edge. Shank size must match the collet, and coating sets how the edge holds up in hard material.

Side by side

Gear Score Flutes Shank Cutting diameter
Genmitsu MC40A 9.6/10 2-flute 1/8 in 0.8-3.175 mm
Shars 404-5901 9.6/10 2 and 4 flute 3/8 to 3/4 in 3/16 to 3/4 in
SpeTool 5-Piece Set 9.6/10 2-flute 1/4 in 1/4 in
Home 6-Piece Carbide Set 9.6/10 4-flute Not stated 1/8 to 1/2 in

Sizes in the table come from the listings for each set. Check the shank and cutting diameter in the listing before ordering, and match the shank to the collet on the machine.

Flat nose and square end mills

Flat nose and square end mills cut flat bottoms, slots and shoulders. The Genmitsu set pairs flat nose cutters with ball nose cutters in small diameters, while the Shars, Home and SpeTool sets are square end only. A square end leaves a sharp corner at the bottom of the cut, which suits pockets and slots that need a square edge. Center cutting ends, listed on the Shars set, can plunge straight down; a non-center cutting end needs a ramp or a drilled start hole.

Ball nose end mills

A ball nose end mill has a rounded tip that leaves a round bottom in the cut. It suits curved pockets, sculpted shapes and finishing passes where a sharp corner would leave a mark. The Genmitsu set is the only set here that includes ball nose cutters, paired with flat nose cutters on the same 1/8 inch shank. A ball nose is the wrong pick for flat bottoms, so keep it for curves and finish flat work with a flat nose.

Flute count and finish

Flute count is a trade between chip room and finish. A 2-flute cutter leaves wide flutes that clear chips fast, which suits soft material and deep slots. A 4-flute cutter has more cutting edges in the same diameter, which leaves a finer finish and suits harder material. The Genmitsu and SpeTool sets are 2-flute, the Home set is 4-flute, and the Shars set mixes 2-flute and 4-flute cutters across its sizes. Match the flute count to the material and the cut, not to the brand.

Shank sizes and collets

The shank is the part the collet grips, and it must match the collet on the machine. The Genmitsu set runs on a 1/8 inch shank for desktop CNC machines, the SpeTool set on a 1/4 inch shank for routers and CNC machines, and the Shars set spans 4 shank sizes from 3/8 inch to 3/4 inch. The Home set lists cutting diameters from 1/8 to 1/2 inch with no shank size stated apart from the cutters. Measure the collet before ordering, and read the end mill sizes chart for diameter and shank pairings.

Coatings: Nano Blue, Titanium, TiN and TiAlN

Coating is a thin layer on the cutter that the maker adds for hardness and heat resistance. The Genmitsu set pairs Nano Blue coating with Titanium coating, and the listing credits the coatings with keeping the cutting edge sharp. The Shars set is TiN coated, the Home set is AlTiN coated for high temperature stability and low friction, and the SpeTool set is TiAlN coated for HRC 55 work. Coating does not change the nose shape or the flute count, so pick the type first and treat coating after the type.

The sets that cover these types

The sets below cover the types above, from small diameter flat nose and ball nose cutters for desktop CNC work to square end sets in larger diameters for milling machines and routers, with each card noting the nose shape, flute count, shank and coating from its own listing.

FAQ for welders

What is the difference between a flat nose and a ball nose end mill?

A flat nose leaves a flat bottom with a sharp corner, while a ball nose leaves a round bottom. Flat nose cutters suit slots, shoulders and flat pockets; ball nose cutters suit curved pockets and finishing passes where a round bottom is wanted. The Genmitsu set in this guide includes flat nose and ball nose cutters.

How many flutes should an end mill have?

It depends on the material and the cut. A 2-flute cutter clears chips well in soft material and deep slots, while a 4-flute cutter leaves a finer finish and suits harder material. The sets here cover each count: the Genmitsu and SpeTool sets are 2-flute, the Home set is 4-flute, and the Shars set mixes 2-flute and 4-flute cutters.

What size end mill fits a desktop CNC?

Match the shank to the collet on the machine. The Genmitsu set runs on a 1/8 inch shank and lists desktop CNC machines, including the Genmitsu 3018 Series, as compatible. Check the collet size on the machine before ordering, and pick a cutting diameter that suits the detail of the work.

Can an end mill cut steel?

Yes, with the right cutter and coating. The SpeTool set lists steel, Inconel, stainless steel and titanium alloy, with TiAlN coating for HRC 55. The Shars set is HSS with TiN coating, and the Home set is HRC 45 carbide. Match the cutter to the metal, and check the listing for the material before ordering.

What does TiAlN coating do on an end mill?

TiAlN is a coating the maker adds for hardness and heat resistance. The Home set credits its AlTiN coating with high hardness, good high temperature stability and low friction. The SpeTool set is TiAlN coated for HRC 55 work. Coating does not change the nose shape or flute count, so it follows the choice of type.

Related: best end mill set, carbide vs HSS end mill, end mill sizes, best 1/4 inch end mill for CNC, and the metal fab tools hub.

More buying guides

Metal Fab Tools ·

End Mill Sizes: Diameter and Shank Chart

End mill sizes run from 1/8 inch to 3/4 inch in the sets here, and this guide maps cutting diameters, shank sizes, cut lengths…