End Mill Sizes: Diameter and Shank Chart
End mill sizes run from 1/8 inch to 3/4 inch in the sets here, and this guide maps cutting diameters, shank sizes, cut lengths and coatings for CNC and benchtop mills.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Shars 3/16" - 3/4" HSS Single End Mill Set9.7/10View on Amazon - 2
6Pcs Carbide Square End Mill Set 4-Flute TIALN9.6/10View on Amazon - 3
5pcs 1/4”, 3/8”, 1/2”, 5/8”9.6/10View on Amazon - 4
Home of quality tools 5PCS 1/2'' Carbide Square9.5/10View on Amazon
A slot that needs a flat bottom, a pocket with square corners and a profile edge all start with the same choice: which end mill size to put in the spindle. The size is the cutting diameter, and it decides the width of the cut in a single pass. End mill sizes run from small diameters for fine work to larger diameters for heavy cuts, and this guide maps the diameters and shanks in the sets below.
This guide links to product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same.

Shars 3/16" - 3/4" HSS Single End Mill Set
A 10-piece HSS set covering 3/16 inch to 3/4 inch cutters on 4 shank sizes, with 4 flutes, center cutting and a Weldon flat shank.
Pros
- 10 sizes from 3/16 inch to 3/4 inch in one set
- 4 shank sizes: 3/8, 1/2, 5/8 and 3/4 inch
- Center cutting square end mills with a Weldon flat shank
- Cut lengths from 1/2 inch to 1-5/8 inch
Cons
- HSS and uncoated, not carbide
- No warranty term is stated
- No stated coating or heat resistance figure

6Pcs Carbide Square End Mill Set 4-Flute TIALN
A 6-piece carbide set from 1/8 inch to 3/8 inch with 4 flutes, TiAlN coating and a 35°–38° helix angle for precision milling.
Pros
- 6 sizes from 1/8 inch to 3/8 inch in one set
- TiAlN coating with heat resistance up to 800℃
- Micrograin carbide for hardened steels and alloys, per the listing
- 35°–38° helix angle for clean finishes, per the listing
Cons
- No warranty term is stated
- Largest cutter is 3/8 inch, so no larger sizes in the set
- No stated shank sizes
- No stated cut lengths

5pcs 1/4”, 3/8”, 1/2”, 5/8”
A 5-piece carbide set covering 1/4 inch to 3/4 inch with 4 flutes and AlTiN coating, each cutter packed in a separate plastic box.
Pros
- 5 sizes from 1/4 inch to 3/4 inch in one set
- AlTiN coating for hot hardness and oxidation resistance, per the listing
- HRC 45, per the listing title
- Each cutter packed in a separate plastic box
Cons
- No warranty term is stated
- No stated shank sizes
- No stated cut lengths
- Smallest cutter is 1/4 inch, so no smaller sizes in the set

Home of quality tools 5PCS 1/2'' Carbide Square
A pack of 5 carbide square end mills, all 1/2 inch, with 4 flutes and AlTiN coating for alloy and hardened steels.
Pros
- 5 cutters of the same 1/2 inch size for repeat work
- Micro grain carbide with AlTiN coating, per the listing
- HRC 45 for pre-hardened and hardened steels, per the listing
- 4 flutes for shallow slots, profile milling and finish machining, per the listing
Cons
- Single size only, no other diameters in the pack
- No warranty term is stated
- No stated shank size
- No stated cut length
End Mill Sizes: Diameter and Shank
An end mill is sized by the cutting diameter and the shank diameter. The cutting diameter is the width the tool cuts. The shank is the part the collet or holder grips. The Shars set shows the pair at once: cutters from 3/16 inch to 3/4 inch sit on shanks of 3/8 inch, 1/2 inch, 5/8 inch and 3/4 inch, with the smaller cutters on the 3/8 inch shank.
Common End Mill Sizes in the Sets
The sets here cover cutting diameters from 1/8 inch to 3/4 inch. The Pro Edge set runs 1/8 inch, 3/16 inch, 1/4 inch, 5/16 inch and 3/8 inch. The Shars set adds 7/16 inch, 1/2 inch, 9/16 inch, 5/8 inch, 11/16 inch and 3/4 inch. The carbide set from Home of Quality Tools covers 1/4 inch, 3/8 inch, 1/2 inch, 5/8 inch and 3/4 inch. The other set from the same maker holds 1/2 inch cutters only, in a pack of 5.
Cut Length and Overall Length
Cut length is how deep the flutes cut, and overall length is the full tool from tip to shank end. The Shars set states cut lengths from 1/2 inch to 1-5/8 inch and overall lengths from 2-3/8 inch to 3-7/8 inch. Make sure the cut length covers the depth of the slot or pocket, and check the overall length against the holder and the work.
Flutes, Coating and Material
All 4 sets here are 4 flute square end mills. The carbide sets carry AlTiN or TiAlN coatings. The AlTiN listings state hot hardness and oxidation resistance, and the TiAlN coating on the Pro Edge set states heat resistance up to 800℃ and oxidation resistance. The HSS Shars set is uncoated. The 1/2 inch AlTiN pack states HRC 45 for pre-hardened and hardened steels.
Replacement End Mills for Your Mill
The sets below cover the sizes in this guide: a 10-piece HSS range for general milling, carbide sets for steels, and a pack of 1/2 inch cutters for repeat work. Match the cutting diameter and shank to your holder before ordering.
Side by Side
| Gear Score | Sizes | Material | Flutes | |
|---|---|---|---|---|
| Shars 3/16 to 3/4 Inch HSS End Mill Set | 9.7/10 | 3/16 to 3/4 in, 10 sizes | HSS, uncoated | 4 |
| Pro Edge 1/8 to 3/8 Inch Carbide End Mill Set | 9.6/10 | 1/8 to 3/8 in, 6 sizes | Carbide, TiAlN | 4 |
| Home of Quality Tools 1/4 to 3/4 Inch Carbide Set | 9.6/10 | 1/4 to 3/4 in, 5 sizes | Carbide, AlTiN | 4 |
| Home of Quality Tools 1/2 Inch Carbide Set | 9.5/10 | 1/2 in, 5 pieces | Carbide, AlTiN | 4 |
FAQ for welders
What end mill size do I need for a slot?
Match the cutting diameter to the slot width. The sets here run from 1/8 inch to 3/4 inch, so pick the diameter that matches the slot and check the shank against the holder.
Does the shank have to match the cutting diameter?
No. The Shars set shows cutters from 3/16 inch to 3/4 inch on shanks of 3/8 inch, 1/2 inch, 5/8 inch and 3/4 inch, so a small cutter can sit on a larger shank. Check the shank size against the collet or holder.
What is the difference between carbide and HSS end mills?
The listings state carbide has higher hardness and wear resistance than high-speed steel, and the carbide sets here carry AlTiN or TiAlN coatings. The Shars set is HSS and uncoated. Pick carbide for the steels the listings name.
How many end mills are in a set?
The sets here hold 5, 6 or 10 pieces. The Shars set holds 10 pieces, the Pro Edge set holds 6 pieces, and each carbide set from Home of Quality Tools holds 5 pieces.
Related: best carbide burr for aluminum, best tungsten carbide rotary file, die grinder uses, and the metal fab tools hub. Also see angle grinder parts.




