Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Angle Grinder Parts: Guards, Discs, Brushes and Spares

Angle grinder parts are mostly flange nuts, lock nuts and wrenches: this guide explains each part, the 5/8-11 sizes the listings state, and how to check fit.

Angle Grinder Parts: Guards, Discs, Brushes and Spares
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 16" Wire Wheel for Bench Grinder6" Wire Wheel for Bench Grinder9.6/10View on Amazon
  2. 2OSFTBVT 6in Wire Wheel Brush for Bench GrinderOSFTBVT 6in Wire Wheel Brush for Bench Grinder9.6/10View on Amazon
  3. 36" Bench Grinder Wheel 60 Grit & Wire Wheel Brush with 1/2"6" Bench Grinder Wheel 60 Grit & Wire Wheel Brush with 1/2"9.6/10View on Amazon

Angle grinder parts are the wear items and spares around the spindle, plus the wrench that changes them: flange nuts, lock nuts, guards and discs. An angle grinder is a motor, a spindle, a guard and a disc held on by a flange nut. This guide names each part, the sizes the listings state and what to check before ordering a spare.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

The parts in one paragraph: angle grinder parts

The flange nut threads onto a 5/8-11 shaft and clamps the disc against the inner flange. The listings in this guide state 5/8-11 nuts for 4-1/2, 5 and 7 inch grinders, with 1 wrench and 6 nuts in the 7-piece kits: 3 inner flange nuts and 3 outer flange nuts. A pin spanner or adjustable wrench loosens the lock nut for a disc change, and the guard sits between the disc and the user. Carbon steel is the material the listings name for the nuts, and several listings note its heat dissipation.

Side by side

Part Thread Fits Notes
Flange nut, inner 5/8-11 4-1/2, 5, 7 in grinders Sits under the disc
Flange nut, outer (lock nut) 5/8-11 4-1/2, 5, 7 in grinders Holds the disc on the shaft
Pin spanner / wrench Not stated Nuts for 4-1/2, 5, 7 in grinders Loosens and tightens the lock nut
Adjustable wrench Not stated Nuts for 4-1/2, 5, 7 in grinders Fits multiple nut sizes
Storage box Not stated 9-piece kit Keeps nuts and wrench in order

Thread sizes are as the listings state them. Always verify the shaft is 5/8-11 threaded and free of shaft-end bosses before ordering, as the listings state.

When a flange nut kit is the better choice

  • Lost wrench. The HOBEREROK adjustable kit lists a wrench plus 4 nuts for lost or missing wrenches, so a kit puts the wrench back in hand.
  • Worn nuts. Carbon steel nuts with heat dissipation are the material the listings name, and a fresh set threads on clean.
  • Spare nuts on hand. The IALTMEI listing states spare nuts avoid downtime, and the 7-piece kits carry 3 inner and 3 outer nuts.
  • Fast disc changes. The pwkauka kit (on Amazon) lists its wrench and nuts for quick wheel changes and arbor nut replacement on 4-1/2, 5 and 7 inch grinders.
  • More nuts, spanners in the box. The DIRBUY kit lists 6 inner and 6 outer nuts with 2 spanners, so the count suits a shop that changes discs often.

Our angle grinder uses guide covers cutting, grinding and stripping jobs for these discs.

When a nut-only kit is the better choice

  • Wrench already in hand. The DEHOMKUS kit (on Amazon) lists nuts only and states no extra tools are required beyond the grinder wrench, so a welder with a wrench buys nuts alone.
  • Model match. The DEHOMKUS listing names models such as 193465-4, 9029, 9069 and 9016DB, so match the model number before ordering.

See the Metabo vs Ryobi angle grinder comparison for the grinders these nuts fit.

How to tell what fits your grinder

Start with the thread: the listings state 5/8-11 nuts for 4-1/2, 5 and 7 inch grinders. Next, check the brand and model: the listings name Dewalt, Milwaukee, Makita, Ryobi, Bosch, Metabo, Black & Decker and Craftsman, with model numbers such as 193465-4 and DWE402 in the fit lists. Then check the Milwaukee 4-1/2 inch question: several listings state the nuts do not fit Milwaukee 4-1/2 inch models, while the HOBEREROK listing names a Milwaukee M18 FUEL 4-1/2 inch grinder as fitting, so check the model number on the listing against the grinder in hand. Count the pieces too: the DIRBUY 12-piece (on Amazon) kit lists 14 pieces in its bullets and spec table, so read the bullets, not the title alone. Verify the shaft is 5/8-11 threaded and free of shaft-end bosses before ordering.

Guards, discs and brushes

The listings in this guide cover nuts and wrenches, not guards, discs or brushes, so those parts need their own check. The guard is the part between the disc and the user, and it stays on the grinder. The disc is the part that cuts and grinds, and it wears down with use. Brushes sit inside the motor and wear with hours of use. For each of these, match the part to the grinder model and the disc size, and check the disc label and the grinder manual before fitting a new part.

Which brands do the nuts fit

The listings name Dewalt, Milwaukee, Makita, Ryobi, Bosch, Metabo, Black & Decker and Craftsman across the kits. The HOBEREROK listing names Dewalt DCG412, D28402, DWE4011 and DWE402, Milwaukee M18 FUEL 4-1/2 inch Brake Grinder 2980-20 and Makita 9005B, 9015DB and 9557NB. The DEHOMKUS listing names 193465-4, 9029, 9069, 9016DB, 9047L, 9558NB and 9557PB, plus 10.5A 5 inch and 15A 9 inch grinders. Fit lists differ from kit to kit, so check the model number on the listing against the grinder in hand before ordering.

Grinder safety. Unplug the grinder before changing a disc, keep the guard in place, and wear eye and hearing protection. A loose lock nut lets the disc wobble, so tighten the nut with the wrench and check it before the grinder runs. Keep the work area clear of flammable material, and check the disc label and the grinder manual for the disc and the grinder. See the OSHA welding overview.

FAQ for welders

What size flange nut does an angle grinder use?

The listings in this guide state 5/8-11 nuts for 4-1/2, 5 and 7 inch grinders. Verify the shaft is 5/8-11 threaded and free of shaft-end bosses before ordering, as the listings state.

Do flange nuts fit Milwaukee grinders?

Most listings name Milwaukee among the brands, but several state the nuts do not fit Milwaukee 4-1/2 inch models. The HOBEREROK listing names a Milwaukee M18 FUEL 4-1/2 inch grinder as fitting, so check the model number against the listing.

What is the difference between an inner and an outer flange nut?

The inner flange sits on the shaft under the disc and the outer lock nut threads on over the disc to hold it. The kits in this guide include 3 inner and 3 outer nuts, or 2 inner and 2 outer nuts in the smaller kits.

Can I change a grinding disc without a wrench?

No. The lock nut needs the pin spanner or adjustable wrench the kit includes, and the listings state no extra tools are needed beyond that wrench. Unplug the grinder before changing the disc, and keep the guard in place.

How many spare nuts should I keep?

The kits include 6 nuts or 4 nuts with 1 wrench, so a kit leaves spares on hand. The IALTMEI listing states spare nuts avoid downtime.

Related: best angle grinder for car restoration, Bosch vs Milwaukee angle grinder, angle grinder vs rotary tool, and the metal fab tools hub.

More buying guides