Die Grinder Parts: Collets, Bits and Accessories
Die grinder parts are the collets, mandrels, wheels and bits that make the tool cut, grind and sand. What each part does, which sizes fit, and the four sets that cover the work.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
HOMO FABER 50Pcs Die Grinder Sanding Discs9.6/10View on Amazon - 2
Panlen 3 Inch 10 Pack Die Grinder Cutting Disc9.5/10View on Amazon - 3
AOKLIT 4 Pack Cut Off Wheel Mounting Mandrel9.4/10View on Amazon - 4
WORKPRO 698-Piece Rotary Tool Accessories Kit9.4/10View on Amazon
The die grinder spins, the bit is loaded, and the collet is the part that holds it all together. Die grinder parts are the pieces that make that spin useful: collets that grip the shank, mandrels that carry cutoff wheels and discs, and the wheels, discs and bits that cut, grind and sand. This guide covers what each part does and the four sets here that cover the work.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

HOMO FABER 50Pcs Die Grinder Sanding Discs
Quick-change 2 in flap discs in 36, 60, 80 and 120 grit, with 2 holders, for grinding, stripping, rust removal and metal finishing.
Pros
- Four grits, 36 to 120, cover removal to polishing
- 2 quick-change holders with reinforced steel shafts
- Zirconia-coated fibers bite into rust and paint
- Maker claims quick-change saves 70% of setup time
Cons
- No stated warranty term
- 2 in discs suit small areas, not large panels
- No cutoff wheel in the set
- No collet in the set

Panlen 3 Inch 10 Pack Die Grinder Cutting Disc
A 10 pack of 3 in alumina abrasive cutoff discs with a matching mounting mandrel, 3/8 in arbor hole and 1/4 in stem.
Pros
- Alumina abrasive discs for long life and fast cutting
- Double fiberglass mesh for safety and durability
- Matching mandrel, 3/8 in arbor and 1/4 in stem
- Suits cast iron, steel and stainless steel cutting
Cons
- No stated warranty term
- One mandrel for 10 discs
- No sanding or grinding wheel in the kit
- 3 in discs suit small cuts, not long straight cuts

AOKLIT 4 Pack Cut Off Wheel Mounting Mandrel
A 4 pack of cutoff wheel mounting mandrels in 3/8 and 1/4 in arbor sizes, in A3 carbon steel with black plating.
Pros
- Two arbor sizes, 3/8 and 1/4 in, in one pack
- A3 carbon steel with black plating resists rust
- Fits Type 1 wheels from 0.035 to 1/4 in thick
- 1/4 in shank fits most grinders and rotary tools
Cons
- No wheels included; mandrels only
- No stated warranty term
- 1/4 in shank does not fit larger-shank tools
- All four mandrels share the same shank size

WORKPRO 698-Piece Rotary Tool Accessories Kit
A 698 piece rotary accessories kit with collets, mandrels, grinding stones, cutoff wheels, sanding bands and brushes in a storage case.
Pros
- 698 pieces for cutting, grinding, sanding and more
- 4 collets in 1/16, 3/32 and 1/8 in
- Sturdy storage box with a clear lid, 10-1/4 by 7-1/2 by 2-3/8 in
- Instruction manual included
Cons
- Collets run 1/16 to 1/8 in, not the 1/4 in standard
- No stated warranty term
- A general rotary kit, not a die grinder set
- Only 2 HSS grinding points among 698 pieces
Die grinder parts in one paragraph
A die grinder is a small high speed rotary tool, and its parts fall into three groups. The collet is the sleeve inside the nose that grips the shank of a bit or a mandrel; swap the collet and you change the shank size the tool takes. The mandrel is the shaft that carries a wheel or disc, with a shank on one end that the collet grips and a screw head on the other that holds the wheel. The working end is the wheel, disc or bit itself: cutoff wheels slice metal, flap discs sand, and grinding stones shape.
Die grinder parts for cutting, sanding and grinding
The four sets here cover the work in this guide: cutting with the Panlen discs (on Amazon), sanding with the HOMO FABER flap discs (on Amazon), mounting wheels with the AOKLIT mandrels (on Amazon), and a broad backup kit from WORKPRO.
Side by side
| HOMO FABER flap discs | Panlen cutoff kit | AOKLIT mandrels | WORKPRO 698-piece kit | |
|---|---|---|---|---|
| Pieces | 50 pieces, 2 holders | 10 pack, 1 mandrel | 4 mandrels | 698 pieces |
| Main job | Sanding and stripping | Cutting metal | Mounting wheels | Cutting, grinding, sanding |
| Arbor or shank | Quick-change holders | 3/8 in arbor, 1/4 in stem | 3/8 and 1/4 in arbors | Collets 1/16, 3/32, 1/8 in |
| Grit or wheel | 36, 60, 80, 120 grit | Alumina abrasive discs | Type 1 wheels 0.035 to 1/4 in | Stones, wheels, bands, bits |
How to match parts to the tool
- Match the shank to the collet. The WORKPRO kit (on Amazon)‘s collets run 1/16, 3/32 and 1/8 in, so they suit small rotary tools, not a 1/4 in die grinder shank.
- Match the arbor hole to the mandrel. The AOKLIT mandrels cover both 3/8 and 1/4 in arbor holes.
- Match the wheel thickness to the mandrel. The AOKLIT mandrels take Type 1 wheels from 0.035 to 1/4 in thick.
- Match the grit to the job. The HOMO FABER set runs 36, 60, 80 and 120 grit, from heavy removal to polishing.
FAQ for welders
What parts does a die grinder need?
A collet to grip the shank, a mandrel to carry the wheel, and the wheel, disc or bit that does the work.
What size collet does a die grinder use?
It depends on the shank: the mandrels here use a 1/4 in shank, while the WORKPRO collets are 1/16, 3/32 and 1/8 in.
Can I use cutoff wheels on a die grinder?
Yes, with a mandrel: the Panlen kit pairs 3 in wheels with a 1/4 in stem mandrel, and the AOKLIT mandrels mount wheels with 3/8 or 1/4 in arbor holes.
What grit flap disc should I start with?
Start coarse and step finer: 36 grit for heavy removal, 60 for smoothing, 80 for fine finishing and 120 for polishing.
Do I need safety glasses with a die grinder?
Yes. Cutting and grinding throw chips, sparks and dust, so wear safety glasses.
Related: die grinder uses, what is a die grinder, angle grinder arbor sizes, and the metal fab tools hub.




