Angle Grinder Arbor Sizes Chart
The kits in this guide are made for a 5/8-11 spindle thread, covering the flange nuts and extension shafts that fit it.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Gaquolam 5/8"-11 Angle Grinder Extension Shaft9.7/10View on Amazon - 2
QZATTCAEN Airway Buffing Wheel Extension Shaft9.6/10View on Amazon - 3
7PCS Angle Grinder Nut Angle Grinder Flange9.6/10View on Amazon - 4
Fyjbnh 7PCS Angle Grinder Nut Wrench Kit 5/8-119.6/10View on Amazon
On the bench, a disc that will not sit flat or a nut that will not thread on stops the job before it starts. Angle grinder arbor sizes decide which discs, nuts and accessories fit your grinder, and for the kits in this guide the number to match is the thread on the spindle. This guide explains that thread, how to check it, and the kits that fit it.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Gaquolam 5/8"-11 Angle Grinder Extension Shaft
A kit with 3 extension shafts in 3, 4 and 5.5 inch lengths, an adjustable wrench and 3 sets of 5/8-11 press plates.
Pros
- 3 shafts in 3, 4 and 5.5 inch lengths, usable singly or connected
- Adjustable wrench covers 0.6 to 2.1 inches, rubber-coated handle
- 3 sets of 5/8-11 press plates included in the kit
- 45# steel shafts with nickel plating, per the listing
Cons
- No warranty term is stated
- No weight is stated
- Lubricating oil on the nuts needs wiping, per the listing
- No stated length when the shafts are connected

QZATTCAEN Airway Buffing Wheel Extension Shaft
A 2-1/4 inch buffing wheel extension shaft for 5/8 inch thread grinders, with a dual-drive locking screw.
Pros
- Extends the mandrel so thicker buffing wheels fit
- Dual-drive locking screw takes a screwdriver or a wrench
- Steel screw shaft and washer, aluminum threads tube
- Fits polish wheels with a 5/8 inch arbor hole
Cons
- No warranty term is stated
- 1 set only, with no stated option to connect extenders
- Built for buffing wheels, not for grinding discs
- No stated maximum wheel thickness

7PCS Angle Grinder Nut Angle Grinder Flange
A 7-piece flange nut kit with wrench, 6 nuts and a storage bag for 4-1/2, 5 and 7 inch grinders.
Pros
- 1 wrench, 3 inner nuts and 3 outer nuts, plus a storage bag
- Hard carbon steel nuts for wear resistance, per the listing
- Fits 4-1/2, 5 and 7 inch grinders with a 5/8-11 threaded shaft
- Lists DeWalt, Milwaukee, Makita, Bosch, Black and Decker and Ryobi models
Cons
- No warranty term is stated
- Excludes Milwaukee 4-1/2 inch, M18, 18V and Makita cordless grinders, per the listing
- No stated thickness for the flange nuts
- Near identical to the Fyjbnh kit here

Fyjbnh 7PCS Angle Grinder Nut Wrench Kit 5/8-11
A 7-piece flange nut kit with wrench and 6 carbon steel nuts for 4-1/2, 5 and 7 inch grinders.
Pros
- 1 wrench, 3 inner nuts and 3 outer nuts in the set
- Carbon steel nuts for strength and wear resistance, per the listing
- Fits 4-1/2, 5 and 7 inch grinders with a 5/8-11 threaded shaft
- Lists DeWalt, Milwaukee, Makita, Bosch, Black and Decker and Ryobi models
Cons
- No warranty term is stated
- Does not fit Milwaukee 4-1/2 inch grinders, per the listing
- No storage bag is listed
Angle grinder arbor sizes: the 5/8-11 thread in this guide
The kits in this guide are all made for a 5/8-11 threaded spindle. The flange nut kits are listed for 4-1/2, 5 and 7 inch grinders with a 5/8-11 shaft, and the extension shafts are listed for grinders with a 5/8-11 thread.
Check the fit before ordering. The Fyjbnh kit (on Amazon) states it does not fit Milwaukee 4-1/2 inch grinders, and the Tiosamd kit lists the same exclusion plus Milwaukee M18 models 2680-20 and 2880-20, 18V grinders and Makita cordless grinders. Match the model first, since the nuts will not thread on otherwise.
Side by side
| Arbor thread | Fits | Kit contents | Material | |
|---|---|---|---|---|
| Gaquolam Extension Kit | 5/8-11 | 5/8-11 thread grinders | 3 shafts, wrench, plates | 45# steel, nickel plating |
| QZATTCAEN Buff Extender | 5/8-11 | 5/8 inch thread mandrel | 1 shaft set | Steel, aluminum |
| Tiosamd Flange Nut Kit | 5/8-11 | 4-1/2, 5 and 7 inch grinders | 1 wrench, 6 nuts, storage bag | Hard carbon steel |
| Fyjbnh Flange Nut Kit | 5/8-11 | 4-1/2, 5 and 7 inch grinders | 1 wrench, 6 nuts | Carbon steel |
All 4 kits here are made for a 5/8-11 thread.
How to check your grinder’s arbor
Read the spindle thread on your grinder, then match it to the nut or accessory: the listings in this guide state 5/8-11. For a buffing wheel, check the arbor hole too: the QZATTCAEN extender (on Amazon) fits polish wheels with a 5/8 inch arbor hole.
For an extension shaft, check the length you need. The Gaquolam kit (on Amazon) gives 3 shafts in 3 inch, 4 inch and 5.5 inch lengths, and the shafts connect for a longer reach. The QZATTCAEN extender gives a 2-1/4 inch tube for airway buffing wheels.
Grinder safety. Grinders throw sparks and debris, so wear eye and face protection, clamp the work, keep guards in place, and keep gloves away from rotating parts. OSHA machine guarding guidance covers guard use.
Flange nuts and extension shafts for angle grinder arbor sizes
The kits below handle the parts of the job that depend on the arbor: holding the disc, and reaching into tight spots with an extension shaft.
For more options, see our metal fab tools guides.
FAQ for welders
What arbor size do the kits in this guide fit?
The kits in this guide are made for a 5/8-11 thread. The flange nut kits are listed for 4-1/2, 5 and 7 inch grinders with that spindle. Check your grinder’s spindle thread before ordering.
Will these flange nuts fit a Milwaukee grinder?
Not every Milwaukee model. The Fyjbnh kit states it does not fit Milwaukee 4-1/2 inch grinders, and the Tiosamd kit also excludes Milwaukee M18 models 2680-20 and 2880-20 and 18V grinders.
What is an angle grinder extension shaft for?
It lengthens the spindle so a buffing wheel or disc can reach into narrow, tight or awkward places. The Gaquolam kit gives 3 shafts in 3 inch, 4 inch and 5.5 inch lengths, and the QZATTCAEN extender fits thicker buffing wheels on a 5/8 inch thread mandrel.
How many nuts come in a flange nut kit?
The Fyjbnh and Tiosamd kits each list 1 wrench and 6 nuts: 3 inner flange nuts and 3 outer flange nuts. The Tiosamd kit also includes a storage bag.
Can extension shafts be connected together?
The Gaquolam listing states you can use the 3 extension rods individually or connect them for a longer rod. The QZATTCAEN listing describes 1 extender set only.
Related: the arbor adapter guide, the best angle grinder picks, and angle grinders for cutting metal. Also see flap discs for angle grinders and grinding wheels.




