Best High Speed Steel End Mill (2026): 4 Picks Compared
Four high speed steel end mills for the shop, comparing single cutters and size sets by diameter, flutes, shank and coating.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallAFUNTA 10-Piece End Mill Set9.6/10View on Amazon - 2
Best Single Large CutterRannb 3/4 Inch End Mill9.6/10View on Amazon - 3
Best Small Single CutterRannb 5/16 Inch End Mill9.6/10View on Amazon - 4
Best 8-Piece SetOudtinz 8-Piece End Mill Set9.6/10View on Amazon
A small milling job stalls when the cutter on hand is the wrong size for the slot or the material fights the edge, and the best high speed steel end mill for the job is the cutter whose diameter, flutes and shank match the cut. We compared the cutters on what each listing states: cutting diameter, flute count, shank size, coating and what is in the box, so you can match the cutter to the cut.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Here is who each pick is for. The AFUNTA 10-piece set is our best overall pick for a hobby mill that cuts many diameters: it covers the most sizes in one purchase and is the only listing here that states a coating, so it answers the most jobs from one box. The Oudtinz 8-piece set is the other choice for a hobby mill that needs many diameters. The Rannb 3/4 inch and 5/16 inch cutters are single cutters for a known slot, so pick one only when you already know the width. One sizing point matters before you order: the two sets are metric, 2mm to 12mm, while the two singles are inch sizes.
Quick picks
- Best Overall AFUNTA 10-Piece End Mill Set: For a hobby mill that cuts many diameters: 10 metric sizes from 2mm to 12mm, the only listing here with a stated coating (TIAIN). Check price on Amazon
- Best Single Large Cutter Rannb 3/4 Inch End Mill: For a known 3/4 inch slot: 3/4 inch cutting diameter and shank, square end, center cutting, in a box. Check price on Amazon
- Best Small Single Cutter Rannb 5/16 Inch End Mill: For a known 5/16 inch slot: 5/16 inch cutting diameter and shank, flat end, in a box. Check price on Amazon
- Best 8-Piece Set Oudtinz 8-Piece End Mill Set: 8 metric sizes from 2mm to 12mm with a square end and 30 degree helix. Check price on Amazon
The machines

10 PCS 0.08" - 0.47" End Mills
A 10-piece set of 4-flute high speed steel end mills from 2mm to 12mm, with a TIAIN coating on the edges and a U-shaped groove design.
Pros
- 10 sizes from 2mm to 12mm in one set
- TIAIN coating on hard, sharp edges
- U-shaped groove design for chip removal
- Listing wording names steels, cast iron, titanium, wood and aluminum; confirm your material
Cons
- Metric sizes only, so inch holders and slots need checking
- No cutting length is stated for the set
- No case or box is stated for the set
- No warranty term is stated

End Mill 4-Flute CNC Milling Bit 3/4" Cutting Dia
A single 4-flute high speed steel end mill with a 3/4 inch cutting diameter and shank, a square end, center cutting and a plastic box.
Pros
- 3/4 inch cutting diameter with a 3/4 inch shank
- Square end with center cutting
- 35 degree helix angle
- Plastic box included for protection and transport
Cons
- Single cutter only, not a set
- No warranty term is stated
- Finish is listed as unfinished, with no coating stated
- No safety certification is stated

End Mill 5/16" Cutting Dia 5/16" Shank 4-Flute CNC
A single 4-flute high speed steel end mill with a 5/16 inch cutting diameter and shank, a flat end, center cutting and a plastic box.
Pros
- 5/16 inch cutting diameter with a matching 5/16 inch shank
- Flat end with center cutting
- Premium high speed steel, with high toughness per the maker
- Plastic box included for protection and transport
Cons
- Single cutter only, not a set
- No warranty term is stated
- Finish is listed as unfinished, with no coating stated
- Title names only wood, steel and aluminum for materials

8Pcs End Mill Bits HSS CNC End Mill Cutter Drill
An 8-piece set of 4-flute high speed steel end mills from 2mm to 12mm, with a square end, center cut and a 30 degree helix angle.
Pros
- 8 sizes from 2mm to 12mm in one set
- Square end with center cut
- 30 degree helix angle
- Ultra-fine steel bar stated for bending and abrasion resistance
Cons
- No warranty term is stated
- No case or box is stated for the set
- Metric sizes only, so inch holders and slots need checking
- No coating is stated
Other welders and gear to compare
2pcs End Mill Set 4-Flute CNC Milling Bit 10mm/0.4" CuttingCheck price on Amazon
SPEED TIGER EISE 1/8" Carbide Square End MillCheck price on Amazon
SPEED TIGER EISE 1/4" Carbide Square End MillCheck price on Amazon
8PCS HSS 4-Flute End Mill Set CNC Milling Bits 1/16''-1/2''Check price on Amazon
5PCS 1/4 inches Carbide Square End Mill Bits SetCheck price on Amazon
5/16 Inch Shank Carbide Square End MillCheck price on Amazon
Spec sheet comparison
| End mill | Gear Score | Cutting diameter | Flutes | Shank | Sizes |
|---|---|---|---|---|---|
| AFUNTA 10-Piece End Mill Set | 9.6/10 | Up to 12 mm | 4 | Straight | 10 sizes |
| Rannb 3/4 Inch End Mill | 9.6/10 | 0.75 inch | 4 | 3/4 inch | 1 cutter |
| Rannb 5/16 Inch End Mill | 9.6/10 | 5/16 inch | 4 | 5/16 inch | 1 cutter |
| Oudtinz 8-Piece End Mill Set | 9.6/10 | Up to 12 mm | 4 | Straight | 8 sizes |
These numbers are the manufacturer’s ratings exactly as each listing gives them, recorded on 28 October 2026.
Buying guide: choosing the best high speed steel end mill
Diameter and shank size
The diameter sets the slot width and the shank sets the holder, so both numbers have to match the job. The single cutters state one diameter each: the Rannb 3/4 inch cutter with a 3/4 inch shank, and the Rannb 5/16 inch cutter with a 5/16 inch shank. The two sets state straight shanks from 2mm to 12mm, so one set covers many diameters where a single cutter covers one. Check the shank against the collet or chuck before ordering, since the listings state the shank size but not the holder.
Flutes and end shape
All four listings state 4 flutes. The Rannb 5/16 inch listing states that 4 flutes give a better finish than fewer flutes, and lists planar, step, groove and forming work for that cutter. The Rannb 3/4 inch cutter and the Oudtinz set state a square end, while the Rannb 5/16 inch cutter states a flat end; both end shapes suit flat-bottom work. All three of those listings also state center cutting, which suits plunging into the workpiece as well as side work.
Coating and material range
Only the AFUNTA set lists a coating: a TIAIN coating on hard, sharp edges. The other three listings state no coating, and the Rannb 3/4 inch listing states an unfinished finish. The material ranges below are each listing’s own wording, not a promise that a cutter suits every material. All four are 4-flute high speed steel cutters, so confirm your material against the cutter you pick before cutting. The Rannb 3/4 inch listing names wood, aluminum, copper, stainless steel, cast iron and plastic, while the sets name steels, cast iron and titanium, with wood and aluminum in their titles.
Single cutters or a set
A single cutter suits a job where the diameter is already known, while a set suits a shop that cuts many sizes. The two Rannb singles each come with a plastic box for protection and transport, and each covers one diameter. The AFUNTA set covers 10 sizes and the Oudtinz set covers 8 sizes, both from 2mm to 12mm, so a set answers more jobs from one purchase. See our end mill high speed steel hub for more tools in this class.
What is in the box
The two single Rannb cutters each state one end mill plus one plastic box. The AFUNTA and Oudtinz set listings state the cutter counts but state no box or case, so plan storage separately if the set matters to you. A box keeps a single cutter from rolling around a drawer and protects the edge between jobs.
Before You Strike an Arc
- Match the shank to the collet or chuck before cutting: the singles state 3/4 inch and 5/16 inch shanks, and the sets state straight shanks from 2mm to 12mm.
- Check the cutter on arrival against the listing: diameter, flute count and end shape.
- Confirm the material range in the listing covers your workpiece before cutting.
- Keep the plastic box with the single cutters for protection and transport.
FAQ for welders
What is a square end mill?
A square end mill is listed with a square end, meaning the end is flat rather than rounded. The Rannb 3/4 inch cutter and the Oudtinz set state square ends, while the Rannb 5/16 inch cutter states a flat end. A flat end suits flat-bottom slots and surfaces.
Are these end mills carbide?
No. Each listing here states high speed steel, not carbide. Compare these cutters on their stated diameters, flutes and shanks rather than on carbide performance, which no listing here claims.
What sizes do the sets cover?
The AFUNTA set covers 2mm to 12mm in 10 sizes, and the Oudtinz set covers 2mm to 12mm in 8 sizes. The single cutters cover one diameter each: 3/4 inch and 5/16 inch. Pick the set when the job needs many diameters, and a single cutter when the diameter is already known.
Do these end mills come with a case?
The two single Rannb cutters each come with a plastic box, per their listings. The AFUNTA and Oudtinz set listings state no case or box. If storage matters, plan a case for the sets before ordering.
What materials can these end mills cut?
Each listing names its own materials, and the ranges differ. The Rannb 3/4 inch listing names wood, aluminum, copper, stainless steel, cast iron and plastic, and the sets name steels, cast iron and titanium, with wood and aluminum in their titles. All four are 4-flute high speed steel cutters, so confirm your material against the cutter before ordering.
Related: best end mill set, best drill bits for steel, best drill press for metalworking, and the metal fab tools hub.
Scoring, line by line
Each end mill is scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. No listing here states a safety certification or a warranty term, so every cutter here scores zero on those criteria; the ranking comes from performance, build and value.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| AFUNTA 10-Piece End Mill Set | 9.6 | 30 | 20 | 22 | n/a | 0 |
| Rannb 3/4 Inch End Mill | 9.6 | 30 | 21 | 20 | n/a | 0 |
| Rannb 5/16 Inch End Mill | 9.6 | 29 | 21 | 20 | n/a | 0 |
| Oudtinz 8-Piece End Mill Set | 9.6 | 29 | 20 | 20 | n/a | 0 |
Displayed scores fall between 9.2 and 9.8: the weighted point total is mapped onto that band in a straight line, so earning more points always lifts the score. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.




