Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Use a Sheet Metal Bender

How to use a sheet metal bender, from marking the bend line and setting the fold depth to holding the sheet and folding, with four hand tools scored for ductwork, roofing and shop bends.

How to Use a Sheet Metal Bender
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Klein Tools 86532 Metal Folding Tool for DuctKlein Tools 86532 Metal Folding Tool for Duct9.7/10View on Amazon
  2. 2HURRICANE 12 Inch Sheet Metal Folding ToolHURRICANE 12 Inch Sheet Metal Folding Tool9.6/10View on Amazon
  3. 3DURATECH 3 Inch Sheet Metal BenderDURATECH 3 Inch Sheet Metal Bender9.5/10View on Amazon
  4. 4IRWIN VISE-GRIP Original Locking Sheet Metal ToolIRWIN VISE-GRIP Original Locking Sheet Metal Tool9.5/10View on Amazon

A duct joint that will not close usually starts with a fold that landed off the mark. Learning how to use a sheet metal bender turns that job into a repeatable step: mark the line, set the depth, hold the sheet and fold.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Klein Tools 86532 Metal Folding Tool for Duct

Klein Tools 86532 Metal Folding Tool for Duct

KLEIN TOOLS9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An 18 x 3 inch folding tool with two set fold depths, sight gauges and a 1 year manufacturer warranty.

Pros

  • Two folding depths, 3/8 inch and 1 inch, for duct and flashing work
  • Folds up to 24 ga CRSM and 28 ga stainless steel
  • Sight gauges for depth alignment
  • 1 year manufacturer warranty

Cons

  • No stated limit for galvanized sheet
  • No handle grip detail stated
  • No storage or hanging feature stated
  • Wider sheet needs repositioning
HURRICANE 12 Inch Sheet Metal Folding Tool

HURRICANE 12 Inch Sheet Metal Folding Tool

HURRICANE9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 12 inch folding tool with 3/8 inch and 1 inch fold depths, square sight holes for alignment and a yellow powder coated A3 steel body.

Pros

  • Two folding depths, 3/8 inch and 1 inch, for ductwork
  • Square sight holes for depth alignment
  • A3 steel body with a rust resistant yellow powder coating
  • Ergonomic non-slip handle

Cons

  • No gauge capacity stated in the listing
  • No warranty term stated
  • 12 inch width suits shorter folds; longer edges need repositioning
  • No hanging hole or storage feature stated
DURATECH 3 Inch Sheet Metal Bender

DURATECH 3 Inch Sheet Metal Bender

DURATECH9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3 inch straight jaw hand seamer with 1/4 inch depth notches, a TPR handle and a safety lock.

Pros

  • Bends up to 30 ga cold rolled, 18 ga galvanized and 30 ga stainless sheet
  • 1/4 inch incremental notches on the jaw side for clamping depth
  • Non-slip pattern inside the jaws to stop the sheet slipping
  • TPR handle with an anti-slip pattern, safety lock and spring design

Cons

  • 3 inch jaw width suits short seams; long folds need repositioning
  • No warranty term stated
  • No item weight stated in the listing
  • No stated limit for sheet wider than the 3 inch jaws
IRWIN VISE-GRIP Original Locking Sheet Metal Tool

IRWIN VISE-GRIP Original Locking Sheet Metal Tool

IRWIN9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An 8 inch locking sheet metal tool in heat-treated alloy steel, with a turn screw to set pressure and a trigger release.

Pros

  • Locking jaws hold pressure after setting, for repetitive bends
  • Turn screw adjusts pressure to fit the work
  • Heat-treated alloy steel construction
  • Classic trigger release designed for maximum locking force

Cons

  • No gauge capacity stated in the listing
  • No fold depth or jaw width stated
  • No warranty term stated

How to use a sheet metal bender

Mark the bend line on the sheet, then pick the fold depth the job needs. The folding tools here offer two set depths, 3/8 inch and 1 inch, while the hand seamer marks clamping depth with 1/4 inch notches on the side of the jaws.

Slide the sheet into the jaws or into the folding tool’s opening gap and line the mark up with the sight holes or sight gauges.

Hold the sheet so it cannot slip: the non-slip pattern inside the hand seamer jaws grips the metal, and the locking tool holds its pressure after the turn screw is set.

Fold the sheet over in a smooth motion and check the fold against the mark before moving on to the next piece.

Match the tool to the sheet: the Klein tool folds up to 24 ga CRSM and 28 ga stainless steel, and the Duratech hand seamer bends up to 30 ga cold rolled sheet, 18 ga galvanized sheet and 30 ga stainless steel. The Hurricane and Irwin listings state no gauge limit.

Side by side

Gear Score Fold depths Max capacity Size
Klein Tools 86532 9.7/10 3/8 in and 1 in 24 ga CRSM, 28 ga stainless 18 x 3 in
HURRICANE 12 Inch Folding Tool 9.6/10 3/8 in and 1 in Not stated 12 in
DURATECH 3 Inch Hand Seamer 9.5/10 No fixed depth; 1/4 in notches 30 ga cold rolled, 18 ga galvanized, 30 ga stainless 3 in jaws
IRWIN VISE-GRIP 23 9.5/10 Not stated Not stated 8 in

Two of the four tools here are folding tools with the same set depths, 3/8 inch and 1 inch. The table above shows the stated depths, capacities and sizes side by side.

The gear for the job

The steps above need a tool that sets the fold depth or grips the sheet while you bend it, and the four tools below cover that work from short hand seams to long duct edges.

FAQ for welders

What gauge sheet metal can a hand bender fold?

It depends on the tool. The Klein folding tool folds up to 24 ga CRSM and 28 ga stainless steel, and the Duratech hand seamer bends up to 30 ga cold rolled, 18 ga galvanized and 30 ga stainless sheet. The Hurricane and Irwin listings state no gauge limit.

What is the difference between a folding tool and a hand seamer?

A folding tool sets a fixed fold depth: the folding tools here offer 3/8 inch and 1 inch depths with sight holes or sight gauges for alignment. A hand seamer grips the sheet in jaws, and the Duratech model has 3 inch jaws with 1/4 inch notches for clamping depth.

How is the fold depth set on a sheet metal bender?

Line the bend mark up with the sight holes on the Hurricane tool (on Amazon) or the sight gauges on the Klein tool. On the Duratech hand seamer, use the 1/4 inch notches marked on the side of the jaws to set the clamping depth before bending.

Can a sheet metal bender fold stainless steel?

The Klein tool folds up to 28 ga stainless steel and the Duratech hand seamer bends up to 30 ga stainless steel. The Hurricane and Irwin listings state no stainless limit.

Is a locking sheet metal tool needed as well as a folding tool?

Not for every job. A folding tool sets the depth and makes the bend, while a locking tool holds the sheet at a set pressure, which suits batches of the same bend. The Irwin tool (on Amazon) stays adjusted for repetitive use.

Related: how to use a tube bender, how to use a bead roller, best tin snips for sheet metal, best sheet metal shears, and the metal fab tools hub.

More buying guides