Best Band Saw Blades 44 7/8 (2026): 5 Picks Compared
5 bi-metal band saw blades sized 44-7/8 inches by 1/2 inch, compared on tooth count, stated material and pack size.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallFOXBC 14 TPI 5 Pack9.7/10View on Amazon - 2
Best Fine ToothFOXBC 24 TPI 3 Pack9.6/10View on Amazon - 3
Best Variable PitchYullSorom 10-14 TPI 3 Pack9.6/10View on Amazon
A portable band saw earns its keep where a larger saw cannot reach, cutting conduit, rod, angle and tube on site and in the shop. When a blade dulls or snaps mid cut, the work stops while the saw sits idle, so the replacement blade matters more than it looks. This guide compares best band saw blades 44 7/8 for portable saws, using only what each listing states about tooth count, material and pack size.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall FOXBC 14 TPI 5 Pack: M42 bi-metal, 14 TPI with a stated 5/16 to 1/2 inch material range, and a 5 Pack. Check price on Amazon
- Best Fine Tooth FOXBC 24 TPI 3 Pack: 24 TPI, M42 bi-metal with a stated weld design, in a 3 Pack. Check price on Amazon
- Best Variable Pitch YullSorom 10-14 TPI 3 Pack: 10-14 TPI hook teeth in M42 bimetal, stated for steel, copper and aluminum. Check price on Amazon
The machines

FOXBC 44-7/8 inch Portable Bandsaw Blades 14 TPI
A 44-7/8 inch by 1/2 inch M42 bi-metal blade at 14 TPI, stated for material from 5/16 inch to 1/2 inch thick, sold as a 5 Pack for portable band saws.
Pros
- Bi-Metal M42 High Speed Steel with precision machined teeth, as the listing states
- Stated material range from 5/16 inch to 1/2 inch thick, the only stated range here
- A 5 Pack, the largest pack count in this roundup
- Fit list names Milwaukee 48-39-0511 and DeWalt DW3982 among its fits
Cons
- No warranty term is stated in the listing
- No safety standard is stated in the listing
- Fit list names fewer saw models than the 24 TPI FOXBC listing

FOXBC 44-7/8-inch Bandsaw Blades 24 TPI
A 44-7/8 inch by 1/2 inch M42 bi-metal blade at 24 TPI, the finest tooth count here, with a stated weld design and heat resistance, sold as a 3 Pack.
Pros
- 24 TPI, the finest tooth count in this roundup
- Bi-Metal M42 High Speed Steel with heat resistance and a stated weld design
- Broad fit list, naming DeWalt DW3984, Milwaukee 48-39-0531 and 48-39-0534
- Item weight is stated in the spec table, unlike most listings here
Cons
- A 3 Pack, fewer blades per pack than the 5 Pack FOXBC listing
- No warranty term is stated in the listing
- No safety standard is stated in the listing

44-7/8-Inch x 1/2 Portable Bandsaw Blade 10-14
A 44-7/8 inch by 1/2 inch M42 bimetal blade with a 10-14 TPI hook teeth profile, stated for steel and non-ferrous metals such as copper and aluminum, sold as a 3 Pack.
Pros
- 10-14 TPI variable pitch with a hook teeth profile, as the listing states
- M42 bimetal with stated wear resistance, fatigue resistance and flexibility
- Stated for steel and non-ferrous metals such as copper and aluminum
- Broad fit list, naming Milwaukee 48-39-0551 and DeWalt DCS374B among its fits
Cons
- No stated material thickness range, unlike the FOXBC 14 TPI listing
- No warranty term is stated in the listing
- No safety standard is stated in the listing

Imachinist S4478121418 M42 44-7/8" x 1/2" x
A 44-7/8 inch by 1/2 inch M42 blade at 14/18 TPI with a spring steel backer and a stated welded joint, limited by its listing to soft metal only, sold as a 3 Pack.
Pros
- 14/18 TPI variable teeth profile, as the listing states
- M42 grade bi-metal with a spring steel backer, as the listing states
- Almost invisible welded joint, as the listing states
- 0.025 inch thickness, thicker than the 0.020 inch blades here
Cons
- Soft metal only: the listing warns against cutting aluminum and other non ferrous metal
- Warranty line names no concrete term, only a contact note for a wrong or defective blade

SHAFACE for Milwaukee 48-39-0531 44-7/8-Inch
A 44-7/8 inch bi-metal deep cut blade at 24 TPI for Milwaukee 48-39-0531, sold as a 3 Pack, with no bullets in its listing to confirm width, thickness or material beyond the title.
Pros
- 24 TPI, matching the finest tooth count in this roundup
- Bi-metal deep cut blade, as the title states
- Names Milwaukee 48-39-0531 in its title as the fit
- A 3 Pack, matching the pack count of most listings here
Cons
- No bullets in the listing to confirm width, thickness or material
- No stated application or material range beyond the title
- No warranty term is stated in the listing
- No safety standard is stated in the listing
Other welders and gear to compare
Imachinist S447812101420 Bandsaw Blades 44-7/8" x 1/2" xCheck price on Amazon
Imachinist S4478121820 Bandsaw Blades 44-7/8" x 1/2" x 18 TPICheck price on Amazon
Imachinist S4478122420 Bandsaw Blades 44-7/8" x 1/2" x 24 TPICheck price on Amazon
Imachinist S64514 Bi-Metal Band Saw Blades 64-1/2" X 1/2" XCheck price on Amazon
Imachinist S9312121014 Bi-Metal Band Saw Blades 93-1/2" XCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Length | Width | Thickness | TPI | Pack | Material |
|---|---|---|---|---|---|---|---|
| FOXBC 14 TPI 5 Pack | 9.7/10 | 44-7/8 in | 1/2 in | 0.020 in | 14 TPI | 5 Pack | Bi-Metal M42 |
| FOXBC 24 TPI 3 Pack | 9.6/10 | 44-7/8 in | 1/2 in | 0.020 in | 24 TPI | 3 Pack | Bi-Metal M42 |
| YullSorom 10-14 TPI 3 Pack | 9.6/10 | 44-7/8 in | 1/2 in | 0.020 in | 10-14 TPI | 3 Pack | M42 bimetal |
| Imachinist 14/18 TPI 3 Pack | 9.6/10 | 44-7/8 in | 1/2 in | 0.025 in | 14/18 TPI | 3 Pack | M42 |
| SHAFACE 24 TPI 3 Pack | 9.4/10 | 44-7/8 in | 0.5 in | 0.039 in | 24 TPI | 3 Pack | Bi-Metal |
All specs here repeat what the maker rates and the listing prints, copied down 29 October 2026.
Buying guide: best band saw blades 44 7/8
Tooth count
Tooth count sets the finish and the bite. The FOXBC 24 TPI blades carry the finest tooth count here, while the FOXBC 14 TPI blade suits material from 5/16 inch to 1/2 inch thick, as its listing states. Variable pitch blades, such as the YullSorom 10-14 TPI and the Imachinist 14/18 TPI, vary the tooth spacing along the blade. Match the tooth count to the stock on the bench, and check the listing for a stated material range before ordering.
Bi-metal M42 blades
The FOXBC, YullSorom and Imachinist listings state M42 bi-metal, while the SHAFACE title states bi-metal without naming a grade. FOXBC links its M42 steel to heat resistance, and YullSorom links its M42 bimetal to wear resistance and fatigue resistance. Imachinist adds a spring steel backer, which its listing links to blade life. Where a listing names no grade, judge it on the tooth count and pack size it does state.
Pack size
Pack size decides how soon a dull blade stops the job. The FOXBC 14 TPI listing comes as a 5 Pack, while the other listings come as 3 Pack sets. A larger pack suits a busy shop, while a smaller pack suits a saw that sees occasional use. Check the pack count in the listing title before ordering, since the spec table does not always agree.
Check the fit before ordering
Every blade here is listed at 44-7/8 inches long, and the listings that state a width give 1/2 inch. Fit lists still differ by listing. FOXBC names DeWalt DW3984 and Milwaukee 48-39-0531 among its fits, while YullSorom names Milwaukee 48-39-0551 and DeWalt DW3983 among its fits. Confirm the saw model against the listing fit list, and confirm the width against the saw manual, before ordering.
Thickness: trust the title and bullets
Several listings disagree with their own spec tables on thickness. The FOXBC and YullSorom bullets state 0.020 inch, while their spec tables list 0.039 inches. The Imachinist bullets state 0.025 inch. Where a listing disagrees with itself, this guide trusts the title and bullets over the spec table, and each review below names the clash.
Use as directed. Unplug the saw before changing a blade, keep hands clear of the teeth while seating the blade, and check that the blade tracks on the wheels before cutting. A coiled blade springs open with force, so open the pack away from the body and wear gloves and eye protection while handling a bare blade.
Before You Strike an Arc
- Confirm the saw takes a 44-7/8 inch blade before ordering, since every pick here is that length.
- Match the tooth count to the stock: the FOXBC 14 TPI listing states material from 5/16 inch to 1/2 inch thick.
- Check the blade on arrival for the stated weld joint and for the stated width and thickness.
- Keep a spare blade from the pack on hand, so a dull blade does not stop the job.
- Confirm the fit list names the saw model, such as DeWalt DCS374B or Milwaukee 48-39-0531, before the blade ships.
FAQ for welders
What does TPI mean on a band saw blade?
TPI counts the teeth along the blade. A 24 TPI blade carries finer teeth than a 14 TPI blade, and the variable pitch blades here, 10-14 TPI and 14/18 TPI, vary the spacing along the blade. Finer teeth suit thinner stock, while coarser teeth clear chips from thicker stock.
Which tooth count suits thin stock?
Only the FOXBC 14 TPI listing gives a stated material range: it lists material from 5/16 inch to 1/2 inch thick. For stock thinner than that range, the 24 TPI FOXBC and SHAFACE blades offer finer teeth. Check the listing for a stated range, and where none is stated, match the tooth count to the stock on hand.
Can these blades cut aluminum?
It depends on the listing. YullSorom states its blade cuts steel and non-ferrous metals such as copper and aluminum. Imachinist states the opposite limit: soft metal only, and it warns against cutting aluminum and other non ferrous metal. Read the stated application line before cutting non-ferrous stock.
Do all 5 blades fit the same saws?
All 5 blades share the 44-7/8 inch length, but their fit lists differ. FOXBC names DeWalt DW3984 and Milwaukee 48-39-0531, YullSorom names Milwaukee 48-39-0551 and DeWalt DW3983, and SHAFACE names Milwaukee 48-39-0531 in its title. Match the saw model to the fit list on the exact listing before ordering.
Why do the spec tables list a different thickness?
Several spec tables list 0.039 inches where the bullets state 0.020 inch. Where a listing disagrees with itself, this guide trusts the title and bullets over the spec table. The Imachinist bullets state 0.025 inch, and the SHAFACE listing gives no bullets, so its dimensions come from its spec table alone.
Related: metal fab tools, best band saw blade for metal, best band saw blade for stainless steel, best band saw blade for aluminum, bi-metal vs carbide band saw blade, variable pitch vs constant pitch band saw blade, and portable vs stationary band saw.
Scoring, line by line
Each blade is scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. No blade here states a safety standard, so the safety criterion does not change the ranking; the ranking comes from performance, build and value, with warranty where a listing states a concrete term. No listing here states a concrete warranty term, so warranty does not change the ranking either.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| FOXBC 14 TPI 5 Pack | 9.7 | 30 | 21 | 22 | n/a | 0 |
| FOXBC 24 TPI 3 Pack | 9.6 | 30 | 21 | 21 | n/a | 0 |
| YullSorom 10-14 TPI 3 Pack | 9.6 | 29 | 20 | 21 | n/a | 0 |
| Imachinist 14/18 TPI 3 Pack | 9.6 | 28 | 20 | 20 | n/a | 0 |
| SHAFACE 24 TPI 3 Pack | 9.4 | 24 | 18 | 19 | n/a | 0 |
A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Unpowered items with no stated safety features skip the safety line, and their score comes from the 90 points that are left.




