Band Saw Blade Repair: Fixing and Rejoining Blades
A snapped portable band saw blade leaves a choice between rejoining it and fitting a fresh one, and two 44-7/8 in bi-metal blades show what to measure before ordering.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
FOXBC Portable Bandsaw Blades 44-7/8" x 1/2" x9.6/10View on Amazon - 2
Frienda 5 Pack 44-7/8-inch Bandsaw Blades 44-7/8"9.6/10View on Amazon
A portable band saw stops mid-cut, the blade hangs loose in the guides, and the job waits until the blade is sorted. Band saw blade repair starts with a simple question: is this blade worth rejoining, or is it a replacement job? This guide answers that question, then shows the replacement blades that fit the same portable saws, so the repair ends with a blade back in the guides.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

FOXBC Portable Bandsaw Blades 44-7/8" x 1/2" x
A 44-7/8 by 1/2 by .020 inch portable band saw blade in bi-metal M42 high speed steel, with a 14/18 TPI pitch, sold as a 5-pack for DeWalt, Milwaukee, Makita, Wen and Bosch portable saws.
Pros
- 14/18 TPI variable pitch for metal cutting
- Bi-metal M42 high speed steel with heat resistance
- Fits DeWalt DW3986, Milwaukee 48-39-0561, Makita XBP02Z and Bosch GCB10-5
- 5-pack keeps spare blades on hand
Cons
- No stated warranty term
- Variable 14/18 TPI pitch, so the finish differs from a straight 18 TPI blade
- 44-7/8 inch length fits only saws that take that length
- Sold only as a 5-pack, so a single repair still means buying spares

Frienda 5 Pack 44-7/8-inch Bandsaw Blades 44-7/8"
A 44-7/8 by 1/2 by .020 inch portable band saw blade in bi-metal M42 steel, with a straight 18 TPI pitch, sold as a 5-pack for DW3983 and DCS374B portable saws.
Pros
- Straight 18 TPI pitch for a balance of speed and finish
- Bi-metal M42 steel with heat resistance
- Cuts mild steel, aluminum, copper and some plastics
- 5-pack of ready to install replacements
Cons
- No stated warranty term
- Names only DW3983 and DCS374B as fits
- 18 TPI straight pitch, not a variable pitch for mixed stock
- 44-7/8 inch length fits only saws that take that length
Band Saw Blade Repair: Rejoin or Replace
A blade that snaps at the weld is the case a shop sometimes rejoins, and the shop cuts the ends square before welding them back together. A blade with stripped teeth, a cracked body or a bent back is usually a replacement job, and so is a blade that has already been rejoined and snapped again. When the blade is done, the repair is a fresh blade of the same length, width and thickness, fitted to the same saw.
Measure the old blade before ordering: length, width and thickness, plus the tooth pitch. Both blades here measure 44-7/8 inches long, 1/2 inch wide and .020 inch thick, and both fit the portable saws named in their listings. A blade that is too long will not tension, and a blade that is too short will not reach the wheels, so match each figure. Check the saw manual for the tension setting and the guide adjustment.
Replacement blades for the repair
Both blades below share the same 44-7/8 by 1/2 by .020 inch size, so the choice comes down to tooth pitch and the saws each maker names.
Side by side
| Blade size | TPI | Material | Pack | |
|---|---|---|---|---|
| FOXBC 44-7/8 x 1/2 | 44-7/8 x 1/2 x .020 in | 14/18 | Bi-metal M42 high speed steel | 5 |
| Frienda 44-7/8 x 1/2 | 44-7/8 x 1/2 x .020 in | 18 | Bi-metal M42 | 5 |
Both blades are bi-metal M42 steel in a 5-pack, and both measure 44-7/8 by 1/2 by .020 inch. The FOXBC blade pairs a 14/18 TPI variable pitch with the longer compatibility list, while the Frienda blade runs a straight 18 TPI pitch and names DW3983 and DCS374B.
How to fit the new blade
Disconnect the power, open the wheel covers, and slip the old blade off the wheels and out of the guides. Set the new blade on the wheels with the teeth pointing the way the saw cuts, then close the covers and tension the blade to the setting the saw manual gives. Turn the wheels by hand first: the blade should track in the middle of the wheels and run true through the guides before power is restored.
For more options, see our metal fab tools guides.
FAQ for welders
Can a broken band saw blade be repaired?
Sometimes. A blade that snaps at the weld can be rejoined by a shop with the right equipment, while a blade with stripped teeth, a cracked body or a bent back is usually a replacement job. Both blades in this guide are fresh replacements in the same 44-7/8 by 1/2 by .020 inch size.
What size blade does a portable band saw take?
It depends on the saw, so measure the old blade or check the saw manual. Both blades here measure 44-7/8 inches long, 1/2 inch wide and .020 inch thick, and the FOXBC blade lists DeWalt DW3986, Milwaukee 48-39-0561 and Makita XBP02Z among its fits, while the Frienda blade lists DW3983 and DCS374B.
What does 14/18 TPI mean?
TPI means teeth per inch, and the FOXBC blade states a 14/18 TPI variable pitch, while the Frienda blade states a straight 18 TPI pitch. The Frienda maker says the 18 TPI design suits mild steel, aluminum, copper and some plastics.
How many blades come in a pack?
Both blades here come in a 5-pack, so a pack keeps spares on hand for the next break. The FOXBC pack is a 5-pack of 14/18 TPI blades, and the Frienda pack is a 5-pack of 18 TPI blades.
Do these blades cut metal?
Both are bi-metal M42 steel blades for portable band saws. The Frienda maker names mild steel, aluminum and copper as the metals it cuts, and the FOXBC maker states a bi-metal M42 high speed steel blade for portable band saw use.
Related: how to sharpen band saw blades, best band saw blades 44 7/8, chop saw vs band saw for metal, and the best band saw blade for aluminum.




