Bi-Metal vs Carbide Band Saw Blade: Which Should You Buy?
Bi-metal and carbide band saw blades compared for metal cutting: construction, tooth pitch and best uses, with four bi-metal listings ranked.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
VEVOR Double Head Sheet Metal Nibbler Cutter9.7/10View on Amazon - 2
EZARC Obsidian Carbide Reciprocating Saw Blades 6" 8TPI Thick9.7/10View on Amazon - 3
HORUSDY 6PCS 9-Inch 14TPI Bi-Metal Reciprocating Saw Blades9.6/10View on Amazon - 4
Morse Master Cobalt Bi-Metal Portable Band Saw Blade 44 7/8 xView on Amazon - 5
FOXBC 64-1/2 Inch Bi-Metal Bandsaw Blade Metal Cutting 10/14View on Amazon - 6
TWIN-TOWN 14-Inch 80 Teeth Metal Steel Cutting Saw Blade forView on Amazon - 7
Bosch BS5912-18MA 59-1/2 in. 18 TPI Metal-Cutting StationaryView on Amazon - 8
14 Inch 72T Metal Circular Saw BladeView on Amazon - 9
FOXBC 14 Inch Metal Steel Cutting Saw Blade 72 Tooth forView on Amazon
A bi-metal band saw blade welds high-speed steel teeth to a flexible steel backing, while a carbide band saw blade carries much harder carbide teeth on a steel body. Pick bi-metal for general metal cutting, the everyday choice in every listing here; pick carbide for harder stock and long production runs where the harder tooth earns its keep. One honest note up front: all four listings in this guide are bi-metal blades, so the carbide side is described in general terms and the ranked gear below is all bi-metal.
Other welders and gear to compare
Morse Master Cobalt Bi-Metal Portable Band Saw Blade 44 7/8 xCheck price on Amazon
FOXBC 64-1/2 Inch Bi-Metal Bandsaw Blade Metal Cutting 10/14Check price on Amazon
TWIN-TOWN 14-Inch 80 Teeth Metal Steel Cutting Saw Blade forCheck price on Amazon
Bosch BS5912-18MA 59-1/2 in. 18 TPI Metal-Cutting StationaryCheck price on Amazon
14 Inch 72T Metal Circular Saw BladeCheck price on Amazon
FOXBC 14 Inch Metal Steel Cutting Saw Blade 72 Tooth forCheck price on Amazon
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Bi-metal vs carbide band saw blade: what separates them
The difference is the tooth. A bi-metal blade joins two metals: a high-speed steel tooth edge for cutting and a flexible spring-steel back that bends around the saw’s wheels without snapping. The Lenox listing puts it plainly, calling its blades shatter resistant because the bi-metal construction bends and resists breaking. A carbide blade instead puts carbide, a much harder material, at the cutting edge. The harder tooth holds its edge longer in hard stock but the blade is stiffer, less forgiving of abuse, and generally the more expensive blade to buy and to replace.
Side by side
| Bi-metal (all 4 listings) | Carbide (not listed) | From the listings | |
|---|---|---|---|
| Construction | High-speed steel teeth welded to a flexible steel backing | Carbide teeth joined to a steel body | All four listings are bi-metal; none is carbide |
| Listed examples | Imachinist S64514 and S933414, Lenox 5-pack, MK Morse 3-pack | None | |
| Tooth pitch stated | 14 TPI, 10/14 TPI, 14/18 TPI | Not stated | Variable pitch on the S933414 and the MK Morse |
| Blade sizes stated | 44-7/8 x 1/2 in up to 93 x 3/4 in | Not stated | |
| Stated for | Soft ferrous metal, thin pipe and tube, any machinable metal | Not stated | |
| Pack sizes | Single blade, 3-pack, 5-pack | Not stated | |
| Origin stated | Made in the USA (MK Morse) | Not stated |
All specs here repeat what the maker rates and the listing prints. No carbide blade was among the listings, so the carbide column carries no stated figures.
When bi-metal is the better choice
Bi-metal is the better choice for general shop cutting: mild steel, carbon steel, aluminum and the mixed stock a home shop actually cuts. It tolerates the flexing a band saw demands, survives the occasional bind better than a brittle tooth, and the listings here show the value: 3-packs and 5-packs that keep a spare on hand. The MK Morse states a shock resistant cutting edge for any machinable metal, and the Imachinist S933414 is aimed at thin pipe and tube profiles where a flexible blade tracks well. If you are cutting common metals on a 4×6 or portable saw, bi-metal is the blade the listings keep offering.
When carbide is the better choice
Carbide is the better choice when the stock is hard enough to dull high-speed steel quickly, or when the saw runs long production cuts where edge life dominates the cost. The harder tooth stays sharp longer in difficult material, which is the whole trade: longer edge life against a stiffer, less forgiving blade. No carbide listing was provided here, so there is no stated tooth pitch, size or price to compare; treat this as the general case and read the carbide listing’s own figures before buying.
Tooth pitch and what the listings state
Tooth pitch decides the cut more than the brand does. The listings state 14 TPI on the Imachinist S64514 and the Lenox 5-pack, 10/14 TPI variable on the Imachinist S933414, and 14/18 TPI variable on the MK Morse. Variable pitch, like the 10/14 and 14/18 here, is stated to suit a broader range of stock: the S933414 listing says its 10/14 TPI suits thin pipe and tube profiles, and the MK Morse lists a variable tooth pitch for broader applications with reduced vibration. Three listings need a careful read: the S64514 spec table says 6 TPI against 14 TPI everywhere else, the S933414 table says 3/4 TPI against 10/14 elsewhere, and the MK Morse table says 3 teeth against 14/18 elsewhere; per this site’s rules the titles win in each case.
The gear: four bi-metal blades ranked
1. MK Morse Master Cobalt 3-pack. The top pick: a cobalt bi-metal portable blade, 44-7/8 x 1/2 x .020 with 14/18 TPI variable pitch, in a 3-pack. Shock resistant cutting edge stated for any machinable metal, reduced vibration for cut finish, and made in the USA. The listing names aluminum, carbon steel, stainless steel, metal and plastic as compatible materials, the widest stated range here.
2. Lenox 5-pack. The value pick: 44-7/8 x 1/2 x .020, 14 TPI, five blades in the box. High speed steel teeth for a strong, long lasting cutting edge per the bullets, shatter resistant bi-metal construction, and a Tuff Tooth design that reinforces the tooth. No warranty term is stated, and the spec table’s ‘Blend’ material type is vague; the bullets’ high-speed-steel-teeth description is the one to trust.
3. Imachinist S933414. The big-saw pick: M42 bi-metal, 93 x 3/4 x 0.035 with 10/14 TPI variable pitch, suited to 7 x 12 bandsaws and any saw taking that size. Stated for thin pipe and tube profiles and for ferrous solid rod of big diameter. At 310 g it is the heaviest blade here, which suits the bigger saws it fits.
4. Imachinist S64514. The 4×6 pick: M42 bi-metal, 64-1/2 x 1/2 x 0.025 with 14 TPI, for 4×6 bandsaws and saws taking that size. Stated for ferrous solid rod of small diameter and for cutting soft ferrous metal. At 160 g it sits between the Lenox 3.2 oz and the Morse 5.76 oz, and it is the straightforward choice if your saw takes this exact size.
FAQ for welders
Is bi-metal or carbide better for a beginner?
Bi-metal. It is more forgiving of the mistakes beginners make, and every listing here is bi-metal, which tells you what the market offers first. Carbide earns its place once you know your stock and your saw.
What TPI should I use for thin tube?
The S933414 listing states its 10/14 TPI variable pitch suits thin pipe and tube profiles. Finer pitches suit thinner stock; the variable-pitch blades here cover a broader range in one blade.
Can one blade cut both steel and aluminum?
The MK Morse listing states compatibility with aluminum, carbon steel and stainless steel on one blade. Bi-metal blades are the generalists; match the TPI to the thinnest stock you cut.
How do I know which length my saw takes?
Read your saw’s manual or the old blade: the listings here span 44-7/8 in for portable saws, 64-1/2 in for 4×6 saws and 93 in for 7 x 12 saws. Length and width must match; TPI is your choice.
Why do the spec tables disagree with the titles?
Three listings have spec-table tooth figures that contradict their titles: 6 TPI, 3/4 TPI and 3 teeth against 14, 10/14 and 14/18 TPI. Per this site’s rules the titles win; the tables look like data-entry errors.
Related: portable band saw vs horizontal band saw, deep cut vs compact band saw, cold saw vs band saw and portable band saw vs chop saw.




