Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Manual Knockout Punch Set Guide for Sheet Metal

A manual knockout punch set cuts clean conduit holes in sheet metal by hand, and this guide shows how the kits here differ on sizes, capacity and what comes in the box.

Manual Knockout Punch Set Guide for Sheet Metal
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Klein Tools 53732SEN Knockout Punch SetKlein Tools 53732SEN Knockout Punch Set9.6/10View on Amazon
  2. 2UTZIKO Manual Knockout Hole Punch Driver Kit 1/2UTZIKO Manual Knockout Hole Punch Driver Kit 1/29.6/10View on Amazon

A panel full of conduit holes calls for a punch, not a hole saw. When a box or enclosure needs a clean round hole for a conduit fitting, a manual knockout punch set shears it by hand once the pilot hole is drilled, without the ragged edge a hole saw leaves behind. This guide explains what a manual knockout punch set does, how the punch and die work together, and how to pick between the kits covered here.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Klein Tools 53732SEN Knockout Punch Set

Klein Tools 53732SEN Knockout Punch Set

KLEIN TOOLS9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A six-size manual knockout punch set with a ratcheting wrench, two draw studs and a stated 10 gauge mild steel capacity.

Pros

  • Six punch and die sizes from 1.3 cm to 5.1 cm in one kit
  • States a 10 gauge cutting capacity in mild steel
  • Ratcheting wrench and two draw studs in the box
  • Splits slugs for easy removal and punches clean holes

Cons

  • No warranty term is stated
  • At 6.7575 pounds it is a bench kit, not a pouch tool
  • Kit measures 12.0 by 10.0 by 3.0 inches, so it takes bench space
  • No stated cutting capacity for stainless steel
UTZIKO Manual Knockout Hole Punch Driver Kit 1/2

UTZIKO Manual Knockout Hole Punch Driver Kit 1/2

UTZIKO9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A manual knockout punch kit with punches and dies for conduit holes, a long handle and a toolbox for storage.

Pros

  • Punches and dies for conduit holes across the listed range
  • Long handle design for easy operation and less fatigue
  • Compact toolbox included for storage and portability
  • Punches mild steel, aluminum, fiberglass and plastic

Cons

  • No warranty term is stated
  • No stated cutting capacity in gauge, so capacity is harder to compare
  • Kit dimensions are not stated
  • No slug splitting feature is stated

What a manual knockout punch set does

A knockout punch is a matched punch and die that shear a hole through sheet metal. You drill a pilot hole, thread a draw stud through the punch, the metal and the die, then turn the stud with a wrench or handle so the punch draws through the metal and shears out a slug. The die supports the metal around the hole, which is why the edge comes out cleaner than a drilled or sawn hole.

Side by side

Klein Tools 53732SEN UTZIKO MK-60 Notes
Conduit sizes Six sizes, 1.3 to 5.1 cm Punches and dies for conduit holes Klein lists each size; UTZIKO lists the range
Cutting capacity 10 gauge mild steel Mild steel, aluminum, fiberglass, plastic Klein states a gauge; UTZIKO lists materials
In the box Six punches and dies, two draw studs, ratcheting wrench Punches and dies, long handle, toolbox Klein lists every piece; UTZIKO lists a toolbox
Slug removal Splits slugs for easy removal Not stated Klein states it; UTZIKO does not
Item weight 6.7575 pounds 8.42 pounds As listed

The Klein kit lists every size and a gauge capacity, while the UTZIKO kit lists the same kind of range in fewer words and adds a toolbox. Read the size list and the stated capacity before ordering, since neither kit states a warranty term.

The manual knockout punch set kits

Both kits punch conduit holes by hand, and the difference is in what the maker states: sizes, capacity and what comes in the box.

When a manual set is the right call

  • Panel and box work. Conduit entries in enclosures, panels and junction boxes where a clean round hole matters.
  • No power for the punch. The punch itself needs no outlet and no cord to drag across the shop.
  • Sheet metal and listed materials. Sheet metal, aluminum, fiberglass and plastic, the materials both makers list.
  • When to reach for a hole saw instead. Our hole saw vs knockout punch guide compares the two so you can pick the right tool for the hole.

For the cutting side of the job, see our best punch set for steel and best drift punch set roundups.

How to use a manual knockout punch

Mark the hole center, drill a pilot hole, then assemble the punch and die on either side of the metal with the draw stud through the pilot hole. Turn the stud with the wrench or handle until the punch shears through, then back the stud off and lift the slug out. Klein states its punches split slugs for easy removal.

Wear eye protection and gloves when handling punched sheet metal, and keep fingers clear of the punch and die while turning the stud. Clamp the work so the panel cannot shift.

FAQ for welders

What size knockout punch do I need for conduit?

Match the punch to the conduit fitting, not to the panel. The Klein kit lists six sizes from 1.3 cm to 5.1 cm, so check the fitting size first and pick the punch that matches it. A punch that is too large leaves a loose fitting, while a punch that is too small will not take the fitting at all.

Can a manual knockout punch cut mild steel?

Yes, within the capacity the maker states. Klein lists a cutting capacity of 10 gauge mild steel, and both kits list aluminum, fiberglass and plastic as well. For stock beyond the stated capacity, use a hydraulic knockout punch set instead.

What is the difference between a knockout punch and a hole saw?

A punch shears the hole with a matched punch and die, which leaves a cleaner edge. A hole saw cuts with teeth and leaves a rougher edge and more cleanup. Our hole saw vs knockout punch guide compares the two in detail.

Do I need a wrench with a knockout punch set?

The draw stud needs turning, and the Klein kit includes a 2.5 cm ratcheting wrench for that job. The UTZIKO kit uses a long handle instead, so check what comes in the box before ordering. Either way, the turning tool is part of the kit, not an extra to buy.

How do I remove the slug after punching?

Back the draw stud off and lift the slug out of the die. Klein states its punches split slugs for easy removal, which helps when the slug sticks in the die. Clear the slug before the next hole so it cannot score the panel.

Related: best metal knockout hole punch set, best tin snips for sheet metal, sheet metal shears vs tin snips, and the metal fab tools hub.

More buying guides

Metal Fab Tools ·

Best Metal Knockout Hole Punch Set (2026)

Five manual knockout punch sets compared for conduit and panel holes, with sizes, thickness limits, and kit contents from the listings.