Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Punch Set for Steel (2026): 5 Picks for the Shop

Five punch sets for steel work, compared by type, size range, steel, hardness, storage and the bench block and hammer each listing states.

Best Punch Set for Steel (2026): 5 Picks for the Shop
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1BESTNULE Pin Punch SetBest OverallBESTNULE Pin Punch Set9.7/10View on Amazon
  2. 2NEIKO Transfer Punch SetBest for MarkingNEIKO Transfer Punch Set9.6/10View on Amazon
  3. 3HORUSDY Pin Punch SetBest Simple SetHORUSDY Pin Punch Set9.6/10View on Amazon
  4. 4DkOvn Pin Punch SetBest Long ReachDkOvn Pin Punch Set9.5/10View on Amazon

A stuck roll pin can stall a repair fast. The pin sits flush, the hole is tight, and a nail or a screwdriver only mushrooms the end and marks the surface around it. The right punch drives the pin straight out and leaves the hole clean for the new pin. This guide covers the best punch set for steel, comparing pin and transfer punches for driving pins, marking hole centers and fitting parts on steel.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall BESTNULE Pin Punch Set: Widest size coverage plus a bench block and a hammer with 4 faces. Check price on Amazon
  • Best for Marking NEIKO Transfer Punch Set: 28 transfer punches from 3/32 to 1/2 inch with an index stand. Check price on Amazon
  • Best Simple Set HORUSDY Pin Punch Set: Full 1/16 to 5/16 inch range in a pouch, in hardened 40# steel. Check price on Amazon
  • Best Long Reach DkOvn Pin Punch Set: 8 in long punches reach deeply set pins in obstructed areas. Check price on Amazon

The machines

BESTNULE 25pc Punch Set and Hammer

BESTNULE 25pc Punch Set and Hammer

BESTNULE9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 25-piece pin punch set with a bench block, tweezers and a hammer with 4 replaceable faces, forged from heat-treated 40# chrome steel hardened to HRC 50-55.

Pros

  • Widest size coverage here, from roll pin to hollow end starter punches
  • Bench block with magnetic pin catcher and removal grooves
  • Hammer with brass, chrome steel, nylon and rubber faces
  • Forged 40# chrome steel hardened to HRC 50-55

Cons

  • No safety standard is stated for the set
  • No warranty term is stated in the listing
  • Plastic pin punches at 3/8 and 15/64 inch suit lighter work only
  • The full kit is heavier to carry than a pouch of punches alone
NEIKO 02621A Transfer Punch Set with Premium

NEIKO 02621A Transfer Punch Set with Premium

NEIKO9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 28-piece transfer punch set in heat-treated alloy steel with a black oxide finish, covering 3/32 to 1/2 inch for marking hole centers before drilling.

Pros

  • 28 punches from 3/32 to 1/2 inch in 1/64-inch increments
  • Suits toolmakers and machinists transferring hole positions
  • Precisely machined points for accurate hole marking
  • Index stand keeps every size visible and organized

Cons

  • No safety standard is stated for the set
  • No warranty term is stated in the listing
  • Transfer punches do not drive stuck pins out
  • No hammer or bench block is included in the kit
HORUSDY 8 Pieces Pin Punch Set

HORUSDY 8 Pieces Pin Punch Set

HORUSDY9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An 8-piece pin punch set in hardened, drop forged 40# steel with knurled handles and a fitted nylon storage pouch for removing and reusing roll pins.

Pros

  • Covers 1/16 through 5/16 inch in one set
  • Heat treated, drop forged and hardened 40# steel
  • Knurled handles for grip during hammer work
  • Fitted nylon pouch for carry, storage or hanging

Cons

  • No safety standard is stated for the set
  • No warranty term is stated in the listing
  • No hammer or bench block is included in the kit
IRWIN Punch Set, 6-Pack with Various Sizes

IRWIN Punch Set, 6-Pack with Various Sizes

IRWIN9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 6-pack punch set forged from tempered tool steel in one-piece construction, with a powder coating for visibility and six common pin punch sizes.

Pros

  • One-piece construction forged from tempered tool steel
  • Hardened and tempered steel for longer product life
  • Powder coating helps visibility for quick identification
  • Six common sizes from 1/16 to 5/16 inch

Cons

  • No safety standard is stated for the set
  • No warranty term is stated in the listing
  • No storage pouch or case is stated in the listing
  • No hammer or bench block is included in the kit
8 in Long 1/8" - 3/8" Carbon Steel Pin Punch Set

8 in Long 1/8" - 3/8" Carbon Steel Pin Punch Set

DkOvn9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-piece long-reach pin punch set, 8 in long with knurled handles in hardened steel, plus a black fitted nylon storage pouch for deeply set pins.

Pros

  • 8 in long reach for deeply set pins in obstructed areas
  • Knurled handles with a flower steel handle shape for grip
  • Hardened steel for durability and workability
  • Black fitted nylon pouch fits a toolbox or hangs on a wall

Cons

  • No safety standard is stated for the set
  • No warranty term is stated in the listing
  • Narrowest size range here, starting at 1/8 inch
  • No hammer or bench block is included in the kit

Other welders and gear to compare

Spec sheet comparison

Model Gear Score Type Pieces Size range Steel Storage Warranty
BESTNULE Pin Punch Set 9.7/10 Pin punch with bench block and hammer 25-piece set 1/16 to 5/16 inch, plus 3/8 inch plastic Heat-treated 40# chrome steel, HRC 50-55 Compact organizer box with bench block Not stated
NEIKO Transfer Punch Set 9.6/10 Transfer punch 28 Piece Set 3/32 to 1/2 inch Heat-treated alloy steel, black oxide Index stand Not stated
HORUSDY Pin Punch Set 9.6/10 Pin punch 8 Pieces 1/16 to 5/16 inch Hardened 40# steel, knurled Fitted nylon storage pouch Not stated
IRWIN Punch Set 9.5/10 Pin punch 6-Pack 1/16 to 5/16 inch Tempered tool steel Not stated Not stated
DkOvn Pin Punch Set 9.5/10 Pin punch, long reach 5pcs 1/8 to 3/8 inch Hardened steel, knurled handle Black fitted nylon storage pouch Not stated

Treat the specs as maker ratings pulled straight from the listings; we gathered them on 30 October 2026.

Buying guide: the best punch set for steel

Pin punches versus transfer punches

Pin punches drive pins out of holes, while transfer punches mark the center of an existing hole onto another surface for drilling. The NEIKO set here is a transfer punch set, with 28 steel punches from 3/32 to 1/2 inch in 1/64-inch increments. The other four sets are pin punches for removing and reusing roll pins and solid pins. Match the set type to the job: a transfer set will not drive a stuck pin, and a pin punch will not mark a hole center as cleanly.

Size range and count

Size range decides whether the set covers the pins on the bench. The BESTNULE set covers the widest ground, with roll pin punches, flat pin punches, hollow end starter punches, carbon steel punches from 1/8 to 5/16 inch, and plastic pin punches at 3/8 and 15/64 inch. The HORUSDY set covers 1/16, 3/32, 1/8, 5/32, 3/16, 7/32, 1/4 and 5/16 inch, while the IRWIN set covers 1/16, 5/32, 5/16, 1/4, 3/16 and 1/8 inch. The DkOvn set is narrower, with 1/8, 3/16, 1/4, 5/16 and 3/8 inch, but its long reach suits deeply set pins. Check the pin sizes on the job before choosing, since a missing size means a second order.

Steel and hardness

Hardened steel holds its tip shape under hammer blows, while soft steel mushrooms and bends. The BESTNULE punches are forged from heat-treated 40# chrome steel, hardened to HRC 50-55, with a chrome-plated or black oxide finish. The HORUSDY punches are heat treated, drop forged and hardened 40# steel with knurled handles. The NEIKO punches are heat-treated alloy steel with a black oxide finish, the DkOvn punches are hardened steel with knurled handles, and the IRWIN punches are forged from tempered tool steel in one-piece construction. Reinforced high-stress points, stated for the BESTNULE set, help a punch survive repeated impact without bending.

Handles, reach and storage

Knurled handles give grip when hands are oily, and long punches reach pins buried in housings. The DkOvn punches are 8 in long with knurled handles and a flower steel handle shape for gripping power, and the set comes with a black fitted nylon storage pouch. The HORUSDY set also comes with a fitted nylon storage pouch, while the NEIKO set stands in an easy-to-see index stand. The BESTNULE set packs into a compact organizer box with a bench block, tweezers and a hammer, so the whole kit travels as one case. Storage matters in a shop, since loose punches roll off benches and go missing.

Bench block and hammer

Only the BESTNULE set includes a bench block and a hammer. Its enhanced bench block has a removal groove, a staking groove, a drift channel, a link pin removal V channel, hammer and sear pin removal holes, a slide rail dressing round bottom channel and a magnetic built-in pin catcher. Its chrome-plated steel hammer weighs 8 oz and includes 4 replaceable faces in brass, chrome steel, nylon and rubber, so striking force can be matched to delicate or heavy work. The other sets assume a hammer is already on the bench, so drivers buying those sets should check the hammer drawer first.

Before You Strike an Arc

  • Setup: confirm the punch size against the pin before striking, since an oversize punch marks the hole and an undersize punch bends.
  • Fit check: the NEIKO index stand, the BESTNULE organizer box and the nylon pouches keep sizes sorted, so check the full set on arrival.
  • Power and consumables: these punch sets need no power supply, and the only consumable stated is the BESTNULE hammer with 4 replaceable faces.
  • Surface check: use the BESTNULE bench block or a stable, scratch-resistant surface under the work when driving pins out.
  • Eye protection: wear eye protection when striking steel punches, and keep bystanders clear of the work area.

FAQ for welders

What is the best punch set for steel pin removal?

For pin removal, a pin punch set like the BESTNULE, HORUSDY, DkOvn or IRWIN sets fits the job, while the NEIKO set is a transfer punch set for marking hole centers. The BESTNULE set covers the widest size range and adds a bench block and hammer, so it suits drivers who want one complete kit. Check the pin sizes on the job first, since range matters more than piece count alone.

Do pin punches work on steel pins?

Yes, when the punch steel is harder than the pin and the size matches the hole. The sets here state heat-treated, hardened or tempered steel, with the BESTNULE hardened to HRC 50-55. Strike straight along the pin axis, and stop if the punch starts to bend, since a bent punch can snap or mark the hole.

What sizes should a pin punch set cover?

Common pin work falls between 1/16 and 3/8 inch across these listings. The HORUSDY set covers 1/16 through 5/16 inch, the IRWIN set covers 1/16, 5/32, 5/16, 1/4, 3/16 and 1/8 inch, and the DkOvn set covers 1/8 through 3/8 inch. The BESTNULE set adds hollow end starter punches from 1/16 to 1/8 inch for starting stubborn pins without slipping.

What is a transfer punch set used for?

A transfer punch marks the center of an existing hole onto another surface so the drilled hole lands in the same place. The NEIKO set includes 28 steel punches from 3/32 to 1/2 inch in 1/64-inch increments, each with a precisely machined point, plus an index stand. It suits toolmakers and machinists transferring threaded, drilled or reamed hole positions.

Why does a bench block matter for pin work?

A bench block supports the work, protects the surface under it and gives grooves and holes for pins to exit into. The BESTNULE bench block adds a magnetic pin catcher, a removal groove, a staking groove and a drift channel. The other sets here state no bench block, so a flat, stable surface and a clear exit path for the pin matter even more.

Related: our metal fab tools hub.

Scoring, line by line

Each punch set is scored on performance, build, value, safety and warranty, with the weights published on our How We Pick page. No listing here states a safety standard or a warranty term, so every pick scores zero on those two criteria, and the ranking comes from performance, build and value.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
BESTNULE Pin Punch Set 9.7 32 21 22 n/a 0
NEIKO Transfer Punch Set 9.6 30 21 20 n/a 0
HORUSDY Pin Punch Set 9.6 28 20 20 n/a 0
IRWIN Punch Set 9.5 28 20 19 n/a 0
DkOvn Pin Punch Set 9.5 27 19 19 n/a 0

Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score. Where safety does not apply (unpowered gear with no listed safety features), it is left out and the remaining 90 points make up the score.

More buying guides

Metal Fab Tools ·

Best Roll Pin Punch Set (2026)

Five roll pin punch sets compared by size range, tip, steel, handles and storage for automotive, machinery and gunsmithing work.