Best Punch Set for Steel Under $30 (2026)
Four punch sets for steel work under 30, compared on sizes, length, steel type and warranty.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallCrescent CPCCHS12 Punch and Chisel Set9.7/10View on Amazon - 2
Best Pin Punch SetPerformance Tool W758 Pin Punch Set9.6/10View on Amazon - 3
Best Center Punch SetOuvlaiz 4-Piece Center Punch Set9.6/10View on Amazon - 4
Best for Soft MaterialsGeneral Tools 1280ST Hollow Punch Set9.5/10View on Amazon
A mark that wanders means a hole that wanders, and a pin that will not move means a long afternoon with a hammer and a punch that bends instead of driving. The work starts with a clean center mark, a punch that fits the pin, and a striking face that stays true. This guide covers the best punch set for steel under 30, with sets compared on punch sizes, length, steel type and warranty.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall Crescent CPCCHS12 Punch and Chisel Set: 12 pieces of forged and heat treated steel, a striking cap that resists mushrooming, and a lifetime limited warranty. Check price on Amazon
- Best Pin Punch Set Performance Tool W758 Pin Punch Set: Five pin punches from 1/8 to 3/8 inch, 8 inches long to reach deeply set pins, with knurled steel handles. Check price on Amazon
- Best Center Punch Set Ouvlaiz 4-Piece Center Punch Set: Four hardened steel center punches from 1/32 to 4/32 inch with a knurled handle and black oxide finish. Check price on Amazon
- Best for Soft Materials General Tools 1280ST Hollow Punch Set: Six hollow punches from 3/16 to 1/2 inch with a side clearance hole, for leather, rubber and gasket material. Check price on Amazon
The machines

Crescent 12 Piece Set, Punch & Chisel - CPCCHS12
A 12-piece punch and chisel set in forged and heat treated steel, with a striking cap design and a lifetime limited warranty.
Pros
- 12 pieces cover punch and chisel work in one set
- Forged and heat treated steel, stated for durability and long tool life
- Striking cap design reduces mushrooming and keeps hands away from contact
- High-viz coloring and bold size markings for quick identification on the job
Cons
- No punch sizes are stated in the listing
- Length is described as extended with no figure stated
- No case or pouch is stated
- Set mixes chisels with punches, so not every piece suits punch work

Performance Tool W758 5-Piece 8 in. Long Pin Punch
A 5-piece pin punch set, 8 inches long, in carbon steel with hardened tips and knurled handles for driving deeply set pins.
Pros
- 8 inches long to reach deeply set pins in obstructed areas
- Five pin sizes from 1/8 to 3/8 inch
- Hardened tips on carbon steel construction
- Knurled steel handles for sure grip
Cons
- No case or pouch is stated
- Warranty is stated as a manufacturer warranty with no term given
- Pin punches only, with no center punch for marking
- The 8 inch length suits deep pins and can feel long for close bench work

Ouvlaiz 4-Piece Center Punch Set with Sizes
A 4-piece center punch set in hardened steel, with sizes from 1/32 to 4/32 inch, a knurled handle and a black oxide finish.
Pros
- Four sizes from 1/32 to 4/32 inch for fine marking work
- Hardened steel, stated to resist deformation, chipping and wear
- Knurled handle and 3.78 inch length for control
- Black oxide finish resists corrosion, and each punch is stamped with its size
Cons
- Largest size is 4/32 inch, so no punch for larger marks
- Center punches only, with no pin punch for driving pins
- No warranty is stated
- No case or pouch is stated

General Tools Hollow Steel Punch Set #1280ST
A 6-piece hollow punch set from 3/16 to 1/2 inch in heat treated forged steel, made for cutting holes in leather, rubber, gasket material, cardboard and softer metals.
Pros
- Six hole sizes from 3/16 to 1/2 inch
- Side clearance hole for easy removal of punched material
- Heat treated forged steel, stated for a cutting edge that stays sharper for longer
- Ships in a plastic roll pouch
Cons
- Made for leather, rubber, gasket material, cardboard and softer metals, not steel
- No punch length is stated
- No warranty is stated
- Hollow punches cut holes only, with no center punch for marking and no pin punch for driving pins
Other welders and gear to compare
HORUSDY 12-Piece Punch and Chisel SetCheck price on Amazon
HORUSDY 28-Piece Heavy Duty Punch and Chisel SetCheck price on Amazon
OWDEN 36Pcs Steel Metal Stamps SetCheck price on Amazon
9-Piece Roll Pin Punch SetCheck price on Amazon
OWDEN Professional 36Pcs Steel Metal Stamps SetCheck price on Amazon
NEIKO 02629A Number and Letter Punch Set with Heat-TreatedCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Pieces | Sizes | Length | Material | Warranty |
|---|---|---|---|---|---|---|
| Crescent CPCCHS12 Punch and Chisel Set | 9.7/10 | 12 | Not stated | Not stated | Forged and heat treated steel | Lifetime Limited |
| Performance Tool W758 Pin Punch Set | 9.6/10 | 5 | 1/8 to 3/8 in | 8 in | Carbon steel, hardened tips | Not stated |
| Ouvlaiz 4-Piece Center Punch Set | 9.6/10 | 4 | 1/32 to 4/32 in | 3.78 in | Hardened steel | Not stated |
| General Tools 1280ST Hollow Punch Set | 9.5/10 | 6 | 3/16 to 1/2 in | Not stated | Heat treated forged steel | Not stated |
Ratings in this table are the makers’ own claims taken from each product page (20 November 2026). Where a listing states a figure two ways, the table shows both.
How the picks were scored
Each punch set is scored on performance, build, value, safety listing and warranty, with the weights published on the How We Pick page. A spec the listing does not publish scores nothing.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Crescent CPCCHS12 Punch and Chisel Set | 9.7 | 30 | 22 | 21 | n/a | 4 |
| Performance Tool W758 Pin Punch Set | 9.6 | 29 | 20 | 21 | n/a | 0 |
| Ouvlaiz 4-Piece Center Punch Set | 9.6 | 28 | 20 | 20 | n/a | 0 |
| General Tools 1280ST Hollow Punch Set | 9.5 | 24 | 20 | 19 | n/a | 0 |
The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure. Safety points apply to gear that runs on power or lists safety features. Without either, we score out of 90 instead of 100.
Buying guide: what matters in the best punch set for steel under 30
Center punch, pin punch or hollow punch
These three punch types do different jobs, and the sets here split across them. A center punch marks the spot before drilling, and the Ouvlaiz set holds four of them from 1/32 to 4/32 inch. A pin punch drives pins out, and the Performance Tool set holds five of them from 1/8 to 3/8 inch, 8 inches long to reach deeply set pins in obstructed areas. A hollow punch cuts holes, and the General Tools set cuts them in leather, rubber, gasket material, cardboard and softer metals, with a side clearance hole for removing punched material. The Crescent set pairs punches with chisels, so it covers marking, driving and cutting work in one box.
Sizes and length
Match the punch to the pin or the hole. The Ouvlaiz center punches run from 1/32 to 4/32 inch and measure 3.78 inches long with a 0.32 inch diameter. The Performance Tool pin punches run from 1/8 to 3/8 inch at 8 inches long, which suits pins buried behind brackets and housings. The General Tools hollow punches run from 3/16 to 1/2 inch. The Crescent set states no punch sizes and no punch length, only that the length is extended to keep the holding hand away from obstructions and debris, so check the sizes before ordering if a specific pin is in mind.
Steel type and hardness
All four sets state a steel body, and the wording differs in ways that matter. Crescent and General Tools state forged and heat treated steel, with General Tools adding that the heat treatment keeps the cutting edge sharper for longer. Ouvlaiz states hardened steel, and adds a black oxide finish that prevents corrosion. Performance Tool states carbon steel construction with hardened tips, and knurled steel handles for a sure grip. A hardened tip holds its shape under the hammer, and a knurled handle keeps the punch from turning in the hand.
What ships in the box
Count the pieces against the jobs on the bench. Crescent ships 12 pieces, Performance Tool ships 5, Ouvlaiz ships 4 and General Tools ships 6. Only the General Tools set states storage, a plastic roll pouch that holds the six punches. The other listings state no case or pouch, so plan a drawer or roll of your own for keeping sizes together. None of the listings state a hammer, so the hammer comes from the bench.
Warranty in writing
Only one set here states a warranty term. Crescent states a lifetime limited warranty, which backs the 12-piece set for the long run. Performance Tool states a manufacturer warranty with no term given. Ouvlaiz and General Tools state no warranty at all. A warranty term in writing is worth more than a bare promise, so weigh the Crescent term against the sizes each set actually covers.
Before You Strike an Arc
- Wear eye protection before striking any punch or chisel: a chip can leave the striking face without warning.
- Clamp the work so it cannot shift while marking a center or driving a pin.
- Check each punch on arrival: the tip should be true and the striking cap free of mushrooming.
- Match the punch to the job: a center punch marks, a pin punch drives, and a hollow punch cuts holes in soft material.
- Strike square on the cap and keep the holding hand clear of the striking end.
FAQ for welders
What size punch set do I need for steel?
It depends on the job, not the drawer. For marking, the Ouvlaiz center punches run from 1/32 to 4/32 inch, which covers fine layout marks. For driving pins, the Performance Tool pin punches run from 1/8 to 3/8 inch. For cutting holes, the General Tools hollow punches run from 3/16 to 1/2 inch, but only in leather, rubber, gasket material, cardboard and softer metals.
Can a hollow punch set cut steel?
Not the set in this guide. The General Tools listing states leather, rubber, gasket material, cardboard and softer metals, and steel is not in that list. For steel, mark the spot with a center punch and drill the hole. A hollow punch earns its keep on gaskets and soft material, not on plate.
What is the difference between a center punch and a pin punch?
A center punch makes a mark for the drill, and a pin punch drives a pin out of a hole. The Ouvlaiz set holds center punches from 1/32 to 4/32 inch, each stamped with its size. The Performance Tool set holds pin punches from 1/8 to 3/8 inch, 8 inches long, with hardened tips for driving deeply set pins.
How long should a pin punch be?
Long enough to reach the pin and still leave room to strike it square. The Performance Tool set is 8 inches long to reach deeply set pins in obstructed areas. The Crescent set states an extended length to keep the holding hand away from obstructions and debris. Short punches suit open bench work, and long punches suit buried pins.
Do punch sets under $30 come with a warranty?
Sometimes, and the term matters more than the word. Crescent states a lifetime limited warranty on its 12-piece set. Performance Tool states a manufacturer warranty with no term given. Ouvlaiz and General Tools state no warranty at all, so read the listing before ordering if a warranty term matters to the purchase.
Related: how to use a pin punch for driving pins out safely, how to use center punch on metal, and the metal fab tools hub. Also see our best drift punch set. Also see our best center punch for metal. Also see our best roll pin punch set. Also see our best automatic center punch. Also see our best cold chisel set.




