Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Use a Pin Punch: Driving Pins Out Safely

A pin punch drives a pin out of its hole, and this guide shows how to pick the right size, support the work and strike the punch square.

How to Use a Pin Punch: Driving Pins Out Safely
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1BESTNULE 26pc Roll Pin Punch Set with Bench BlockBESTNULE 26pc Roll Pin Punch Set with Bench Block9.6/10View on Amazon
  2. 2Amazon Basics 16-Piece Chrome Vanadium Steel PunchAmazon Basics 16-Piece Chrome Vanadium Steel Punch9.6/10View on Amazon
  3. 3HORUSDY 16-Piece Punch and Chisel SetHORUSDY 16-Piece Punch and Chisel Set9.6/10View on Amazon

A pin sits flush in a joint and will not move with fingers alone, and a hammer on the pin itself would mushroom the end. A pin punch drives the pin out of its hole, with the punch sized to the pin and the work held steady. This guide shows how to use a pin punch to drive pins out of a joint, step by step.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

BESTNULE 26pc Roll Pin Punch Set with Bench Block

BESTNULE 26pc Roll Pin Punch Set with Bench Block

BESTNULE9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 26-piece roll pin punch set with a bench block, a pivot pin tool and a hammer with 4 replaceable faces, covering steel punch sizes from 1/16 in to 5/16 in.

Pros

  • 26 pieces covering roll pin, flat pin and hollow end starter punches
  • Bench block with a magnetic pin catcher and removal grooves
  • Hammer with 4 replaceable faces: brass, chrome steel, nylon and rubber
  • Heat-treated 40# chrome steel, hardened to HRC 50-55

Cons

  • No warranty term is stated
  • Roll pin punches come in 1/16 in and 3/32 in only
  • Punch lengths run 2.76 in to 3.58 in, so longer punches are not in the set
  • 26 small pieces to keep track of in the organizer box
Amazon Basics 16-Piece Chrome Vanadium Steel Punch

Amazon Basics 16-Piece Chrome Vanadium Steel Punch

Amazon Basics9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 16-piece punch and chisel set with 5 pin punches, 5 taper punches, 3 cold chisels, 2 center punches and a chisel punch gauge, in heat treated chrome vanadium steel.

Pros

  • 16 pieces: 5 pin punches, 5 taper punches, 3 cold chisels and 2 center punches
  • Heat treated chrome vanadium alloy steel construction
  • Comfortable handles that reduce hand strain and improve accuracy
  • Storage pouch with velcro closure keeps the tools organized

Cons

  • No warranty term is stated
  • No bench block or hammer in the set
  • Solid pin punches, so roll pins call for a roll pin punch set
  • 1 chisel punch gauge for the whole set
HORUSDY 16-Piece Punch and Chisel Set

HORUSDY 16-Piece Punch and Chisel Set

HORUSDY9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 16-piece punch and chisel set in heat treated chrome vanadium steel, hardened to 54~58 HRC, with taper, pin and center punches and cold chisels.

Pros

  • 16 pieces: 5 taper punches, 3 cold chisels, 5 pin punches and 2 center punches
  • Heat treated chrome vanadium steel, hardness 54~58 HRC
  • Pin punch sizes from 3/32 in to 1/4 in, in lengths to 5-3/4 in
  • Taper punches and cold chisels in the same set

Cons

  • No bench block or hammer in the set
  • No pouch or case is stated for the set
  • Cold chisels run 3/8 in to 5/8 in, so wider chisels are not in the set
  • Pin punches run 3/32 in to 1/4 in, so larger pins need a larger punch

How to Use a Pin Punch in Order

Start with the pin and the hole it sits in. Pick a punch that matches the pin: a pin punch that fits the pin drives it straight, and a punch that is too small can slip off the pin. Support the work on a bench block or a solid surface so the pin has somewhere to go, and set the punch on the pin before the hammer moves.

Hold the punch straight and strike the end square with the hammer. Short, firm strikes move the pin better than wild swings, and the punch stays on the pin between strikes. If the pin stops moving, stop and check the fit: a punch that is too large can jam in the hole, and a pin that is bent can bind in the bore.

The BESTNULE set holds the most pieces at 26, with roll pin punches, flat pin punches and hollow end starter punches, plus a bench block and a hammer with 4 replaceable faces. The Amazon Basics set gives 5 pin punches, and the HORUSDY set gives 5 pin punches, with taper punches, cold chisels and center punches in the same set. Match the punch to the pin, and let the bench block take the force.

Pick the Right Punch for the Pin

Pin punches come in sizes, and the size on the punch should match the pin. The BESTNULE steel punches (on Amazon) run from 1/16 in to 5/16 in, and the HORUSDY pin punches run from 3/32 in to 1/4 in. The Amazon Basics set gives 5 pin punches, so check the size on the punch before use. A starter punch opens a stuck pin, and a flat pin punch follows it through.

The bench block and the hammer matter as much as the punch. The BESTNULE bench block holds the work on a stable surface, with a removal groove, a staking groove and a magnetic pin catcher that keeps the pin from rolling away. The hammer has 4 replaceable faces, so brass, chrome steel, nylon and rubber cover heavy striking and delicate assembly. A punch that fits the pin and a hammer that fits the hand do the work together.

Side by Side

BESTNULE 26-Piece Amazon Basics 16-Piece HORUSDY 16-Piece
Pieces 26 16 16
Pin punch sizes 1/16 in and 3/32 in roll pin Not stated 3/32 in to 1/4 in
Cold chisels Not stated 3 cold chisels 3 cold chisels, 3/8 in to 5/8 in
Steel Heat-treated 40# chrome steel, HRC 50-55 Heat treated chrome vanadium alloy steel Heat treated chromium vanadium steel, 54~58 HRC
Hammer 8 oz, 4 replaceable faces Not stated Not stated
Bench block Included, with magnetic pin catcher Not stated Not stated
Storage Compact organizer box Storage pouch with velcro closure Not stated
Item weight Not stated 2.6 lb Not stated
Warranty Not stated Not stated Not stated

The table shows the trade: the BESTNULE set brings the bench block, the hammer and the roll pin sizes, and the 16-piece sets bring cold chisels and taper punches alongside the pin punches. Pick the set that holds the punches the job calls for.

The Gear for This Job

The punch drives the pin, the bench block holds the work, and the hammer does the striking, so here are the 3 sets for the job.

If the set is still to buy, the roll pin punch roundup and the punch set roundup show sets for the shop.

Checks Before the First Strike

With the punch picked, look the pin over before the hammer moves. Check that the punch tip fits the pin and that the work sits flat on the bench block or a solid surface, with room for the pin to come out. Wear safety goggles, and keep hands clear of the punch tip.

Strike square and check the punch tip after the pin moves: a tip that spreads or cracks has done its work and needs replacing. Keep the punches in the pouch or the organizer box, and wipe the bench block clean so the next pin sits flat.

After the Pin Comes Out

Once the pin is out, set it down where it will not roll away. The BESTNULE bench block has a magnetic pin catcher for the pin, and the organizer box holds the punches in place. Wipe the punch tips clean and check them for spread or cracks before the next job.

FAQ for welders

What size pin punch do I need?

Match the punch to the pin. The BESTNULE steel punches run from 1/16 in to 5/16 in, and the HORUSDY pin punches run from 3/32 in to 1/4 in. Check the size on the punch before use, and use a starter punch on a stuck pin.

Can I use a pin punch on a roll pin?

Use a roll pin punch for roll pins. The BESTNULE set holds roll pin punches in 1/16 in and 3/32 in, plus flat pin punches in the same sizes. A solid pin punch can slip on a roll pin, so reach for the roll pin punch first.

Do I need a bench block to use a pin punch?

A bench block helps, and the BESTNULE set includes a bench block with a magnetic pin catcher and removal grooves. Support the work on a solid surface with room for the pin to come out, and a flat, steady rest keeps the punch square.

How do I keep a pin punch from slipping?

Pick a punch that matches the pin and hold it straight. Set the punch on the pin before the hammer moves, and strike the end square. If the punch slips, stop and check the fit before striking again.

Related: how to use a pin punch, best roll pin punch set, best punch set for steel, what is a roll pin punch, how to use a center punch and best cold chisel set.

More buying guides

Metal Fab Tools ·

Best Roll Pin Punch Set (2026)

Five roll pin punch sets compared by size range, tip, steel, handles and storage for automotive, machinery and gunsmithing work.