Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Use Center Punch on Metal

How to use a center punch to mark an exact starting spot for drilling, with the steps and the 4 punch sets that cover the job.

How to Use Center Punch on Metal
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 125-Piece Punch and Chisel Set with Roll Pin25-Piece Punch and Chisel Set with Roll Pin9.7/10View on Amazon
  2. 2TEKTON Center Punch Set, 5-Piece | PNC95002TEKTON Center Punch Set, 5-Piece | PNC950029.7/10View on Amazon
  3. 319-Piece Punch and Chisel Set, Pin Punches19-Piece Punch and Chisel Set, Pin Punches9.6/10View on Amazon
  4. 4WORKPRO 4-Piece Nail Punch and Center Punch SetWORKPRO 4-Piece Nail Punch and Center Punch Set9.6/10View on Amazon

Learning how to use center punch tools starts with the mark: set the sharp point on the spot, hold the punch upright, and strike the end with a hammer so the point leaves a dimple the drill bit can sit in. That dimple is the whole job: without it, the bit wanders across the metal. This guide covers the steps and the sets.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

25-Piece Punch and Chisel Set with Roll Pin

25-Piece Punch and Chisel Set with Roll Pin

SEDY9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 25-piece punch and chisel set with roll pin punches and cold chisels, in heat-treated chrome vanadium steel with a 1 year manufacturer warranty.

Pros

  • 25 pieces, the largest set here: 9 roll pin punches and 16 more pieces
  • Heat-treated chrome vanadium steel with black oxide finish
  • Tapered, pin, center and cold chisels for marking and pin removal
  • Fitted nylon storage pouch with pockets labeled by size

Cons

  • Center punch sizes are not stated
  • Color field reads 25-piece Set With Roll Pin Punches, not a color
  • 1 year warranty is the only stated term here
  • No weight stated in the listing
TEKTON Center Punch Set, 5-Piece | PNC95002

TEKTON Center Punch Set, 5-Piece | PNC95002

TEKTON9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 5-piece set of center punches from 1/4 to 1/2 in, machined from 5160 high carbon steel.

Pros

  • 5 center punches: 1/4, 5/16, 3/8, 7/16, 1/2 in
  • 5160 high carbon steel, individually heat treated
  • Sharp point machined to mark an exact starting spot for drilling
  • Sizes marked with high-visibility laser marking

Cons

  • Center punches only, no pin punches or chisels
  • No storage pouch stated in the listing
  • 5 pieces, fewer than the 19- and 25-piece sets
  • No nail setters for driving nails flush
19-Piece Punch and Chisel Set, Pin Punches

19-Piece Punch and Chisel Set, Pin Punches

HORUSDY9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 19-piece punch and chisel set with prick, center, pin and nail punches plus alignment tools and cold chisels, in heat-treated CR-V steel, in a rolling pouch.

Pros

  • 19 pieces: prick, center, pin and nail punches, alignment tools and chisels
  • Heat-treated CR-V steel for toughness and wear resistance
  • Rolling pouch with individual pockets and size markings
  • 2 center punches: 3/8 x 4-1/2 in and 1/8 in

Cons

  • No warranty term is stated
  • The second center punch lists only 1/8 in, with no length
  • No weight stated in the listing
  • No overall set dimensions stated in the spec table
WORKPRO 4-Piece Nail Punch and Center Punch Set

WORKPRO 4-Piece Nail Punch and Center Punch Set

WORKPRO9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 4-piece set with 1/32, 1/16 and 3/32 in nail setters and a 1/32 in center punch, in hardened Cr-V steel with a black oxide finish and knurled grips.

Pros

  • 1/32 in center punch for fine, exact marks
  • 3 nail setters: 1/32, 1/16 and 3/32 in
  • Hardened Cr-V steel with black oxide finish
  • Knurled grips to prevent slipping

Cons

  • No warranty term is stated
  • Only 4 pieces, the smallest set here
  • No storage pouch stated in the listing
  • Center punch is 1/32 in only

How to Use Center Punch

Start with a clear mark on the metal. Set the point of the punch on the mark and hold the punch upright, with the point where the hole should start. Strike the end with a hammer, once and square, so the point drives a dimple into the metal. Lift the punch and check the dimple: if it sits on the mark, drill. If it is off the mark, set the punch again and strike once more.

The punches side by side

Spec TEKTON 5-Piece Center Punch SEDY 25-Piece Punch Set HORUSDY 19-Piece Punch Set WORKPRO 4-Piece Punch Set
Pieces 5 center punches 25 19 4
Center punch sizes 1/4, 5/16, 3/8, 7/16, 1/2 in Sizes not stated 2: 3/8 x 4-1/2 in, 1/8 in 1/32 in
Steel 5160 high carbon steel Heat-treated chrome vanadium steel Heat-treated CR-V steel Cr-V steel
Finish Dry, rust-preventative coating Black oxide Not stated Black oxide
Storage Not stated Fitted nylon storage pouch Rolling pouch with individual pockets Not stated
Warranty No time limits, no receipts 1 Year Manufacturer Not stated Not stated

The TEKTON set lists 5 sizes, the WORKPRO set lists a single 1/32 in center punch, and the SEDY set does not state its center punch sizes at all.

Picking the right punch for the job

Match the punch to the mark. The TEKTON set lists the most center punch sizes, 5, from 1/4 to 1/2 in, so it suits a metalworker who marks holes across that range. The WORKPRO set suits fine work: its center punch is 1/32 in, and its nail setters run 1/32, 1/16 and 3/32 in for trim and furniture. The HORUSDY and SEDY sets suit a shop that wants more than marking: pin punches and cold chisels, plus alignment tools in the HORUSDY set. Our best punch set for steel roundup compares more sets.

The gear

The punch sets below cover the marking step.

Eye protection and clamping. A punch struck with a hammer can throw a chip, so wear eye protection and clamp the work before you strike.

FAQ for welders

What is a center punch used for?

A center punch marks an exact starting spot for drilling on the workpiece. The sharp point leaves a dimple that keeps the drill bit from wandering. The TEKTON listing describes the point as machined to precise tolerances.

What size center punch should I use?

Match the punch to the mark you need. The TEKTON set runs 1/4, 5/16, 3/8, 7/16 and 1/2 in, while the WORKPRO center punch (on Amazon) is 1/32 in for fine marks. The SEDY set does not state its center punch sizes, so ask the seller if the size matters.

Can I use a center punch on wood?

Yes. The HORUSDY, SEDY and WORKPRO listings all list woodworking among the uses, along with metalworking.

Do I need a hammer to use a center punch?

Yes. The listings describe the punch as struck with a hammer, and the SEDY listing calls out control and comfort under hammer impact. See our dead blow hammer uses guide.

What is the difference between a center punch and a prick punch?

The HORUSDY set includes 1 prick punch and 2 center punches. A prick punch makes a light mark for layout, while a center punch makes a deeper dimple that a drill bit can sit in. The set gives you both, so you can lay out with the prick punch and mark the spot with the center punch.

Related: transfer punch vs center punch, best punch set for steel, best drift punch set, best twist drill bit set, and the metal fab tools hub.

More buying guides

Metal Fab Tools ·

Best Automatic Center Punch (2026)

Automatic center punches for the home shop, compared on length, diameter, body, stroke control and warranty, from what each listing states.