Best Cold Chisel Set (2026): 5 Sets Compared
Five cold chisel sets compared on sizes, steel, hardness and warranty, from 3-piece Cr-V sets to a 5-piece alloy set.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallCrescent 3-Piece9.7/10View on Amazon - 2
Best 5-PieceMayhew 5-Piece9.7/10View on Amazon - 3
Best SteelTEKTON 3-Piece9.6/10View on Amazon - 4
Best HardnessValueMax 3-Piece9.6/10View on Amazon - 5
Budget PickHORUSDY 3-Piece9.5/10View on Amazon
A rusted bolt that will not turn, a rivet head that has to come off, a weld bead that needs trimming: that is cold chisel work. The chisel takes the hammer blow and the edge does the cutting, so the steel, the hardness and the striking end all matter. We compared five of the best cold chisel sets on what each listing states: chisel sizes, steel, hardness, count and warranty.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall Crescent 3-Piece: Striking cap, high-viz markings and a lifetime limited warranty Check price on Amazon
- Best 5-Piece Mayhew 5-Piece: Five chisels from 1/4 to 3/4 in, alloy steel, USA made Check price on Amazon
- Best Steel TEKTON 3-Piece: 5160 steel, USA made, no time limits on warranty Check price on Amazon
- Best Hardness ValueMax 3-Piece: 58 to 60HRC edge on 3/8, 1/2 and 5/8 in chisels Check price on Amazon
- Budget Pick HORUSDY 3-Piece: 3/8, 1/2 and 5/8 in Cr-V chisels at 54 to 58HRC Check price on Amazon
The machines

Crescent 3 Piece Set, 3/8", 1/2", 5/8" Chisel
A 3-piece set of 3/8, 1/2 and 5/8-inch chisels with a striking cap, high-visibility markings and a lifetime limited warranty.
Pros
- Striking cap reduces mushrooming
- High-visibility coloring and size markings
- Forged and heat treated steel
- Lifetime limited warranty stated
Cons
- No hardness figure stated
- 3-piece only, no 1/4 or 3/4 in
- No per-chisel lengths stated
- Bevel edge only, per the spec table

Mayhew Tools 90002 Cold Chisel Set, 5-Piece
A 5-piece set of alloy steel chisels from 1/4 to 3/4 inch with full shank heat treating, made in the USA.
Pros
- Five chisels, 1/4 to 3/4 in
- Tempered alloy steel, full shank heat treat
- Hex body resists rolling
- Made in the USA
Cons
- No hardness figure stated
- Call vendor is not a warranty term
- 16 oz total is light across 5 chisels
- No striking cap stated

TEKTON Cold Chisel Set, 3-Piece | PNC91002 1/2
A 3-piece set of 5160 high carbon steel chisels, individually heat treated, made in the USA.
Pros
- 5160 high carbon steel
- Individually heat treated
- Made in the USA
- No time limits on warranty
Cons
- No hardness figure stated
- 5.92 oz is the lightest stated weight

ValueMax 3-Piece Heavy-Duty Cold Chisel Set
A 3-piece set of 3/8, 1/2 and 5/8-inch Cr-V chisels with a 58 to 60HRC edge and drop-forged construction.
Pros
- 58 to 60HRC edge stated
- Drop-forged chromium vanadium steel
- Stated lengths per chisel
- Tail annealing for toughness
Cons
- No warranty stated
- No striking cap stated
- Plastic in the handle line
- 3-piece only, no 1/4 or 3/4 in

HORUSDY 3-Piece Heavy-Duty Cold Chisel Set, 3/8"
A 3-piece set of 3/8, 1/2 and 5/8-inch Cr-V chisels at 54 to 58HRC for cutting, shaping and forming.
Pros
- 54 to 58HRC hardness stated
- Chromium vanadium steel
- 3/8, 1/2 and 5/8 in sizes
- Names wood, metal and masonry uses
Cons
- No warranty stated
- No striking cap stated
- Plastic in the handle line
- Lowest stated hardness here
Other welders and gear to compare
HORUSDY 28-Piece Heavy Duty Punch and Chisel SetCheck price on Amazon
TEKTON Cold Chisel SetCheck price on Amazon
HORUSDY 3-Pieces Heavy Duty Cold Chisels SetCheck price on Amazon
IRWIN Chisel SetCheck price on Amazon
16PC Heavy Duty Punch Chisel SetCheck price on Amazon
Spec sheet comparison
| Chisel set | Gear Score | Sizes | Steel | Hardness | Warranty |
|---|---|---|---|---|---|
| Crescent 3-Piece | 9.7/10 | 3/8, 1/2, 5/8 in | Forged steel | Not stated | Lifetime Limited |
| TEKTON 3-Piece | 9.6/10 | Title: 1/2, 3/4, 1 in; bullets: 1/4, 3/8, 1/2 in | 5160 high carbon | Not stated | No time limits |
| Mayhew 5-Piece | 9.7/10 | 1/4 to 3/4 in, 5 pc | Alloy steel | Not stated | Not stated |
| ValueMax 3-Piece | 9.6/10 | 3/8, 1/2, 5/8 in | Cr-V | 58-60HRC edge | Not stated |
| HORUSDY 3-Piece | 9.5/10 | 3/8, 1/2, 5/8 in | Cr-V | 54-58HRC | Not stated |
Treat the specs as maker ratings pulled straight from the listings; we gathered them on 22 October 2026.
Buying guide: the best cold chisel set for the shop
Sizes in the set
Three of the five cover the same ground: the HORUSDY, ValueMax and Crescent sets each list 3/8, 1/2 and 5/8-inch chisels. The ValueMax adds lengths: 3/8 by 5-1/2, 1/2 by 5-7/8 and 5/8 by 6-3/4 inches. The Mayhew is the only 5-piece set, with 1/4, 3/8, 1/2, 5/8 and 3/4-inch chisels per its included-components line. The TEKTON is the odd one: its title says 1/2, 3/4 and 1 inch while its bullets say 1/4, 3/8 and 1/2 inch, so confirm the sizes on the listing before ordering.
Match the set to the work on the bench. The 3/8 to 5/8-inch range covers rivets, bolts and slag removal, which every listing names. The Mayhew’s 1/4-inch chisel suits finer work and its 3/4-inch chisel suits heavier cutting. A three-chisel set is enough for occasional use; the five-piece set covers the full range without a second order. For layout work before the chisel comes out, see our center punch for metal picks.
Steel and hardness
The listings name three steels. The HORUSDY and ValueMax are chromium vanadium steel, drop-forged on the ValueMax. The TEKTON is 5160 high carbon steel, individually heat treated. The Mayhew is tempered alloy steel with full shank heat treating, and the Crescent is forged and heat treated steel. Hardness is stated on two: the HORUSDY lists 54 to 58HRC and the ValueMax lists a 58 to 60HRC edge with tail annealing for toughness.
The listings present hardness as the edge’s resistance to dulling, and neither defines the scale beyond the numbers. A harder edge holds longer on steel and cast iron but can chip if struck wrong; the ValueMax pairs its harder edge with a toughened tail. For striking, the temper of the head matters as much as the edge: the TEKTON keeps a soft temper on the striking end while hardening the tip, which is the combination that resists mushrooming.
Striking ends and handling
The Crescent is the only set with a striking cap design, which the listing says reduces mushrooming and keeps the holding hand away from contact. Its extended length keeps the hand clear of obstructions and debris, and the recessed stock gives better control. High-visibility coloring and bold size markings identify each chisel on the bench. The other four list no striking cap; the HORUSDY and ValueMax list plastic in the handle material line, while the Mayhew lists a hex body that resists rolling.
Warranties
One listing states a warranty with a real term: the Crescent lists a lifetime limited warranty. The TEKTON lists no time limits and no receipts, which has no concrete term, so it scores no warranty points. The Mayhew says to call the vendor for warranty, which is not a stated term, and the HORUSDY and ValueMax listings state no warranty at all. A stated warranty matters on a striking tool, since the head takes the abuse; the Crescent is the documented pick on that count. For punch sets with similar warranty questions, see our transfer punch set picks.
Count and value
Count is the simplest value lever. The Mayhew is the only 5-piece set, adding 1/4 and 3/4-inch chisels to the 3/8, 1/2 and 5/8-inch core the other three share. The HORUSDY, ValueMax and Crescent sets each cover that core trio. The TEKTON sizes need confirmation on the listing before counting it. A 3-piece set suits a toolbox that already holds punches and drifts; the 5-piece set is the one-box answer for a new bench. Weights are stated on two: the Mayhew lists 16 ounces for five chisels and the TEKTON lists 5.92 ounces, both in their spec tables.
Before You Strike an Arc
- Wear eye protection: chisel work throws chips, and the listings name cutting steel, cast iron and masonry.
- Check the chisel sizes on the listing before ordering; the TEKTON title and bullets disagree on sizes.
- Inspect the striking end before each use; a mushroomed head should be dressed or the chisel replaced.
- Match the chisel to the material the listing names: rivets, bolts, slag, steel, brass, bronze, cast iron and aluminum.
- Keep the holding hand clear of the strike zone; the Crescent’s extended length and striking cap are built for this.
FAQ for welders
What sizes come in these sets?
The HORUSDY, ValueMax and Crescent sets each list 3/8, 1/2 and 5/8-inch chisels. The Mayhew 5-piece lists 1/4, 3/8, 1/2, 5/8 and 3/4-inch chisels. The TEKTON title says 1/2, 3/4 and 1 inch while its bullets say 1/4, 3/8 and 1/2 inch, so confirm before ordering.
What does the HRC number mean?
The HORUSDY lists 54 to 58HRC and the ValueMax lists a 58 to 60HRC edge. The listings present the number as the edge’s hardness rating; neither listing defines the scale. The other three listings state no hardness figure.
Which set has a warranty?
The Crescent lists a lifetime limited warranty, and the TEKTON lists no time limits and no receipts. The Mayhew says to call the vendor, which is not a stated term, and the HORUSDY and ValueMax state no warranty.
Are these for metal, wood or masonry?
The listings name cutting rivets, rods and bolts, removing slag, and working steel, brass, bronze, cast iron and aluminum; the TEKTON adds copper to that list. The HORUSDY and ValueMax also name woodworking and masonry. Match the chisel to the material the listing states.
What is the striking cap on the Crescent?
The Crescent listing describes a striking cap design that reduces mushrooming of the head and keeps the holding hand away from contact. Its extended length also keeps the hand clear of obstructions and debris, and the recessed stock gives better control. None of the other four listings states a striking cap.
Related: Best Center Punch for Metal (2026), Best Transfer Punch Set (2026): 5 Sets, Scored, Transfer Punch vs Center Punch: Which One Should You Buy?, Best Center Punch Tool (2026): 4 Compared, and the metal fab tools hub.
Scoring, line by line
Each chisel set is scored out of 10 on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. Cold chisels carry no electrical safety listing, so every set here scores zero on that criterion; the warranty picture splits the group, with one stated warranty and four listings without a concrete term. The ranking comes from steel, hardness, count and the warranty terms.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Crescent 3-Piece | 9.7 | 30 | 21 | 20 | n/a | 3 |
| Mayhew 5-Piece | 9.7 | 32 | 22 | 21 | n/a | 0 |
| TEKTON 3-Piece | 9.6 | 28 | 21 | 20 | n/a | 0 |
| ValueMax 3-Piece | 9.6 | 29 | 20 | 20 | n/a | 0 |
| HORUSDY 3-Piece | 9.5 | 28 | 19 | 19 | n/a | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score. Safety is only scored for powered machines or when a listing names safety features; otherwise it drops out and the score is worked from the other 90 points.




