What Is a Roll Pin Punch: How It Works and When to Use It
A roll pin punch has a small nub that seats inside a hollow roll pin, keeping the punch centered while you drive the pin out or in.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Wheeler Master Roll Pin Punch Set with Dual Sided9.7/10View on Amazon - 2
Real Avid Roll Pin Punch Set & Hammer + Non-Slip9.6/10View on Amazon - 3
BESTNULE 24pc Punch Set and Hammer9.6/10View on Amazon - 4
W WIREGEAR 48Pcs Roll Pin Punch Set with Hammer9.5/10View on Amazon
A pin that will not move is a familiar shop problem. The pin sits flush, the hole is tight, and a flat punch skates off the hollow end and chews the edge. That is the job a roll pin punch is made for. In short, what is a roll pin punch? It is a punch with a small round nub on its tip that seats inside the hollow end of a roll pin, so the punch stays centered while you drive the pin out or in.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Wheeler Master Roll Pin Punch Set with Dual Sided
9 roll punches and 9 starters from 1/16 to 5/16 inch, a dual sided hammer and a molded case, with the only stated lifetime warranty here.
Pros
- 9 roll punches and 9 starters in matching sizes from 1/16 to 5/16 inch
- Dual sided hammer with nylon and brass heads for non-marring contact
- Limited lifetime warranty, the only stated term here
- Molded plastic case keeps the set in one place
Cons
- Punches are chrome plated steel only, with no brass punch for soft work
- No tweezers for handling small pins
- Sizes cover 1/16 to 5/16 inch only, with nothing larger
- No bench block in the box for supporting the work

Real Avid Roll Pin Punch Set & Hammer + Non-Slip
10 nickel plated roll pin punches with a magnetic bench block, 4 hammer heads and a pin alignment tool for small pins.
Pros
- 10 nickel plated steel punches from 1/16 to 9/32 inch, plus a 5/16 inch resin punch
- Magnetic bench block holds the work and catches loose pins
- 4 interchangeable hammer heads: steel, rubber, nylon and brass
- Pin Alignment Tool and non-marring finishing punch included
Cons
- No warranty term is stated
- No starter punches in the set
- The 1911 bushing wrench fits the 1911 only
- No flat pin punches for solid pins

BESTNULE 24pc Punch Set and Hammer
A 24-piece set with roll pin, flat pin and starter punches, an 8 oz hammer with 4 faces, tweezers and wipes.
Pros
- 24 pieces cover roll pin, flat pin, starter and plastic punches
- Punches are heat-treated 40# chrome steel, hardened to HRC 50-55
- Hammer has 4 replaceable faces: brass, chrome steel, nylon and rubber
- Reverse-taper design helps keep punches from binding in pin holes
Cons
- No warranty term is stated
- Roll pin punches come in 1/16 and 3/32 inch only
- Two pin punches are plastic, not steel
- No bench block in the box for supporting the work

W WIREGEAR 48Pcs Roll Pin Punch Set with Hammer
A 48-piece set with 7 brass punches, 40 punches of different sizes, a bench block and 2 cases, with a hammer that swaps between 4 heads.
Pros
- 48 pieces, the largest set here, with 40 punches of different sizes
- 7 brass punches for fine metalwork without scratching
- Bench block included for drifting and riveting work
- 2 blow molded cases with sizes engraved on each slot
Cons
- Maker warns the warehouse may ship the wrong product
- Two cases to store instead of one
- Brass punches are soft by design, so they suit fine work rather than heavy driving
- Built for bench work, so it is less handy on a job away from the bench
What is a roll pin punch
A roll pin punch is a steel punch with a small projecting nub at the center of the face that bears on the pin. The nub fits inside the hollow end of a roll pin and keeps the punch centered on the pin while you strike the other end with a hammer. The punch body matches the pin size, so the flat face around the nub bears on the pin end without entering the hole.
Most roll pin punches are sold in sets that cover a range of pin sizes. The Wheeler set runs from 1/16 to 5/16 inch and the Real Avid set from 1/16 to 9/32 inch, plus a 5/16 inch resin punch, while the BESTNULE roll pin punches come in 1/16 and 3/32 inch and the W WIREGEAR set states no punch sizes. A starter punch carries the same nub and is made for the first taps that break a stuck pin loose and start it moving.
Roll pin punch vs solid pin punch
A solid pin punch has a flat face and is made for solid pins, where the whole face bears on the pin end. A roll pin punch has the nub in the middle, so it centers itself in a hollow pin and cannot skate across the face. Use the roll pin punch on roll pins and the solid punch on solid pins; swapping them is how pin ends get flared and punch tips get chipped.
The BESTNULE set pairs roll pin punches with flat pin punches in the same sizes, so one case covers both kinds of pin. The Wheeler set adds starters in matching sizes, and the Real Avid set adds a bench block.
The four sets side by side
| Gear Score | Roll pin punches | Extras | Case | |
|---|---|---|---|---|
| Wheeler Master Roll Pin Set | 9.7/10 | 9 roll punches, 1/16 to 5/16 in, plus 9 starters | Dual sided hammer, nylon and brass heads | Molded plastic case |
| Real Avid Roll Pin Punch Set | 9.6/10 | 10 roll pin punches, 1/16 to 9/32 in, plus 5/16 in resin punch | Magnetic bench block, 4 hammer heads | Stand-up case |
| BESTNULE 24pc Punch Set | 9.6/10 | Roll pin punches in 1/16 and 3/32 in | Hammer with 4 faces, tweezers, wipes | Compact organizer box |
| W WIREGEAR 48Pcs Roll Pin Punch Set | 9.5/10 | 40 punches of different sizes, 7 brass punches | Bench block, hammer with 4 heads, tweezers | 2 blow molded cases |
Roll pin punch sets for the shop
Driving a roll pin cleanly comes down to matching the punch to the pin and keeping the punch centered, and these four sets cover that job in different ways, from a matched set of 9 punches and 9 starters to a 48-piece kit with a bench block.
How to use a roll pin punch
Support the work so the pin has somewhere to go, then pick the punch that matches the pin size. The nub should seat in the hollow end with the flat face resting on the pin end. Start the pin with a starter punch if the set has one, then switch to the matching roll pin punch and drive the pin with steady hammer taps, keeping the punch straight and the work supported.
Keep the punch straight through the whole drive. A punch held at an angle loads the edge of the pin and can bend the punch or flare the pin mouth. When the pin is out, check the hole and the pin before reuse: a pin with a flared mouth or a bent wall belongs in the scrap bin, not back in the hole.
Wear eye protection when driving pins. A pin under spring pressure can jump when it breaks loose, and a chipped punch tip can throw a fragment. Safety glasses under a face shield are sensible on this job.
FAQ for welders
What is a roll pin punch used for?
A roll pin punch drives hollow roll pins, also called spring pins, in and out of their holes. The nub on its tip seats inside the hollow end of the pin and keeps the punch centered, so the pin moves straight instead of flaring at the mouth. It is the right punch for roll pins in hinges, linkages, handles and machine parts.
How is a roll pin punch different from a solid pin punch?
A solid pin punch has a flat face for solid pins. A roll pin punch has a small nub in the middle of its face that fits inside the hollow end of a roll pin. Without the nub, a flat punch can skate off a roll pin and flare the pin mouth.
What size roll pin punch do I need?
Match the punch to the pin size, so the nub seats in the hollow end and the flat face bears on the pin end. The Wheeler set runs from 1/16 to 5/16 inch and the Real Avid set from 1/16 to 9/32 inch, plus a 5/16 inch resin punch, while the BESTNULE roll pin punches come in 1/16 and 3/32 inch. When in doubt, pick the punch whose nub seats in the hollow end with the flat face on the pin end.
Do I need a starter punch too?
A starter punch helps with a pin that has sat in place and will not move at first, since its nub starts the pin moving before you switch to the standard punch. The Wheeler set includes 9 starters in the same sizes as its 9 punches, and the BESTNULE set includes hollow end starter punches from 1/16 to 1/8 inch. If your set has no starters, start the pin with light taps and a punch that seats well.
Can I drive a roll pin with a regular punch?
You can, but it is a poor fit: a flat punch has nothing to center on, so it can slip off and flare the pin mouth or chip the punch tip. A roll pin punch keeps the pin moving straight and is the right tool for the job. Keep a roll pin punch in the sizes you use most.
Related: best roll pin punch set, best drift punch set, transfer punch vs roll pin punch, and the metal fab tools hub.




