Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Transfer Punch vs Roll Pin Punch: Which One Should You Buy?

Two TEKTON roll pin punches face a 28-piece HORUSDY transfer set and a self-adjusting ASSORTS aligner: marking hole centers versus driving hollow pins, compared by range, materials and warranty.

Transfer Punch vs Roll Pin Punch: Which One Should You Buy?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1HORUSDY 28-Piece Transfer Punch Set, 3/32" - 1/2"HORUSDY 28-Piece Transfer Punch Set, 3/32" - 1/2"9.6/10View on Amazon
  2. 2TEKTON 1/8 Inch Roll Pin Punch | 66064TEKTON 1/8 Inch Roll Pin Punch | 660649.6/10View on Amazon
  3. 3TEKTON 3/32 Inch Roll Pin Punch | 66063TEKTON 3/32 Inch Roll Pin Punch | 660639.6/10View on Amazon
  4. 4Universal Transfer Center AlignerUniversal Transfer Center Aligner9.6/10View on Amazon

Verdict. For transfer punch vs roll pin punch, the choice is about the job: transfer punches mark hole centers for drilling, while roll pin punches drive hollow pins in and out. Pick the HORUSDY 28-piece set or the ASSORTS aligner when you need to copy a bolt pattern onto a new plate, and pick one of the TEKTON roll pin punches when the job is removing or installing spring pins. The two TEKTON listings are the only ones here that state a warranty.

The bracket is drilled, the new plate is blank, and the hole pattern has to land in exactly the right spots. That is transfer punch work. A roll pin that will not budge is a different job, and that is where a roll pin punch earns its keep. For transfer punch vs roll pin punch, the short answer is that the two do not replace each other: one marks, the other drives. This comparison puts two transfer tools against two TEKTON roll pin punches, using only what each listing states.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

The four punches

HORUSDY 28-Piece Transfer Punch Set, 3/32" - 1/2"

HORUSDY 28-Piece Transfer Punch Set, 3/32" - 1/2"

HORUSDY9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 28-piece transfer punch set from 3/32 to 1/2 in in 1/64 in steps, in heat treated alloy steel with an index stand.

Pros

  • 28 punches cover 3/32 to 1/2 in by 1/64 in, including 17/32 in
  • Heat treated alloy steel with a black oxide film for rust resistance
  • Index stand keeps the set stacked and ready to pull
  • One purchase covers the common transfer sizes for tool builders and mechanics

Cons

  • No warranty is stated
  • No safety certification is stated
  • 28 pieces to store and keep in order
  • No per-piece hardness figure is stated
TEKTON 1/8 Inch Roll Pin Punch | 66064

TEKTON 1/8 Inch Roll Pin Punch | 66064

TEKTON9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 1/8 in roll pin punch in high carbon steel with a reverse taper and guide ball tip, individually heat treated and made in the USA.

Pros

  • Reverse taper with guide ball tip self centers on hollow pins
  • Individually heat treated for tip hardness and temper of the striking end
  • High carbon steel, straight and true with a precisely machined tip
  • Warranty states no time limits and no receipts

Cons

  • Single 1/8 in size; a set must be built one punch at a time
  • No safety certification is stated
  • No case or index stand is listed
  • Made for hollow pins, not for marking hole centers
TEKTON 3/32 Inch Roll Pin Punch | 66063

TEKTON 3/32 Inch Roll Pin Punch | 66063

TEKTON9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 3/32 in roll pin punch with the same reverse taper, guide ball tip and individual heat treatment as its 1/8 in sibling.

Pros

  • Reverse taper with guide ball tip self centers on hollow pins
  • Individually heat treated for tip hardness and temper of the striking end
  • High carbon steel, straight and true with a precisely machined tip
  • Warranty states no time limits and no receipts

Cons

  • Single 3/32 in size; a set must be built one punch at a time
  • No safety certification is stated
  • No case or index stand is listed
  • Made for hollow pins, not for marking hole centers
Universal Transfer Center Aligner

Universal Transfer Center Aligner

ASSORTS9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A single CNC-made transfer center aligner that self-adjusts to holes from 3/8 to 1 in, replacing a drawer of fixed-size transfer punches.

Pros

  • One tool covers 3/8 to 1 in holes
  • CNC made with a hardened guide cone and a knurled body for grip
  • Replaces the need for different sized regular transfer punches, per the listing
  • Oversize pin head will not slip out through the body

Cons

  • No warranty is stated
  • No safety certification is stated
  • Smaller holes need a different tool
  • One tool only; no index stand or case is listed

Other welders and gear to compare

Side by side

TEKTON 1/8 in Roll Pin Punch TEKTON 3/32 in Roll Pin Punch HORUSDY 28-Pc Transfer Punch Set ASSORTS Transfer Center Aligner
Side Roll pin Roll pin Transfer Transfer
Size range 1/8 in single; line spans 1/16 to 3/8 in 3/32 in single; line spans 1/16 to 3/8 in 3/32 to 1/2 in, 28 pieces 3/8 to 1 in, single tool
Tip Reverse taper, guide ball Reverse taper, guide ball Not stated Hardened guide cone
Material High carbon steel High carbon steel Heat treated alloy steel Tool steel, EN31 pin
Weight 1.28 oz 0.8 oz Not stated 0.14 kg
Warranty No time limits, no receipts No time limits, no receipts Not stated Not stated

All specs here repeat what the maker rates and the listing prints, copied down 22 October 2026. No listing here states a CSA, UL or ETL listing.

Transfer punch vs roll pin punch: the core difference

A transfer punch drops into an existing hole and marks its center on the plate behind it, so the new holes land where the old ones were. A roll pin punch carries a small projecting tip that fits inside a hollow pin, so the hammer force drives the pin instead of spreading it. The HORUSDY set covers 3/32 to 1/2 in in 1/64 in steps with an index stand; the ASSORTS tool is a single self-adjusting aligner for 3/8 to 1 in holes. The two TEKTON punches are single 1/8 in and 3/32 in tools, each with a reverse taper and guide ball tip.

Sizes and range

The HORUSDY set gives the widest stated coverage: 28 punches from 3/32 to 1/2 in by 1/64 in, including a 17/32 in punch. The ASSORTS aligner takes a different approach with one tool for 3/8 to 1 in holes, and the listing says it replaces the need for different sized regular transfer punches. Each TEKTON listing is for a single punch, 1/8 in or 3/32 in, though the spec table lists size options from 1/16 to 3/8 in for the line. If your holes run smaller than 3/8 in, the ASSORTS cannot cover them; if they run above 17/32 in, the HORUSDY set cannot either.

Materials and build

HORUSDY states heat treated alloy steel with a black oxide film. ASSORTS states tool steel with an EN31 hardened pin, a CNC-made body and a knurled grip. Both TEKTON punches state high carbon steel with individual heat treatment and a dry-touch, rust-preventative coating on a natural finish. The listings do not share enough of the same specs to name a build winner across the two sides, so treat each material claim as that listing’s own.

Warranty

Both TEKTON listings state the same warranty: no time limits, no receipts, at tekton.com/warranty. The HORUSDY and ASSORTS listings state no warranty. That is the clearest paper difference between the two sides here, and it is part of why the TEKTON punches score higher.

Choose transfer punches if

  • You copy bolt patterns from drilled parts to blank plates.
  • You want 28 indexed sizes in one purchase, with the HORUSDY set.
  • You prefer one self-adjusting tool for 3/8 to 1 in holes, with the ASSORTS aligner.
  • Marking centers before drilling is the whole job.

Choose roll pin punches if

  • You drive spring pins and roll pins in and out of hinges and linkages.
  • You need the guide ball tip that centers inside a hollow pin.
  • A no-time-limit warranty matters to you.
  • 1/8 in or 3/32 in covers the pins you meet.

FAQ for welders

What is a transfer punch used for?

A transfer punch drops into an existing hole and marks its center on the plate behind it, so drilled holes land in the right spots. The HORUSDY set covers 3/32 to 1/2 in, and the ASSORTS aligner self-adjusts to holes from 3/8 to 1 in.

What is a roll pin punch used for?

A roll pin punch drives hollow spring pins in and out. The TEKTON punches use a reverse taper with a guide ball tip that centers inside the pin so the hammer force drives it instead of spreading it.

Can a transfer punch drive out a roll pin?

That is not its job. A transfer punch marks centers; it has no guide tip made to drive inside a hollow pin, so use one of the roll pin punches for pin work and keep the transfer tools for marking.

Which of these state a warranty?

The two TEKTON listings state no time limits and no receipts. The HORUSDY and ASSORTS listings state no warranty.

Which covers the widest size range?

The HORUSDY set: 28 punches from 3/32 to 1/2 in. The ASSORTS covers 3/8 to 1 in with one tool, and each TEKTON is a single size, 1/8 in or 3/32 in.

Related: our metal fab tools hub, the best center punch tool roundup, and best center punch for hardened steel.

Scoring, line by line

All four are scored on performance, build, value, safety listing and warranty, with the weights published on our How We Pick page. No listing states a safety certification, so safety scores zero across the board; the two TEKTON listings are the only ones that state a warranty.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
HORUSDY 28-Pc Transfer Punch Set 9.6 30 21 21 n/a 0
TEKTON 1/8 in Roll Pin Punch 9.6 29 21 20 n/a 0
TEKTON 3/32 in Roll Pin Punch 9.6 28 21 20 n/a 0
ASSORTS Transfer Center Aligner 9.6 28 20 20 n/a 0

A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number. Unpowered items with no stated safety features skip the safety line, and their score comes from the 90 points that are left.

Before you swing a hammer. Wear safety glasses when striking any punch, since hardened steel can chip. Hold the punch square to the work and strike the head, never the tip. Clamp or brace the workpiece so it cannot shift or fall. Keep fingers clear of the strike zone.

More buying guides

Metal Fab Tools ·

Best Roll Pin Punch Set (2026)

Five roll pin punch sets compared by size range, tip, steel, handles and storage for automotive, machinery and gunsmithing work.