Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Best Metal Knockout Hole Punch Set (2026)

Five manual knockout punch sets compared for conduit and panel holes, with sizes, thickness limits, and kit contents from the listings.

Best Metal Knockout Hole Punch Set (2026)
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1VEVOR Knockout SetBest OverallVEVOR Knockout Set9.5/10View on Amazon
  2. 2TEMCo TH0390Best for Tight AreasTEMCo TH03909.5/10View on Amazon
  3. 3AMZCNC 6-Die SetBest Forged SteelAMZCNC 6-Die Set9.5/10View on Amazon
  4. 4iGeelee CC-60Best Kit ContentsiGeelee CC-609.4/10View on Amazon
  5. 5AMZCNC 4-Die SetBest Small RangeAMZCNC 4-Die Set9.4/10View on Amazon

A panel box that needs a clean round hole is a job where a drill and a hole saw leave a ragged edge and a slow cleanup. The best metal knockout hole punch set answers that job with a punch and die that cut a round hole with clean edges and a uniform size. This guide compares the manual sets by conduit size range, steel thickness limits, materials, and kit contents, using only what each listing states.

WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

Quick picks

  • Best Overall VEVOR Knockout Set: 6 dies to 2 inch, step drill, socket, and case in 40Cr steel. Check price on Amazon
  • Best for Tight Areas TEMCo TH0390: Manual punches for tight areas, slug splitting, alignment marks. Check price on Amazon
  • Best Forged Steel AMZCNC 6-Die Set: Forged 5140 steel to HRC48, 6 punches to 2 inch, cased kit. Check price on Amazon
  • Best Kit Contents iGeelee CC-60: Wrench, 6 drill bits, 2 pull rods, connector, red case. Check price on Amazon
  • Best Small Range AMZCNC 4-Die Set: Compact 4-die set to 1-1/4 inch in forged 5140 steel. Check price on Amazon

The machines

VEVOR Knockout Punch Set

VEVOR Knockout Punch Set

VEVOR9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A manual knockout set with 6 round dies from 1/2 to 2 inch, 2 pull rods, a wrench, a socket, a step drill, and a case, in 40Cr steel.

Pros

  • 6 round dies from 1/2 to 2 inch, stated as 22.5 to 61.5 mm
  • Ratchet wrench with forward and reverse punching and a non-slip curved handle
  • Laser scale markings with dual inch-millimeter units for positioning
  • Stated limits of 1/8 inch for low-carbon steel and 1/16 inch for stainless steel

Cons

  • No warranty term is stated
  • No safety standard is stated
  • Weight of 9.3 pounds is the heaviest stated weight here
  • Case dimensions are not stated, only set dimensions of 11.02 by 2.56 by 10.04 inches
TEMCo TH0390 – Manual Knockout Punch Driver Kit

TEMCo TH0390 – Manual Knockout Punch Driver Kit

TEMCo Industrial9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A manual knockout punch driver kit for 1/2 to 2 inch conduit, with slug splitting punches, laser engraved alignment marks, and a rugged case.

Pros

  • Conduit punch sizes from 1/2 to 2 inch with slug splitting design
  • Laser engraved alignment marks on the punch dies for positioning
  • Mild steel capacity through 10 gauge (3.5 mm) stated
  • Dies compatible with THA001 draw stud, TH0004 and TH0037 drivers, and GREENLEE tooling

Cons

  • No warranty term is stated
  • No safety standard is stated
  • No case dimensions are stated
Manual Knockout Hole Punch Driver Kit 1/2 to 2

Manual Knockout Hole Punch Driver Kit 1/2 to 2

AMZCNC9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A manual knockout kit with 6 punches from 1/2 to 2 inch in forged 5140 steel, heat treated to HRC48, with a wrench and 2 pull rods.

Pros

  • 6 punches from 1/2 to 2 inch for conduit sizes
  • Forged 5140 steel, heat treated to HRC48 hardness
  • Stated limits of 1/8 inch for steel and 1/16 inch for stainless steel
  • Wrench, 6 punches, and 2 pull rods packed in a plastic case

Cons

  • No warranty term is stated
  • No safety standard is stated
  • Stainless steel limited to soft alloys only in the listing
  • Weight stated as 4.19 kg, with no case dimensions stated
Ratchet Knockout Hole Punch Driver Kits 1/2 to 2

Ratchet Knockout Hole Punch Driver Kits 1/2 to 2

iGeelee9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A manual knockout set with 6 punches from 22.5 mm to 61.5 mm in hardened steel, with a wrench, 6 drill bits, 2 pull rods, and a connector in a red case.

Pros

  • 6 punches in sizes 22.5, 28.3, 34.6, 43.2, 49.6, and 61.5 mm
  • Hardened steel punches for mild steel, aluminum, fiberglass, and plastic
  • Long handle with an ergonomic structure for easier use
  • Kit includes 6 drill bits, 2 pull rods, and a connector in a red plastic case

Cons

  • No warranty term is stated
  • No safety standard is stated
  • No thickness limit is stated
  • Title calls it a ratchet kit while the kit list names a wrench, with no ratchet wrench named
Manual Knockout Punch Driver Die Set 1/2-1-1/4

Manual Knockout Punch Driver Die Set 1/2-1-1/4

AMZCNC9.4/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A manual knockout die set for 1/2 to 1-1/4 inch conduit in forged 5140 steel, with 4 dies, 4 punches, and 2 bearing driving bolts.

Pros

  • Forged, machined, and heat treated 5140 steel construction
  • Actual hole diameters of 0.89, 1.11, 1.36, and 1.7 inches stated
  • Mild steel capacity under 10 gauge (3.5 mm) stated
  • Drive-bolt design using several turns of a wrench to apply pressure

Cons

  • No warranty term is stated
  • No safety standard is stated
  • Range stops at 1-1/4 inch, so no 1-1/2 or 2 inch punch
  • Stainless steel, wood, and drywall are barred as workpieces

Other welders and gear to compare

Spec sheet comparison

Set Gear Score Conduit sizes Max steel Material Kit contents Warranty
VEVOR Knockout Set 9.5/10 1/2 to 2 inch 1/8 inch low-carbon; 1/16 inch stainless 40Cr steel 6 dies, 2 pull rods, wrench, socket, step drill, case Not stated
TEMCo TH0390 9.5/10 1/2 to 2 inch 10 gauge (3.5 mm) mild steel Black oxide finish Punches, 19 mm socket, rugged case Not stated
AMZCNC 6-Die Set 9.5/10 1/2 to 2 inch 1/8 inch steel; 1/16 inch stainless 5140 steel 6 punches, 2 pull rods, wrench, case Not stated
iGeelee CC-60 9.4/10 1/2 to 2 inch Not stated Hardened steel 6 punches, 6 drill bits, 2 pull rods, wrench, connector, case Not stated
AMZCNC 4-Die Set 9.4/10 1/2 to 1-1/4 inch Under 10 gauge (3.5 mm) mild steel 5140 steel 4 dies, 4 punches, 2 bearing bolts Not stated

All specs here repeat what the maker rates and the listing prints, copied down 28 October 2026.

Buying guide: best metal knockout hole punch set

Conduit size range

Range decides whether a set covers the job. The VEVOR, TEMCo, AMZCNC 6-die, and iGeelee sets cover 1/2 to 2 inch conduit sizes, while the AMZCNC 4-die set covers 1/2 to 1-1/4 inch, with actual hole diameters of 0.89, 1.11, 1.36, and 1.7 inches. A set that stops at 1-1/4 inch suits smaller panel work, while a set that runs to 2 inch covers larger conduit entries. Match the largest conduit size on the job to the largest punch in the set before buying.

Steel thickness limits

Thickness limits are stated with conditions, and the conditions matter. The AMZCNC 6-die set lists a maximum thickness of 1/8 inch for steel and 1/16 inch for stainless steel, and the VEVOR set lists the same limits, stated as low-carbon steel to 1/8 inch and 10 GA and stainless steel to 1/16 inch and 16 GA. The TEMCo set lists mild steel plate through 10 gauge (3.5 mm), and the AMZCNC 4-die set lists mild steel under 10 gauge (3.5 mm) and bars stainless steel as a workpiece. The iGeelee set states no thickness limit, so its limits are not stated. Never assume a punch that cuts mild steel will cut stainless steel at the same thickness.

Manual drive and slugs

All 5 sets are manual drive sets, worked with a wrench, a ratchet, or a driver. The TEMCo set lists manual drive for use with a ratchet, wrench, or electric driver, plus a 19 mm socket for use with a 1/2 inch ratchet. The VEVOR set lists a ratchet wrench with forward and reverse punching and smooth precision threads. The TEMCo set also lists a slug splitting design on the punches for easier slug removal, leaving a round hole with clean edges and a uniform size. For powered punching instead, see hydraulic knockout punch set.

Kit contents and case

Kit contents separate a complete set from a bare set of dies. The VEVOR set lists 6 round dies, 2 pull rods, a wrench, a socket, a step drill, and a portable storage case. The iGeelee set lists 1 wrench, 6 drill bits, 2 pull rods, and 1 connector in a durable red plastic case. The AMZCNC 6-die set lists 1 wrench, 6 punches, and 2 pull rods in a plastic case. The TEMCo set lists a rugged storage case with a 19 mm socket and a lid that stays closed for transport. The AMZCNC 4-die set lists 4 dies, 4 hole punches, and 2 bearing driving bolts, with no case stated.

Before You Strike an Arc

  • Check the conduit size against the punch sizes: 1/2 to 2 inch for 4 sets here, and 1/2 to 1-1/4 inch for the AMZCNC 4-die set.
  • Check the thickness limit for the metal on the job: 1/8 inch for steel and 1/16 inch for stainless steel where stated, and mild steel through 10 gauge (3.5 mm) for the TEMCo set.
  • Do not punch stainless steel with the AMZCNC 4-die set, since the listing bars stainless steel as a workpiece.
  • Check draw stud compatibility on the TEMCo set: dies are compatible with the THA001 draw stud and with TEMCo hydraulic drivers TH0004 and TH0037, plus GREENLEE tooling with 3/4-16 threads.
  • Check the case contents on arrival: wrench, pull rods, dies, and socket, including the 19 mm socket listed for the TEMCo set and the step drill listed for the VEVOR set.

FAQ for welders

What conduit sizes do these sets cover?

The VEVOR, TEMCo, AMZCNC 6-die, and iGeelee sets cover 1/2 to 2 inch conduit sizes. The AMZCNC 4-die set covers 1/2 to 1-1/4 inch, with actual hole diameters of 0.89, 1.11, 1.36, and 1.7 inches.

How thick a steel can a manual knockout punch cut?

It depends on the listing and the metal. The AMZCNC 6-die set lists 1/8 inch for steel and 1/16 inch for stainless steel, and the VEVOR set lists the same limits. The TEMCo set lists mild steel through 10 gauge (3.5 mm), and the AMZCNC 4-die set lists mild steel under 10 gauge (3.5 mm).

Do these sets work with a ratchet or driver?

The TEMCo set lists manual drive for use with a ratchet, wrench, or electric driver, and it lists a 19 mm socket for use with a 1/2 inch ratchet. The VEVOR set lists a ratchet wrench with forward and reverse punching. The other sets list a wrench or a long handle for manual drive.

What is slug splitting?

The TEMCo listing describes a slug splitting design on the punches that allows for easier slug removal. The design leaves a round hole with clean edges and a uniform size, according to the listing. The VEVOR set carries a SLUG-Buster name in its title, but its bullets describe laser scale markings and dual inch-millimeter units rather than a slug splitting feature.

Is a warranty stated for these sets?

No warranty term is stated for any pick in this guide. Warranty scores are zero across the sets, so the ranking rests on performance, build, and value.

Related: the metal fab tools hub, the best hydraulic knockout punch set, the best hole saw for sheet metal, the best step drill bit for sheet metal, the best sheet metal gauge thickness tool and the best center punch for metal.

Scoring, line by line

Each set is scored on performance, build, value, safety, and warranty. Performance weighs conduit size range and stated thickness limits, build weighs punch material and construction, and value weighs kit contents against gaps. No listing here states a safety standard, so every pick scores zero on safety, and no warranty term is stated for any pick, so the ranking comes from performance, build, and value. How we pick explains the weights.

Product Gear Score Perf. /35 Build /25 Value /25 Safety /10 Warranty /5
VEVOR Knockout Set 9.5 32 22 21 0 0
TEMCo TH0390 9.5 30 21 21 0 0
AMZCNC 6-Die Set 9.5 29 21 20 0 0
iGeelee CC-60 9.4 28 20 20 0 0
AMZCNC 4-Die Set 9.4 26 20 19 0 0

A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number.

More buying guides