Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Remove Broken Screw from Metal

A broken screw stuck in metal comes out with the right extractor for the fastener, and this guide shows the steps and the 4 sets that handle each part of the job.

How to Remove Broken Screw from Metal
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1VEVOR Screw Extractor SetVEVOR Screw Extractor Set9.7/10View on Amazon
  2. 265-Piece Broken Bolt Extractor Kit with Easy Out65-Piece Broken Bolt Extractor Kit with Easy Out9.6/10View on Amazon
  3. 3XEWEA 18PCS Spiral Screw Extractor SetXEWEA 18PCS Spiral Screw Extractor Set9.6/10View on Amazon
  4. 4Bolt Extractor Kit, 14 PCS Impact Bolt & NutBolt Extractor Kit, 14 PCS Impact Bolt & Nut9.5/10View on Amazon

A screw head snaps off flush with the surface, and the rest of the screw sits stuck in the metal with nothing left to grip. An extractor set matched to the fastener gets it out, with a drill where the set needs a pilot hole. This guide shows how to remove broken screw from metal, from the first mark to the last turn, and which extractor set fits the job on the bench.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

VEVOR Screw Extractor Set

VEVOR Screw Extractor Set

VEVOR9.7/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 27-piece set with 25 extractors from 1/8 inch to 7/8 inch, Cr-Mo steel rated HRC50-55, and 2 adapters that fit common drive tools.

Pros

  • 25 extractors cover 1/8 inch to 7/8 inch, the widest stated range here
  • Cr-Mo steel rated HRC50-55 for wear, torsion, and deformation resistance
  • Includes a 1/4 inch to 3/8 inch adapter and a 1/2 inch to 3/8 inch adapter
  • Double-head design connects to common tools without extra sleeves

Cons

  • No drill bits in the box, so a pilot hole needs a separate bit set
  • At 3.9 lb it is the heaviest of the sets that state a weight
  • The case measures 9.13 x 5.98 x 2.05 inches, larger than the GRLCOOD box at 6.57 x 3.74 x 1.57 inches
  • No T-handle chuck in the box for manual turning
65-Piece Broken Bolt Extractor Kit with Easy Out

65-Piece Broken Bolt Extractor Kit with Easy Out

THINKWORK9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 65-piece kit with Cr-Mo and HSS extractors, left-hand drill bits, and 2 depth extractors for tight, confined spaces.

Pros

  • 65 pieces, the most in this guide
  • Left-hand drill bits included with the extractors
  • 2 depth extractors at 2.5 inches and 1.06 inches for different applications
  • 3/8 inch square drive fits hand, air, or power tools

Cons

  • Maker states 8 to 19 mm for the bolt extractors; no screw extractor size range is stated
  • Screw extractor sizes are not given as a range, so matching a small screw takes extra care
  • Needs a wrench, socket, or drill to drive the extractors; no T-handle in the box
  • Depth extractors come in 2 sizes only, 2.5 inches and 1.06 inches
XEWEA 18PCS Spiral Screw Extractor Set

XEWEA 18PCS Spiral Screw Extractor Set

XEWEA9.6/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An 18-piece set with 6542 left-hand drill bits, CR-MO spiral extractors, and a keyless T-handle chuck for manual extraction.

Pros

  • Keyless T-handle chuck with 3/8 inch drive included for manual extraction
  • 6542 HSS left-hand drill bits and CR-MO spiral extractors
  • Duplicate #1, #2, and #3 extractors and matching drill bits for the sizes used most
  • Upgraded #5 dual-step extractor with a reinforced stepped shank

Cons

  • 18 pieces, a smaller kit than the 27-piece and 65-piece sets
  • Tops out at the #5 extractor, with no larger sizes for big bolts
  • No warranty term is stated
  • Hand turning needs the included T-handle chuck or a separate ratchet or drill
Bolt Extractor Kit, 14 PCS Impact Bolt & Nut

Bolt Extractor Kit, 14 PCS Impact Bolt & Nut

GRLCOOD9.5/10 Gear Score
i
The Gear Score runs from 9.2 to 9.8 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 14-piece socket set with 13 socket sizes from 1/4 inch to 3/4 inch, a 3/8 inch adapter, and a palm-sized blow-molded case.

Pros

  • 13 socket sizes from 1/4 inch to 3/4 inch, laser etched for identification
  • Internal left-hand spiral inside each socket grips damaged bolt and nut heads
  • Maker states use with power and hand tools
  • Palm-sized blow-molded case keeps the set organized and easy to carry

Cons

  • 14 pieces, the smallest set here
  • Socket design fits over the head, so it does not help when a screw is broken flush with nothing to grip
  • Tops out at 3/4 inch, so larger bolts need a bigger set
  • No warranty term is stated

How to Remove a Broken Screw from Metal, Step by Step: how to remove broken screw from metal

For an internal extractor, work in this order: mark the center of the broken screw, drill a pilot hole, seat the extractor in the hole, then turn it out counterclockwise with a T-handle or a wrench. Where the set includes left-hand drill bits, the maker states the bits help loosen seized hardware while you drill. For an external socket extractor, fit the socket over the damaged head instead; no pilot hole is drilled. If the fastener does not move, re-seat the extractor and try again with steady pressure instead of forcing the turn.

Clamp the work before you drill, and wear eye protection while drilling and turning. Keep gloves away from the chuck and any spinning bit, and keep guards in place on the drill. A broken screw is a small job, and steady pressure with the right extractor beats a hard yank that can snap the tool.

Pick the Right Extractor Size

Match internal extractors to the screw diameter and socket extractors to the size across the bolt or nut head: too small and the extractor slips, too large and it cannot grip. Use the size chart in the screw extractor size chart to match the fastener to the extractor, then check that the set you buy covers that size. The VEVOR set lists internal extractors from 1/8 inch to 7/8 inch, the THINKWORK maker states 8 to 19 mm for the bolt extractors, and the GRLCOOD set lists socket sizes from 1/4 inch to 3/4 inch. The screw extractor set how to use guide walks through the drill, seat, and turn sequence for internal extractors.

Extractor Sets for Broken Screws in Metal

Together the sets below cover each part of the same job: drill bits open the pilot hole where one is needed, internal extractors grip inside the hole and socket extractors grip the outside of the head, and drive adapters and the chuck connect the set to the tools on the bench.

The 4 Sets Side by Side

Set Pieces Extractor sizes Material Weight Gear Score
VEVOR 27-Piece Screw Extractor Set 27 1/8 in to 7/8 in Cr-Mo steel, HRC50-55 3.9 lb 9.7/10
THINKWORK 65-Piece Bolt Extractor Kit 65 8 to 19 mm (bolt sizes) Cr-Mo steel and HSS Not stated 9.6/10
XEWEA 18-Piece Spiral Extractor Set 18 #1, #2, #3, #5 6542 HSS bits, CR-MO extractors 0.5 lb 9.6/10
GRLCOOD 14-Piece Bolt Extractor Kit 14 1/4 in to 3/4 in (socket sizes) High-hardness alloy steel 1.57 lb 9.5/10

The VEVOR set lists the widest stated inch range for internal extractors, from 1/8 inch to 7/8 inch, and the THINKWORK set holds the most pieces at 65. The XEWEA set is the only one here with a T-handle chuck in the box.

FAQ for welders

Do I need a drill to remove a broken screw from metal?

It depends on the extractor type. Internal extractors need a pilot hole, and the THINKWORK and XEWEA sets include left-hand drill bits for that hole. The VEVOR set holds internal extractors without bits, so the pilot hole needs a separate bit set. The GRLCOOD socket (on Amazon) set fits over the damaged head and needs no pilot hole.

What size screw extractor do I need?

Match internal extractors to the screw diameter and socket extractors to the size across the head. The VEVOR set lists internal extractors from 1/8 inch to 7/8 inch, the THINKWORK maker states 8 to 19 mm for the bolt extractors, and the GRLCOOD set lists socket sizes from 1/4 inch to 3/4 inch. Check the size chart before ordering so the set you buy covers the fastener in front of you.

Can a screw extractor remove a rusted screw?

The makers list rusted or stuck fasteners for the GRLCOOD, THINKWORK, and XEWEA sets, and rounded fasteners for the VEVOR set. For internal extractors, drill the pilot hole, seat the extractor, and turn with steady pressure. If the fastener does not move, re-seat the extractor and try again rather than forcing the turn.

Can I use a screw extractor with a power drill?

Follow the drive guidance for the set you buy. The GRLCOOD maker states use with power and hand tools, and the THINKWORK set uses a 3/8 inch square drive stated for hand, air, or power tools. The XEWEA set works with power drills, ratchets, and the included T-handle chuck, and the VEVOR set includes adapters stated to support torque wrenches and electric drills. Turning an internal extractor by hand with a T-handle or wrench gives the most control over the turn.

What is the difference between a spiral extractor and a multi-spline extractor?

A spiral extractor is an internal extractor with spiral flutes; the THINKWORK maker states the flutes bite down as resistance increases, and the XEWEA set uses CR-MO spiral extractors. The VEVOR set uses hex head multi-spline internal extractors instead, with a double-head design that connects directly to common tools without extra sleeves. Both internal types need a pilot hole drilled first. The GRLCOOD set is different again: its sockets fit over the outside of the head, with an internal left-hand spiral inside the socket, and need no pilot hole.

Related: best screw extractor set, best screw extractor, thread repair kit, and the metal fab tools hub.

More buying guides

Metal Fab Tools ·

How to Remove Powder Coating From Metal

Chemical strippers lift coatings off metal to bare metal, and this guide covers the liquid, aerosol and gel forms plus the etch that preps…