Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Change a Chop Saw Blade

How to change a chop saw blade: unplug the saw, lock the spindle, swap the wheel for one that matches the diameter, arbor and max RPM, and check it runs true.

How to Change a Chop Saw Blade
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Luckyway 12 Inch Miter Saw Blades 32T&80T with 1 Inch ArborLuckyway 12 Inch Miter Saw Blades 32T&80T with 1 Inch Arbor9.7/10View on Amazon
  2. 2DEWALT DW8020 Metal Port Saw Cut-Off WheelDEWALT DW8020 Metal Port Saw Cut-Off Wheel9.7/10View on Amazon

A chop saw starts to wander and throw sparks sideways when the wheel is worn down, and a fresh wheel brings the cut back to straight. To change a chop saw blade, unplug the saw, lock the spindle, take off the arbor bolt and the outer flange, lift the old wheel out, fit the new wheel the right way round, and tighten the bolt before the guard goes back down. This guide shows how to change a chop saw blade step by step, and how to match the new wheel to the saw using the sizes the listings state.

This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

How to change a chop saw blade: the short answer

Unplug the saw first, then lock the spindle and remove the arbor bolt and the outer flange. Lift the old wheel off, check the new wheel for the right diameter, arbor and max RPM, and fit it with the rotation arrow pointing the way the saw turns. Tighten the arbor bolt, check that the wheel runs true, and lower the guard before plugging the saw back in. The sections below cover each step and the sizes to check.

Abrasive wheel or toothed blade

A chop saw wheel is either abrasive or toothed, and each cuts in a different way. An abrasive cut-off wheel grinds through metal, while a toothed blade slices it: the FOXBC cermet blade lists 72 teeth for metal studs and tubing, while the Luckyway TCT blades (on Amazon) list 32 and 80 teeth for wood on a miter saw. Either type can fit a 14 inch chop saw, so match the wheel to the material and to the saw’s speed, and never fit a wood blade to a metal chop saw.

Abrasive cut-off wheel Cermet carbide blade Wood miter blade
Diameter 14 in 14 in 12 in
Thickness or kerf 1/8 in 0.095 in kerf 0.106 in kerf
Arbor 1 in 1 in 1 in
Max RPM 4,400 1,800 4,500
Material Metal and stainless steel Metal studs and tubing Wood, plywood, melamine
Use Chop saw 14 in chop saw 12 in miter saw

Check the max RPM on the label before fitting a wheel. The HBSS and FOXBC cut-off wheels state 4,400 RPM, the Luckyway blades state a 4,500 RPM max, and the FOXBC cermet blade states a 1,800 RPM max. A wheel rated below the saw’s speed should not be fitted.

Before you start

  • Unplug the saw. Pull the plug before touching the wheel, so the saw cannot start while your hands are near the blade.
  • Check the new wheel. Match the diameter and arbor to the saw, check the max RPM covers the saw’s speed, and check the wheel for cracks or chips before fitting it.
  • Clear the bench. Move offcuts and tools away from the saw so the wheel and flanges have somewhere clean to sit.
  • Wear eye protection. A cut-off wheel throws sparks and grit, so wear eye protection and keep the guard in place.

Change the wheel step by step

  1. Unplug the saw and raise the guard to reach the wheel.
  2. Lock the spindle with the saw’s spindle lock, then loosen the arbor bolt with the wrench and lift off the outer flange.
  3. Lift the old wheel off the arbor and note which side faces out, and which way the rotation arrow points where the wheel has one.
  4. Check the new wheel: the diameter and the 1 inch arbor must match the saw, the max RPM must cover the saw’s speed, and the wheel must be free of cracks and chips.
  5. Fit the new wheel on the arbor with the rotation arrow, where the wheel has one, pointing the way the saw turns, then refit the flange.
  6. Tighten the arbor bolt, following the direction in the saw’s manual, and check that the wheel sits flat between the flanges.
  7. Lower the guard, plug the saw back in, and run the wheel briefly to check that it runs true before cutting.

Match the wheel to the saw

Diameter, arbor and max RPM decide whether a wheel fits. The listings here state 14 inch wheels with a 1 inch arbor for chop saws, and 12 inch blades with a 1 inch arbor for miter saws. The HBSS and FOXBC cut-off wheels state 4,400 RPM, the Luckyway blades state a 4,500 RPM max, and the FOXBC cermet blade states a 1,800 RPM max, so a toothed metal blade carries a far lower max RPM figure than an abrasive wheel, and a fast chop saw would run it past that figure. Check the saw’s own label for its speed and fit only a wheel rated for it.

Tooth count decides the finish on a toothed blade. The Luckyway 2-pack lists a 32 tooth blade for general purpose and an 80 tooth blade for fine finish, both 12 inch with a 1 inch arbor. The FOXBC cermet blade lists 72 teeth for metal. An abrasive wheel has no teeth at all: it cuts by grinding, which is why it suits steel and stainless steel where a toothed wood blade would not last.

Read the listing twice

Blade listings contradict themselves, and the numbers that conflict are usually the ones needed to plan the change:

  • HBSS: the bullets state a 1/8 inch thick wheel while the spec table lists 0.039 inches, so the thickness differs between the bullets and the table.
  • Makita: the title states a 14 by 1 by 3/32 inch wheel while the spec table lists 14.17 by 14.17 by 0.67 inches and a weight of 0.000625 pounds.
  • Luckyway: the bullets state a 0.106 inch kerf while the spec table lists a 0.1 inch thickness. Kerf and plate thickness are different measures, so these figures do not contradict each other.
  • OEM home: the bullets offer a conversion ring that lets a 1 inch arbor blade fit a 0.6 inch spindle, so check the arbor before ordering.

Measure the arbor and check the max RPM before ordering. Where the listing gives more than one max RPM figure, trust the lower one, and where it gives more than one thickness, confirm with the maker before ordering.

What this guide does not cover

This guide covers changing the wheel only. It does not cover cutting technique, feed rate or which blade suits a new saw. For blade choices, see the chop saw blade vs cut off wheel guide and the best cut off wheel for square tubing roundup.

Wheel safety. A cut-off wheel can burst if it is cracked, chipped or run past its max RPM, so check the wheel before fitting it and never fit a wheel rated below the saw’s speed. Wear eye protection, keep the guard in place, and clear sparks away from anything flammable. Unplug the saw before changing the wheel. See the OSHA welding overview and our Safety Disclaimer.

FAQ for welders

How do I know which way the arbor bolt turns?

Follow the saw’s manual: the manual states the direction for the saw, and the spindle lock holds the wheel while the bolt turns. Never force the bolt, and check the manual before reaching for a longer wrench.

Can I put a wood blade on a chop saw?

No. The wood blades here are 12 inch miter saw blades, while the chop saw wheels here are 14 inch. Match the blade to the material and to the saw, and check the max RPM before fitting it.

What size wheel does a 14 inch chop saw take?

A 14 inch wheel with a 1 inch arbor. The DEWALT DW8020 (on Amazon), HBSS and FOXBC listings all state 14 inch wheels with a 1 inch arbor, and the HBSS and FOXBC abrasive wheels state 4,400 RPM.

How do I tell if a cut-off wheel is worn out?

Check the wheel for cracks, chips and a worn edge, and check the label for the max RPM before fitting it. A wheel that wobbles or looks damaged should not be fitted, and a wheel that has worn down should be replaced.

Do I need new flanges with a new wheel?

Not usually. Reuse the flanges that came with the saw, and check that they sit flat on the wheel before tightening the bolt. Replace a flange that is bent or cracked.

Related: cut off wheel vs cold saw, diamond vs abrasive cut off wheel, metal circular saw vs chop saw, best saw blade for cutting metal roofing, and the metal fab tools hub.

More buying guides