Best Chop Saw Blade for Steel (2026): 4 Compared
Four chop saw blades for steel compared on size, tooth count, RPM rating, arbor fit and warranty, scored for home shop cutting.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Top PickDiablo D1472CF 14in9.6/10View on Amazon - 2
Mild Steel PickEvolution 14BLADEST9.6/10View on Amazon - 3
Cold Cut PickHARDWIN 66T 14in9.6/10View on Amazon - 4
Capacity PickOSTTE 72T 14in9.6/10View on Amazon
A chop saw turns steel cutting from a workout into a quick trigger pull, but only with the right blade. The best chop saw blade for steel here is a 14-inch cermet blade with 72 teeth and an 1800 RPM rating, claiming up to 25 times longer life than standard blades. This guide compares four steel-cutting blades on size, teeth, RPM rating, arbor fit and warranty.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Top Pick Diablo D1472CF 14in: 14 in 72T cermet II blade, 1800 max RPM, up to 25x longer life claimed. Check price on Amazon
- Mild Steel Pick Evolution 14BLADEST: 14 in 66T carbide blade for mild steel, no heat or burrs, 1600 RPM. Check price on Amazon
- Cold Cut Pick HARDWIN 66T 14in: 14 in 66T cermet cold cut blade, max 1500 RPM, mild steel only. Check price on Amazon
- Capacity Pick OSTTE 72T 14in: 14 in 72T cermet-blend blade, 1 in arbor, rated by walls, plates and rods ranges. Check price on Amazon
The machines

Diablo Steel Demon Cermet II Saw Blade for Medium
A 14-inch 72-tooth cermet II blade for medium metal, rated 1800 RPM max with a 30-day limited warranty.
Pros
- 72 cermet II teeth, 1800 max RPM
- Up to 25x longer life claimed
- Up to 50x cooler, 10x faster claimed
- Stabilizer vents, triple chip grind
Cons
- Arbor size not stated
- 14-inch only, no smaller option
- Claims are listing figures, not measured
- 30-day warranty is short

Evolution Power Tools 14BLADEST Blade for Cutting
A 14-inch 66-tooth carbide TCT blade for mild steel with no heat, no burrs and virtually no sparks.
Pros
- Japanese carbide teeth, 66T
- No heat, no burrs, virtually no sparks
- Thin .094 in kerf for accurate cuts
- 1 in arbor fits chop and circular saws
Cons
- Mild steel only, not hardened or galvanized
- No warranty stated
- 66 teeth, fewer than the 72T picks
- 1600 RPM max, lower than the Diablo top pick

14-Inch 66T Cermet Metal-Cutting Blade for Mild
A 14-inch 66-tooth cermet cold cut blade for mild steel, max 1500 RPM with a 1-inch arbor.
Pros
- 66T cermet TCG geometry
- Cold cut, virtually no sparks
- Max 1500 RPM for dry cut saws
- 1 in arbor fits Evolution, DeWalt, Milwaukee
Cons
- Max 1500 RPM, needs a low-RPM saw
- Mild steel only, not stainless or cast iron
- No warranty term stated
- Verify arbor fit before ordering, as the listing advises

14-Inch 72-Tooth Cold Cut Metal Saw Blade
A 14-inch 72-tooth cermet-blend blade for mild steel with a 1-inch arbor, rated by cut capacity.
Pros
- 72 teeth, 14 in, 1 in arbor
- Cuts walls, plates and rods by range
- Laser-cut stabilizer vents
- Fits standard 14 in metal cutting saws
Cons
- No RPM figure stated
- No warranty term stated
- Cermet-blend, not full cermet
- Wall/plate/rod ranges only, no general rating
Other welders and gear to compare
Diablo Steel Demon Cermet II Saw Blade for Medium MetalCheck price on Amazon
Diablo Steel Demon Cermet II Saw BladeCheck price on Amazon
ANGELSWORD 14" Metal Chop Saw Blade for Mild SteelCheck price on Amazon
FOXBC 14 Inch Metal Steel Cutting Saw Blade 72 Tooth forCheck price on Amazon
FOXBC 14 Inch Metal Steel Cutting Saw Blade 66 Tooth forCheck price on Amazon
Spec sheet comparison
| Blade | Size | Teeth | Max RPM | Arbor | Warranty |
|---|---|---|---|---|---|
| Diablo D1472CF 14in | 14 in | 72 cermet II | 1800 | Not stated | 30-day limited |
| Evolution 14BLADEST | 14 in | 66 carbide | 1600 | 1 in | None stated |
| HARDWIN 66T 14in | 14 in | 66 cermet | 1500 | 1 in | Not stated |
| OSTTE 72T 14in | 14 in | 72 cermet-blend | Not stated | 1 in | Not stated |
All specs here repeat what the maker rates and the listing prints, copied down 20 October 2026.
How to choose the best chop saw blade for steel
Size and arbor
All four picks are 14-inch blades, the standard chop saw size. Three of the four state a 1-inch arbor: the Evolution, the HARDWIN and the OSTTE. The Diablo D1472CF states no arbor size, so verify the arbor before ordering, as the HARDWIN listing advises.
Tooth count and material
Tooth counts run 66 to 72: the two 72-tooth blades suit finer cuts, and the 66-tooth blades suit mild steel work. Tooth materials are cermet or carbide across all four. The Diablo D1472CF claims up to 25 times longer life with cermet II teeth; the Evolution uses Japanese carbide.
RPM match
Stated maximums run 1500 to 1800 RPM: the HARDWIN caps at 1500 RPM for low-RPM dry cut saws, the Evolution at 1600 and the Diablo D1472CF at 1800. The OSTTE states no RPM figure. Never spin a blade faster than its stated maximum.
Mild steel versus thick metal
The Evolution and HARDWIN are stated for mild steel only, with warnings against hardened steel, stainless and cast iron. The Diablo D1472CF is stated for medium metal including cast iron. The OSTTE lists walls, plates and rods by thickness range.
Before You Strike an Arc
- Clamp the workpiece and wear eye protection, gloves and hearing protection; cutting steel throws hot chips.
- Verify the blade’s stated maximum RPM against your saw before mounting.
- Let the blade cut at its own pace; forcing it overheats teeth and shortens life.
- Keep flammables clear: even low-spark blades throw some sparks.
FAQ for welders
What size blade does a chop saw take?
Most take 14-inch blades, which covers all four picks here. Three of the four state a 1-inch arbor; the Diablo D1472CF states no arbor size, so verify fit before ordering.
Can these cut stainless steel?
The Diablo D1472CF lists cast iron and ferrous metals among compatible materials. The Evolution and HARDWIN are stated for mild steel only and warn against stainless, hardened steel and cast iron.
How long do cermet blades last?
Listing claim: up to 25 times longer life for the Diablo D1472CF against standard blades. This is the listing’s claim, not our measurement.
Do I need a special saw?
Cold cut blades like the HARDWIN are stated for low-RPM dry cut saws with a 1500 RPM maximum. Standard chop saws suit the Diablo D1472CF and the Evolution at their stated RPM ratings.
Which have a warranty?
The Diablo D1472CF states a 30-day limited warranty. The Evolution states no warranty, and the other two state no warranty term.
Related: the best chop saw for metal cutting, the best cold cut saw, the abrasive chop saw vs cold saw and the dry cut saw vs abrasive chop saw.
Scoring, line by line
Each blade is scored on performance, build, value, safety and warranty. Safety scores reflect stated safety-relevant features such as stabilizer vents and spark reduction; warranty scores reflect stated warranty terms. Two listings state no warranty term and one states no warranty.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Diablo D1472CF 14in | 9.6 | 30 | 21 | 21 | 7 | 2 |
| Evolution 14BLADEST | 9.6 | 30 | 21 | 20 | 7 | 0 |
| HARDWIN 66T 14in | 9.6 | 29 | 21 | 20 | 7 | 0 |
| OSTTE 72T 14in | 9.6 | 29 | 21 | 20 | 5 | 0 |
A pick’s weighted total decides where it lands between a 9.2 floor and a 9.8 ceiling, and a bigger total never produces a smaller number.




