Best Saw Blade for Cutting Metal Roofing (2026): 5 Picks Compared
5 circular saw blades compared by diameter, tooth count, kerf, arbor and max RPM, for cutting thin metal roofing panels.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallDiablo Steel Demon9.7/10View on Amazon - 2
Best for Stainless SteelFOXBC 48T Cermet9.6/10View on Amazon - 3
Best for Metal RoofingEcho Corner 6-1/29.6/10View on Amazon - 4
Best 48T CermetHARDWIN 48T Cermet9.6/10View on Amazon - 5
Best for Mild SteelEvolution 185BLADEST9.6/10View on Amazon
A roof job starts with a stack of painted panels and a circular saw, and the blade has to cut thin steel without tearing the edge or cooking the paint. This guide compares the best saw blade for cutting metal roofing picks by what each listing states: diameter, tooth count, kerf, arbor and max RPM. The 5 blades here run from a 6-1/2 inch blade to 7-1/4 inch blades, and the Evolution blade is made for mild steel only, so check the material before you cut.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
Quick picks
- Best Overall Diablo Steel Demon: A 7-1/4 inch, 70-tooth blade for thin metal, 12 gauge or thinner, with a triple chip grind. Check price on Amazon
- Best for Stainless Steel FOXBC 48T Cermet: A 7-1/4 inch, 48-tooth cermet blade for metal and stainless steel, with stated thickness ranges. Check price on Amazon
- Best for Metal Roofing Echo Corner 6-1/2: A 6-1/2 inch, 40-tooth cermet blade listed for metal roofing, siding and thin sheets. Check price on Amazon
- Best 48T Cermet HARDWIN 48T Cermet: A 7-1/4 inch, 48-tooth cermet blade for steel, angle iron and threaded rod. Check price on Amazon
- Best for Mild Steel Evolution 185BLADEST: A 7-1/4 inch, 40-tooth TCT blade for mild steel only, with virtually no sparks. Check price on Amazon
The machines

Diablo Steel Demon Carbide Saw Blade for Thin
A 7-1/4 inch, 70-tooth carbide blade for thin metal, 12 gauge or thinner, with a triple chip grind and a Perma-SHIELD coating.
Pros
- 70 teeth with a triple chip grind for fast, burr-free cuts in thin metal
- Made for mild steel, 12 gauge or thinner
- Laser-cut stabilizer vents trap noise and vibration for straight cuts
- Perma-SHIELD coating protects against gumming and corrosion
Cons
- No warranty term is stated
- No arbor size is stated
- No max RPM is stated
- Limited to mild steel, 12 gauge or thinner

FOXBC 7-1/4 inch Circular Saw Blade Metal
A 7-1/4 inch, 48-tooth cermet blade for metal and stainless steel, with a .075 inch kerf, a 5/8 inch arbor and a 5800 max RPM.
Pros
- Cuts metal and stainless steel, with cermet carbide teeth
- Stated thickness ranges for studs, tubing, plates, bars and rods
- Laser-cut stabilizer vents trap noise and vibration
- Maker claims up to 25X longer life versus standard grinding discs
Cons
- No warranty term is stated
- Life and speed figures are comparisons against grinding discs, not cut counts
- 48 teeth, fewer than the Diablo 70, for thin sheet work
- No coating is stated

6-1/2 Inch Metal Cutting Circular Saw Blade
A 6-1/2 inch, 40-tooth cermet blade with a 5/8 inch arbor and a 6000 max RPM, listed for metal roofing, siding and thin sheets.
Pros
- Listed for metal roofing, siding, angle iron and thin sheets
- Cermet carbide tooth, able to cut very hard steel
- Laser-cut stabilizer vents trap noise and vibration
- Diamond knockout arbor for worm drive saws
Cons
- No warranty term is stated
- 6-1/2 inch diameter, smaller than the 7-1/4 inch blades here
- 40 teeth, fewer than the 70-tooth Diablo, for thin sheet work
- No coating is stated

HARDWIN 7-1/4 Inch Metal Cutting Circular Saw
A 7-1/4 inch, 48-tooth cermet blade with a 5/8 inch arbor and a thin kerf, for steel, angle iron and threaded rod.
Pros
- 48 cermet carbide teeth for steel, angle iron and threaded rod
- Ultra-thin kerf design reduces material waste
- Anti-rust and anti-stick coating with a laser-cut steel core
- Noise-reduction tooth geometry for smooth, low-vibration cutting
Cons
- No warranty term is stated
- No max RPM is stated
- No thickness ranges are stated
- The listing recommends professional metal cutting equipment

Evolution Power Tools 185BLADEST Steel Cutting Saw
A 7-1/4 inch, 40-tooth TCT blade for mild steel only, with a thin kerf and virtually no sparks, but not for galvanized steel.
Pros
- Made from high-quality Japanese carbide, heat-treated for durability
- No heat, no burrs and virtually no sparks, so the cut can be touched within moments
- Thin kerf design for accurate cuts and extended tool life
- Hardened steel body minimises vibration
Cons
- The listing states no warranty
- Mild steel only: do not use for galvanized, hardened or high-carbon steel
- No arbor size is stated
- No max RPM is stated
Other welders and gear to compare
DEWALT Circular Saw BladeCheck price on Amazon
FOXBC 7 1/4 inch Metal Circular Saw Blade 48 TeethCheck price on Amazon
5-3/8"Check price on Amazon
Milwaukee 49-22-1178 T-Shank Metal/Wood Cutting Jig Saw BladeCheck price on Amazon
GRAFF 4-1/2 Inch Circular Saw Blade with 3/8 Inch ArborCheck price on Amazon
Spec sheet comparison
| Model | Gear Score | Diameter | Teeth | Arbor | Max RPM | Kerf | Warranty |
|---|---|---|---|---|---|---|---|
| Diablo Steel Demon | 9.7/10 | 7-1/4 in | 70 | Not stated | Not stated | Thin | Not stated |
| FOXBC 48T Cermet | 9.6/10 | 7-1/4 in | 48 | 5/8 in | 5800 | .075 in | Not stated |
| Echo Corner 6-1/2 | 9.6/10 | 6-1/2 in | 40 | 5/8 in | 6000 | 0.071 in | Not stated |
| HARDWIN 48T Cermet | 9.6/10 | 7-1/4 in | 48 | 5/8 in | Not stated | Thin | Not stated |
| Evolution 185BLADEST | 9.6/10 | 7-1/4 in | 40 | Not stated | Not stated | Thin | Not stated |
Ratings in this table are the makers’ own claims taken from each product page (11 November 2026).
Buying guide: choosing the best saw blade for cutting metal roofing
Tooth count and thin metal
The Diablo has 70 teeth and is made for mild steel, 12 gauge or thinner. The FOXBC and HARDWIN blades have 48 teeth, and the Echo Corner and Evolution blades have 40 teeth. For thin roofing panels, the 70-tooth Diablo is the pick made for thin metal. The 48-tooth blades suit a mix of steel, angle iron and threaded rod, and the 40-tooth blades suit small and medium mild steel and angle iron. The steel sheet metal gauge chart shows what 12 gauge means in thickness.
Diameter and arbor
Match the diameter to your saw: the Echo Corner is 6-1/2 inches, while the Diablo, FOXBC, HARDWIN and Evolution blades are 7-1/4 inches. Check the arbor against your saw: the Echo Corner, FOXBC and HARDWIN blades use a 5/8 inch arbor, and the Echo Corner adds a diamond knockout for worm drive saws. The Diablo and Evolution listings state no arbor size, so check the listing before you buy.
Galvanized steel and roofing
The Evolution blade is made for mild steel only, and the listing says not to use it for galvanized, hardened or high-carbon steel. If the roofing panels are galvanized, that blade is not the pick. The FOXBC blade lists metal and stainless steel, and the Diablo blade is made for mild steel, 12 gauge or thinner. Check the panel material against the blade listing before you cut.
Kerf and heat
A thin kerf cuts with low resistance and fast cuts. The FOXBC lists a .075 inch kerf, and the Echo Corner lists a 0.071 inch kerf tip thickness. The Diablo, Evolution and HARDWIN listings state a thin kerf with no figure. The FOXBC maker claims up to 50X cooler cuts versus a grinding disc, and the Diablo triple chip grind reduces sparks and minimizes heat build-up.
Max RPM and vents
The Echo Corner lists a 6000 max RPM, and the FOXBC lists a 5800 max RPM. The Diablo, HARDWIN and Evolution listings state no max RPM, so check the listing against your saw. Laser-cut stabilizer vents appear on the Echo Corner, Diablo and FOXBC blades, trapping noise and vibration and keeping the blade cool for straight, accurate cuts.
Before You Strike an Arc
- Check the arbor: the Echo Corner, FOXBC and HARDWIN blades use a 5/8 inch arbor, and the Echo Corner adds a diamond knockout for worm drive saws.
- Check the diameter against your saw: the Echo Corner is 6-1/2 inches, and the other blades here are 7-1/4 inches.
- Check the material: the Evolution blade is made for mild steel only, not for galvanized, hardened or high-carbon steel.
- Check the max RPM: the Echo Corner lists 6000 and the FOXBC lists 5800, while the other listings state no max RPM.
- The Diablo and Evolution listings state no arbor size, so check the listing before you buy.
FAQ for welders
What saw blade cuts metal roofing?
A carbide or cermet circular saw blade made for thin metal. The Diablo is made for mild steel, 12 gauge or thinner, with 70 teeth, and the Echo Corner is listed for metal roofing, siding and thin sheets.
Can I cut galvanized roofing with any of these blades?
Not with the Evolution blade: it is made for mild steel only, and the listing says not to use it for galvanized, hardened or high-carbon steel. The FOXBC blade lists metal and stainless steel, and the Diablo blade is made for mild steel, 12 gauge or thinner.
What size blade fits a circular saw for roofing?
The Diablo, FOXBC, HARDWIN and Evolution blades are 7-1/4 inches, and the Echo Corner is 6-1/2 inches. Match the diameter to your saw, and check the arbor: the Echo Corner, FOXBC and HARDWIN blades use a 5/8 inch arbor.
How many teeth should a metal roofing blade have?
The Diablo has 70 teeth for thin metal, the FOXBC and HARDWIN have 48 teeth, and the Echo Corner and Evolution have 40 teeth. For thin roofing panels, the 70-tooth Diablo is the pick made for thin metal.
Do these blades fit cordless saws?
The Diablo, FOXBC and HARDWIN blades are made for cordless and corded circular saws. The Echo Corner is made for hand-held circular saws, and the Evolution is a circular saw blade with no cordless or corded note stated.
Scoring, line by line
Each blade is scored on performance, build, value, safety and warranty, using only what the listing publishes. Performance weighs the tooth count, the kerf and the material range the listing states; build weighs the tooth material and the stabilizer vents; value weighs the blade size and the stated ranges. No listing here states a safety standard or a warranty term with a length, so all 5 score zero for safety and warranty. The weights are on our How We Pick page.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Diablo Steel Demon | 9.7 | 32 | 21 | 21 | n/a | 0 |
| FOXBC 48T Cermet | 9.6 | 30 | 21 | 21 | n/a | 0 |
| Echo Corner 6-1/2 | 9.6 | 30 | 20 | 21 | n/a | 0 |
| HARDWIN 48T Cermet | 9.6 | 29 | 20 | 21 | n/a | 0 |
| Evolution 185BLADEST | 9.6 | 28 | 20 | 20 | n/a | 0 |
The lowest score we show is 9.2 and the highest is 9.8; every point total is spread proportionally across that span, so extra points mean a higher figure. Where safety does not apply (unpowered gear with no listed safety features), it is left out and the remaining 90 points make up the score.
More welding guides
See the metal fab tools hub, our band saw blade sizes chart and our best angle grinders. For sheet thickness, see the steel sheet metal gauge chart.




