Steel Sheet Metal Gauge Chart and Thickness Guide
A steel sheet metal gauge chart turns a gauge number into a thickness in inches, and the gauges in this guide let you check the sheet in your hand before you cut or weld.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
2 Pcs Stainless Steel Thickness Gauges Wire Gauge9.5/10View on Amazon - 2
Alffun 4 Pcs 18 Gauge Sheet Metal Plates9.5/10View on Amazon - 3
2 Pack Wire Metal Sheet Thickness Gauge Stainless9.4/10View on Amazon - 4
Weewooday 3 Pcs Metal Thickness Gauge Tool Welding9.4/10View on Amazon
A sheet of steel on the bench raises the same question on every job: how thick is this sheet, and what gauge does that make it? A steel sheet metal gauge chart answers it by pairing each gauge number with a thickness in inches, so a number on a label or a gauge tool turns into a measurement to cut, bend or weld by. Read the gauge number, read across to the thickness, and check the sheet itself with a gauge before starting work, because a label can be wrong and a sheet can measure thinner than it looks.
This guide links to our product roundups, where WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.

2 Pcs Stainless Steel Thickness Gauges Wire Gauge
A two-piece stainless gauge set that prints gauge-to-thickness figures from 24 gauge to 10 gauge, plus fractional slots, for checking sheet before welding.
Pros
- Prints gauge figures from 24 gauge to 10 gauge
- Round wire gauge plus sheet gauge in one set
- Stainless steel, rust-resistant per the listing
- Clear numbers and letters, per the listing
Cons
- 1/8 inch slot listed at .0125, which does not match the fraction
- No warranty term is stated
- No certification is stated
- No dimensions are stated in the spec table

Alffun 4 Pcs 18 Gauge Sheet Metal Plates
Four 18-gauge cold-rolled steel plates, each 12 by 9 inches, for practice and small fabrication.
Pros
- 18-gauge, 1.2 mm plates as listed
- 4 plates in the pack
- Cold-rolled low carbon steel, weldable per the listing
- Flat surface with burr-free edges
Cons
- Light protective oil needs wiping before use
- One gauge only in the pack
- No warranty term is stated
- No certification is stated

2 Pack Wire Metal Sheet Thickness Gauge Stainless
A stainless wire and sheet thickness gauge set with a laser-etched scale, a round dual-sided gauge and a sheet gauge, plus a storage bag.
Pros
- Laser-etched scale, wear-resistant per the listing
- 2Cr13 stainless steel, firm and durable per the listing
- Round wire gauge plus sheet gauge in one set
- Storage bag included for carrying
Cons
- No gauge-to-thickness figures are stated
- No warranty term is stated
- No certification is stated

Weewooday 3 Pcs Metal Thickness Gauge Tool Welding
Three stainless sheet thickness gauges, 1.0 inch wide and 2.8 inches long, with AWG and imperial markings for quick checks before welding.
Pros
- 3 gauges in the pack
- Stainless steel, anti-rust per the listing
- AWG and imperial markings
- Pocket size at 1.0 by 2.8 inches
Cons
- No gauge-to-thickness figures are stated
- No warranty term is stated
- No certification is stated
How to read the steel sheet metal gauge chart
Gauge numbers run the other way from thickness: a higher gauge number means a thinner sheet, and a lower gauge number means a thicker one. The chart below shows it in the figures the gauge in this guide states: 24 gauge lists at .0239 inch, while 10 gauge lists at .1345 inch, so the sheet gets thicker as the gauge number falls. Find the gauge number on the label or on the gauge tool, then read across to the thickness in inches and use that thickness for the cut, the bend or the weld setting.
| Gauge or size | Thickness in inches |
|---|---|
| 24 gauge | .0239 |
| 22 gauge | .0299 |
| 20 gauge | .0359 |
| 18 gauge | .0478 |
| 16 gauge | .0598 |
| 14 gauge | .0747 |
| 10 gauge | .1345 |
| 1/8 inch | .0125 as listed |
| 3/16 inch | .1875 |
| 1/4 inch | .250 |
| 5/16 inch | .3125 |
The chart lists only the gauges the Pimoys gauge (on Amazon) states, so it skips gauges the listing does not print. One entry needs care: the listing pairs its 1/8 inch slot with .0125, which does not match the fraction printed beside it, so do not rely on that one slot. The fractional slots run from 1/8 inch to 5/16 inch, with 3/16 inch at .1875, 1/4 inch at .250 and 5/16 inch at .3125.
Measure before working, not after. Slip the edge of the sheet into the slot marked with its gauge and read the marking stamped beside the slot that fits. The Pimoys listing notes to place wire in the slot, not the hole, and to strip wire insulation before gauging wire, which is a reminder that the slot is the measuring part of the tool. A gauge reading beats a guess, and it beats trusting a label on a plate that has passed through several hands.
Side by side
| Product | Type | Pack | |
|---|---|---|---|
| Pimoys Dual Gauge Set | Wire and sheet gauge set | 2 pieces | |
| Alffun 18 Ga Plates | 18-gauge steel plates | 4 plates | |
| Yuntop Gauge Set | Wire and sheet gauge set | 2 pack | |
| Weewooday 3-Pc Gauge | Sheet thickness gauges | 3 pieces |
Each example is scored on performance, build, value, safety and warranty, using only what the listing publishes. The Pimoys set carries the chart figures in this guide, while the other gauges state no gauge-to-thickness figures of their own, so they score on the tool itself rather than on a chart.
Gauge tools and steel plates for this job
The chart answers the question, and the gauges check the sheet in your hand against it, while the steel plates give you an 18-gauge sheet to measure and weld.
Oil, edges and fumes. Wipe the light protective oil off the plates before welding, per the listing, and work with ventilation. Sheet edges can cut, so handle plates with gloves and wear safety glasses when cutting. See the OSHA welding overview and our Safety Disclaimer.
FAQ for welders
What thickness is 18 gauge steel?
The gauge in this guide lists 18 gauge at .0478 inch. The Alffun plates (on Amazon) are listed as 18 gauge, 1.2 mm cold-rolled steel, so the inch figure comes from the gauge and the millimetre figure comes from the plate listing.
Is a higher gauge number thicker or thinner?
Thinner. The chart shows 24 gauge at .0239 inch and 10 gauge at .1345 inch, so the thickness rises as the gauge number falls. Read the number, then read the thickness beside it, rather than guessing from the number alone.
How do you measure sheet metal with a gauge tool?
Slip the edge of the sheet into the slot marked with a gauge number and read the marking beside the slot that fits. The Pimoys listing notes that wire goes in the slot, not the hole, with insulation stripped first, and the same slot-first habit applies to sheet. Measure before cutting or welding, and measure in more than one spot when the sheet looks uneven.
What gauge are the steel plates in this guide?
The Alffun plates are 18 gauge, 1.2 mm cold-rolled steel, in a pack of 4 plates that each measure 12 by 9 inches. The listing states the steel is low carbon, with a light protective oil coating that wipes clean before use. Check the plate against the chart at 18 gauge, .0478 inch, before welding.
Do the gauge tools here measure wire as well as sheet?
The Pimoys round gauge covers 0 to 36 American standard wire gauge, the Yuntop set includes a round dual-sided wire gauge for wire diameter, and the Weewooday gauges carry AWG and imperial markings. The Alffun plates are steel to measure, not a measuring tool. Use the round gauge for wire and the flat sheet gauge for sheet.
Related: metal fab tools hub, best sheet metal gauge thickness tool, best tin snips for sheet metal and best MIG welder for hobbyist.




