Cut Off Wheel vs Cold Saw: Which One Should You Buy?
Cut off wheels on a grinder and cold-cut blade machines compared by heat, burr, capacity, consumables and portability, with the stated specs.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
VEVOR Chop Saw, 7-1/4 in Stainless Steel Cold Cut9.6/10View on Amazon - 2
Benchmark Abrasives 4.5" Aluminum Oxide Type 1 Cut9.6/10View on Amazon - 3
EZARC Metal Cut Off Wheels, 6'' x .045'' x 7/8''9.5/10View on Amazon - 4
PTOOL PT-101 Cutting Edge Saw9.5/10View on Amazon
Verdict. Cut off wheel vs cold saw, short answer: pick the abrasive wheel if you already own an angle grinder and make short cuts in pipe, tube and rebar. Pick a cold-cut blade machine for a clamped, repeatable cut (the VEVOR chop saw) or a hand-held rebar tool (the PTOOL).
A length of tube needs cutting square, and the choice is between a thin disc on a grinder and a toothed blade on a machine. Neither machine here is a classic bench cold saw. The VEVOR is a chop saw with a cold cut blade, and the PTOOL is a hand-held rebar cutter. So this is abrasive wheel on a grinder against cold-cut blade machines, set side by side on heat, burr, capacity, cost per cut and portability, using what each listing states.
WeldGearLab gets a commission on purchases made through links on this page, and your price stays the same. Read our affiliate disclosure.
The four picks

VEVOR Chop Saw, 7-1/4 in Stainless Steel Cold Cut
A 1200W chop saw with a 7-1/4-inch stainless steel cold cut blade, 4000 RPM, a 0-45-degree adjustable angle and an auto-return guard.
Pros
- 1200W 10A motor at 4000 RPM
- 7-1/4-inch stainless steel cold cut blade
- 0-45-degree adjustable cutting angle
- Auto-return guard and quick-lock mechanism
Cons
- No warranty term is stated
- 14.44 lb, heavier than the 8.0 lb PTOOL
- Cuts 2.76 inches wide and 2.56 inches thick, so larger stock needs another tool
- No arbor size is stated

Benchmark Abrasives 4.5" Aluminum Oxide Type 1 Cut
A 25-count pack of 4.5-inch Type 1 aluminum oxide cut off wheels with a 7/8-inch arbor, rated to 13,000 RPM for metal and stainless steel.
Pros
- 25-count pack of 4.5-inch wheels
- Rated to 13,000 RPM
- 7/8-inch arbor for 4-1/2 and 5 inch angle grinders
- Meets ANSI and EU standards
Cons
- No warranty term is stated
- Needs a 4-1/2 or 5 inch angle grinder
- No max cut depth is stated
- No stated grit

EZARC Metal Cut Off Wheels, 6'' x .045'' x 7/8''
A 25-pack of 6-inch cut off wheels, .045 inches thick with a 7/8-inch arbor, glass fiber reinforced and rated to 10,200 RPM.
Pros
- 25-pack of 6-inch wheels
- Thin .045-inch design for quick, straight cuts
- Glass fiber reinforced
- Complies with EN 12413 and ASM07
Cons
- Title states 6-inch wheels while the listed dimensions say 4.53 inches
- No warranty term is stated
- Rated to 10,200 RPM, a ceiling the grinder must stay under
- No max cut depth is stated

PTOOL PT-101 Cutting Edge Saw
A hand-held electric rebar cutter with a cold cut blade, 1100W at 120V 60Hz, that cuts up to 1.4-inch rebar within 10 seconds.
Pros
- Cuts up to 1.4-inch rebar within 10 seconds
- 1100W motor at 120V 60Hz
- Ceramic carbide blade with minimal sparks
- Overload protection
Cons
- No warranty term is stated
- No blade size is stated
- Hand-held only, no bench mount stated
- No cutting angle adjustment is stated
Other welders and gear to compare
FOXBC 4-1/2 Inch Diamond Cutting Wheel Metal Cut Off forCheck price on Amazon
50 PCS 6 Inches Cutting Wheel for GrindingCheck price on Amazon
100 PCS 5 Inch Cut Off WheelCheck price on Amazon
Truswe Cut Off Wheels 4 1/2 inchCheck price on Amazon
United Abrasives-SAIT 23101 A60S General Purpose Cut-OffCheck price on Amazon
DEWALT DW8020 Metal Port Saw Cut-Off WheelCheck price on Amazon
Side by side
| Tool | Gear Score | Side | Size | Stated cut quality | Weight |
|---|---|---|---|---|---|
| VEVOR Cold Cut Saw | 9.6/10 | Cold-cut blade, bench | 7-1/4 in blade | Smooth, burr-free | 14.44 lb |
| Benchmark 4.5 Wheels | 9.6/10 | Cut off wheel | 4.5 in | Burr-free | Not stated |
| EZARC 6-Inch Wheels | 9.5/10 | Cut off wheel | 6 in (title) | Barely noticeable burrs | Not stated |
| PTOOL Rebar Cutter | 9.5/10 | Cold-cut blade, hand-held | Not stated | Burr-free, cool to the touch | 8.0 lb |
Specifications are manufacturer rated, as published on each listing as of 11 November 2026. None of the four listings states a warranty term.
Cut off wheel vs cold saw: heat and burr
Heat is where the two sides differ most on paper, and only one listing speaks to it. The PTOOL states a burr-free, cool-to-the-touch cut surface with minimal sparks. The VEVOR states smooth, burr-free cuts from its cold cut blade. The Benchmark wheels state burr-free cuts and the EZARC wheels state barely noticeable burrs, but neither wheel listing says anything about heat, so the comparison leaves that unclear for the wheels rather than calling it a loss.
Speed figures do not rate the same thing. A wheel listing gives the maximum safe speed of the disc, up to 13,000 RPM for the Benchmark and up to 10,200 RPM for the EZARC: a ceiling your grinder must stay under. The VEVOR 4000 RPM is the running speed of its own motor and blade. The PTOOL states no speed. None of these numbers ranks one side over the other.
Capacity and what each side cuts
The Benchmark wheels cut steel, stainless steel, cast iron, aluminum and rebar, with no maximum cut depth stated. The EZARC wheels cut carbon steel, stainless steel, pipe, cast iron and copper, also with no depth stated. The VEVOR states a 2.76-inch cutting width and a 2.56-inch cutting thickness, on square and flat tubes and I-shaped steels. The PTOOL cuts up to 1.4-inch rebar within 10 seconds, plus conduit, steel tubing, steel pipe, copper pipe and all-thread.
Cost per cut and consumables
The listings give no cost-per-cut figure, so compare what each one consumes. The wheels are consumables sold in 25-count packs: a worn disc is swapped for a fresh one. The VEVOR states its blade delivers more than 3,500 cuts. The PTOOL lists a ceramic carbide blade but states no cut count or blade size.
Portability and setup
The wheels state no weight and ride on a grinder you already own: the Benchmark fits 4-1/2 and 5 inch grinders, and the EZARC is sold for 6-inch grinders. The PTOOL weighs 8.0 lb and measures 4.0 by 5.4 by 6.5 inches, so it travels to the job. The VEVOR weighs 14.44 lb and measures 14.57 by 9.06 by 15.16 inches, and it clamps the work with a quick-adjustment wrench.
Safety features stated
The Benchmark wheels meet ANSI and EU standards, and the EZARC wheels comply with EN 12413 and ASM07. The EZARC listing also states to wear suitable protective equipment and not to exceed the stated maximum speed. The VEVOR has an auto-return guard and a quick-lock mechanism, and the PTOOL has overload protection. None of the four listings states a CSA, UL or ETL listing.
Who should skip which
Skip the wheels if you have no grinder, since the listings sell the discs alone. Skip the VEVOR if you need a hand-held tool or stock beyond its stated cutting width and thickness. Skip the PTOOL if you need an adjustable angle or a stated blade size. The EZARC also lists two different sizes, a 6-inch wheel in its title and 4.53 inches in its listed dimensions, which the review below covers.
Before You Strike an Arc
- Power: the VEVOR motor is 1200W at 10A and the PTOOL motor is 1100W at 120V 60Hz; check the circuit and the plug before the first cut.
- Arbor: both wheel listings state a 7/8-inch arbor, so check the arbor on your grinder before buying.
- Consumables: the wheel listings are 25-count packs, and the VEVOR blade is stated for more than 3,500 cuts.
- On arrival: check the VEVOR auto-return guard and the PTOOL overload protection work as described.
- Protection: the EZARC listing states to wear suitable protective equipment and not to exceed the stated maximum speed.
FAQ for welders
Can a cut off wheel cut stainless steel?
The Benchmark listing states its wheels cut stainless steel, and the EZARC listing states its wheels cut stainless steel as well. Both wheel listings state burr-free cuts or barely noticeable burrs.
What speed do cut off wheels run at?
The Benchmark wheels are rated up to 13,000 RPM, and the EZARC wheels are rated up to 10,200 RPM. The EZARC listing states not to exceed the stated maximum speed.
Do cold-cut blades run cooler than cut off wheels?
The PTOOL listing states a burr-free, cool-to-the-touch cut surface with minimal sparks, and the VEVOR listing states smooth, burr-free cuts from a cold cut blade. The wheel listings say nothing about heat, so the cool-to-the-touch surface is the PTOOL’s own stated feature.
Which side is better for rebar?
Both sides cut rebar: the Benchmark wheels list rebar, and the PTOOL cutter cuts up to 1.4-inch rebar within 10 seconds. The EZARC wheels do not name rebar, and the VEVOR saw names tube and I-shaped steels.
Do these picks have a warranty?
None of the four listings states a warranty term. The comparison scores all four at zero on warranty.
Related: the metal fab tools hub, the best electric rebar cutter, the angle grinder uses and the bolt cutters vs rebar cutter.
Scoring, line by line
Each pick is scored on performance, build, value, safety and warranty, using only what the listing publishes. Safety points come from stated standards and guards, and no listing here states a warranty term, so all four score zero on warranty. The How We Pick page explains the weights.
| Product | Gear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| VEVOR Cold Cut Saw | 9.6 | 30 | 21 | 21 | 5 | 0 |
| Benchmark 4.5 Wheels | 9.6 | 29 | 21 | 21 | 4 | 0 |
| EZARC 6-Inch Wheels | 9.5 | 28 | 20 | 20 | 5 | 0 |
| PTOOL Rebar Cutter | 9.5 | 27 | 20 | 20 | 4 | 0 |
Think of 9.2 as the bottom and 9.8 as the top. Totals are placed between them in proportion, which keeps the order intact: more points, higher score.




